Cisco MGX 8230 Installation And Configuration Manual page 198

Cisco systems edge concentrator installation and configuration guide
Table of Contents

Advertisement

Configuring Frame Relay Service
For MGX-FRSM-HS1/B
cnfbctype is the command to change a 12-in1 back card type between support for x.21 and v.35.
addport <port_num> <port_type>
port_num is the port number in the range 1–4.
port_type is a number representing the type of frame interface technology for the logical port: 1 for
Frame Relay; 2 for FUNI mode-1a; or 3 for frame forwarding.
For AX-FRSM-8T1 and AX-FRSM-8E1:
addport <port_num> <line_num> <ds0_speed> <begin_slot> <num_slot> <port_type>
port_num is the logical port number in the range of either 1–192 for T1 or 1–248 for E1. When you
subsequently add a connection through the preferred command addcon or the addchan command
(which requires NSAP format), you must indicate a logical port by using this singular port_num
regardless of the number of DS0s. (You can add 1–24 DS0s to a single line through the other
addport parameters.)
line_num is the physical line number in the range 1–8.
ds0_speed is a number representing the DS0 speed: 1 for 56 Kbps or 2 for 64 Kbps.
begin_slot is the beginning DS0 timeslot in 1 base. For example, on port number 50, you could
specify begin_slot to be 9, then specify num_slot to be in the range 1–16.
num_slot is the consecutive DS0s that each connection on port_num has.
port_type is a number representing the mode of operation for the logical port: 1 for Frame Relay; 2
for FUNI mode-1a; and 3 for frame forwarding.
Modify as needed the signaling on a port by executing cnfport.
Step 5
cnfport <port_num> <lmi_sig> <asyn> <elmi> <T391> <T392> <N391> <N392> <N393>
port_num is the logical port number with a range that depends on the type of FRSM:
lmi_sig specifies the LMI signaling. 1=Other, 2=None, 3=StrataLMI, 4=AnnexAUNI,
5=AnnexDUNI, 6=AnnexANNI, 7=AnnexDNNI LMI signaling, N=none, S=StrataLMI, and
au=AnnexAUNI.
asyn enables asynchronous updates: (y)es or (n)o.
elmi enables Enhanced LMI: (N or n) disable (Y or y) enable.
T391 sets the T391 timer. The range is 5–30 seconds. It sets the interval in seconds for NNI status
polling. The default is 10.
T392 sets the T392 timer. The range is 5–30 seconds. It sets the interval in seconds for UNI status
polling. The default is 15.
N391 sets the N391 counter (the number of UNI/NNI polling cycles). The range is 1–255. The
default is 6.
N392 sets the N392 counter (the threshold for UNI/NNI errors). The range is 1–10. The default is 3.
N393 sets the N393 counter (the UNI/NNI threshold for monitored events). The range is 1–10 and
must be greater than the value of N392. The default is 4.
Cisco MGX 8230 Edge Concentrator Installation and Configuration
6-30
For the MGX-FRSM-2CT3, 1–56.
For a channelized AX-FRSM-8T1, 1–192.
For a channelized AX-FRSM-8E1, 1–248.
For the unchannelized cards, the range equals the number of lines.
Chapter 6
Card and Service Configuration
Release 1.1.31, Part Number 78-11215-03 Rev. B0, May 2001

Advertisement

Table of Contents
loading

Table of Contents