Table of Contents
Advertisement
Bulletin MSG11 5715-662/UK
Operating instructions
Series D1VW*-SC / D1DW*-SC (NG6)
Series D3W*-SC / D3DW*-SC (NG10)
Series D31DW*-SC (NG10)
Series D41VW*-SC (NG16)
Series D81VW*-SC / D91VW*-SC (NG25)
Translation of German original operating instructions
Series D1VW / D1DW / D3W / D3DW
Directly operated directional control valves
Subplate mounted
Slider type
Series D31DW / D41VW / D81VW / D91VW
Pilot operated directional control valves
Subplate mounted
Slider type
Parker Hannifin
Manufacturing Germany GmbH & Co. KG
ndustrial Systems Division Europe
Gutenbergstr. 38
41564 Kaarst, Germany
E-mail: isde.kaarst.support@support.parker.com
Copyright © 2022, Parker Hannifin Corp.
Advertisement
Table of Contents
Related Manuals for Parker D1VW -SC Series
Summary of Contents for Parker D1VW -SC Series
- Page 1 Series D31DW / D41VW / D81VW / D91VW Pilot operated directional control valves Subplate mounted Slider type Parker Hannifin Manufacturing Germany GmbH & Co. KG ndustrial Systems Division Europe Gutenbergstr. 38 41564 Kaarst, Germany E-mail: isde.kaarst.support@support.parker.com Copyright © 2022, Parker Hannifin Corp.
- Page 2 The user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.
-
Page 3: Table Of Contents
Series D1VW / D1DW Series D3W / D3DW Series D31DW Series D41VW Series D81VW / D91VW Dimensions Series D1VW / D1DW Series D3W / D3DW Series D31DW Series D41VW Series D81VW / D91VW MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 4: Basic Information
Product name loss or damage is not the responsibility The safety valves of series D1VW* / D1DW* / D3W* of Parker Hannifin. / D3DW* / D31DW* / D41VW* / D81VW* / D91VW* If the described product is installed in a are named DCV in the rest of the documentation. -
Page 5: Electronic Control System
(see the technical Size Min. 1.5 mm² data). External diameter PG9: 4.5...7 mm PG11: 6...9 mm A suitable tool must if necessary be used Length Max. 50 m for manual emergency actuation of the solenoid. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 6: Pressure Fluids
Any health and safety warnings attached to the product must be observed and must be maintained in a legible state. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 7: Personnel Requirements
"Technical is a malfunction, the product must be data" (section 16). returned to the manufacturer. DCV valves with position control are not suitable for use in Ex areas (gas/dust). MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 8: Temperature
(see to use. section 8. "Installation instructions DCV" and sec- tion 16. "Position control switch"). MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 9: Storage
Access should be provided to the hydraulic dia- valve must be returned to the manufac- gram, the equipment list and the logic diagram for turer. the system/machine. The DCV valves must only be installed as indicated in ISO 4401. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 10: Installation Instructions Dcv
To guarantee that the main piston operates reliably at all times, the minimum pilot pressure must be provided. To achieve this, a suitable combination of flow and return arrangements must be selected for the pilot oil. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... - Page 11 Check ambient temperature at Temperature drift. the valve Check the temperature of the medium at the valve Position control incorrectly set Return the valve to the manu- facturer for inspection MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation...
-
Page 12: Modification
"Personnel requirements" and 3. "Remaining risk". supply has been disconnected and steps have been take to ensure it cannot be reconnected unintentionally. As part of servicing/maintenance, only the fol- lowing items can be replaced with original Parker replacement parts: • Accessible O-rings (sealing surfaces) •... -
Page 13: Other Documentation
HLP; Minimum requirements moulding machines - Safety requirements • DIN EN ISO 4413:2011-04 • DIN EN 60204-1/A1:2009-10; VDE 0113-1/ Hydraulic fluid power - General rules and safety requirements for sysstems and their compo- A1:2009-10 nents MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 14: Declaration Of Conformity
Series D1VW / D1DW / D3W / D3DW / D31DW / D41VW / D81VW / D91VW Declaration of Conformity safety to an unacceptable degree. This Any unauthorised structural change or would invalidate the declaration of con- addition to the product may jeopardise formity supplied with the product. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 15: Technical Data
Pin 2 Out neg. Voltage max. 1.8 V Stroke Voltage min. -2.5 V [mm] (-10) (+40) switching point Outputs: Open collector Only guaranted with screened cable and female connector Type 118368-01 Type 118370-01 MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... - Page 16 Series D1VW / D1DW / D3W / D3DW / D31DW / D41VW / D81VW / D91VW Installation Please order female connector M12x1 separately, order no.: 5004109 Wiring female connector (View screw terminal connection) 19.2 ... 28.8 V MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation...
-
Page 17: Series D1Vw / D1Dw
Connector to EN 175301-803, solenoid identification to ISO 9461 Wiring min. [mm²] 3 x 1.5 recommended Wiring length max. [m] 50 recommended Please note that with electrical connections the protective conductor (PE W) must be connected according to the relevant regulations. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 18: Series D3W / D3Dw
Connector to EN 175301-803, solenoid identification to ISO 9461 Wiring min. [mm²] 3 x 1.5 recommended Wiring length max. [m] 50 recommended Please note that with electrical connections the protective conductor (PE W) must be connected according to the relevant regulations. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 19: Series D31Dw
Connector to EN 175301-803, solenoid identification to ISO 9461 Wiring min. [mm²] 3 x 1,5 recommended Wiring length max. [m] 50 recommended Please note that with electrical connections the protective conductor (PE W) must be connected according to the relevant regulations. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 20: Series D41Vw
Connector to EN 175301-803, solenoid identification to ISO 9461 Wiring min. [mm²] 3 x 1,5 recommended Wiring length max. [m] 50 recommended Please note that with electrical connections the protective conductor (PE W) must be connected according to the relevant regulations. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 21: Series D81Vw / D91Vw
Connector to EN 175301-803, solenoid identification to ISO 9461 Wiring min. [mm²] 3 x 1,5 recommended Wiring length max. [m] 50 recommended Please note that with electrical connections the protective conductor (PE W) must be connected according to the relevant regulations. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 22: Dimensions
The space necessary to remove the plug per EN 175301-803, design type AF is at least 15 mm. The torque for the screw M3 of the plug has to be 0.5 to 0.6 Nm. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 23: Series D3W / D3Dw
The space necessary to remove the plug per EN 175301-803, design type AF is at least 15 mm. The torque for the screw M3 of the plug has to be 0.5 to 0.6 Nm. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 24: Series D31Dw
* Please order female connector M12x1 separately, order no.: 5004109 Surface finish 4x M10x60 NBR: SK-D41VW-N-91 63 Nm ±15 % 0,01/100 BK320 2x M6x55 6 3 . 13.2 Nm ±15 % FPM: SK-D41VW-V-91 ISO 4762-12.9 MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation... -
Page 25: Series D81Vw / D91Vw
The space necessary to remove the plug per EN 175301-803, design type AF is at least 15 mm. The torque for the screw M3 of the plug has to be 0.5 to 0.6 Nm. MSG11-5715-662 DCV UK.indd 21.07.22 Parker Hannifin Corporation...