Cisco 7513 Series Manual
Cisco 7513 Series Manual

Cisco 7513 Series Manual

Chassis replacement and upgrade instructions

Advertisement

Text Part Number:
78-1897-02
Cisco 7513 and Cisco 7576
Chassis Replacement and Upgrade
Instructions
Product Numbers: CHAS-7513-DC=, CHAS-7513-AC=, MAS-7513= (Cisco 7513)
CHAS-7576-DC=, CHAS-7576-AC=, MAS-7576=, and UPG-7513/7576= (Cisco 7576)
Customer Order Number: DOC-781897=
This publication provides instructions for replacing a Cisco 7513 or Cisco 7576 chassis, which is
available as a spare part. It also includes instructions on upgrading a Cisco 7513 to a Cisco 7576.
Note
Also, the term RSP is used to refer to the RSP2 and RSP4 Route Switch Processors that are
compatible with the Cisco 7513 and Cisco 7576.
The chassis is available as a spare part and as a kit to upgrade a Cisco 7513 to a Cisco 7576. The
chassis includes all of the components required for operation except the processor modules and
power supplies (MAS-7513=), (MAS-7576=), as a spare with power supplies (CHAS-7513-DC=,
CHAS-7576-DC=, CHAS-7513-AC=, CHAS-7576-AC=), and as a kit to upgrade the Cisco 7513 to
a Cisco 7576 (UPG-7513/7576=). After you replace the chassis, you must move the processor
modules from your old chassis into your new chassis.
Note
Refer to the "Upgrading a Cisco 7513 to a Cisco 7576" section on page 5 for more information. In
addition, the replacement chassis and the upgrade kit do not include the cable-management bracket
or rack-mounting hardware kits. You can move the rack-mounting hardware and cable-management
bracket from the existing chassis, or order either kit as a spare part.
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Copyright © 1996-1998
Cisco Systems, Inc.
All rights reserved.
In this document, the term chassis is used to refer to the Cisco 7513 or Cisco 7576 chassis.
The Cisco 7576 Upgrade Kit does not contain RSPs, interface processors, or power supplies.
1

Advertisement

Table of Contents
loading

Summary of Contents for Cisco 7513 Series

  • Page 1 Cisco 7513 and Cisco 7576. The chassis is available as a spare part and as a kit to upgrade a Cisco 7513 to a Cisco 7576. The chassis includes all of the components required for operation except the processor modules and...
  • Page 2: Table Of Contents

    Network interfaces reside on interface processors that provide a direct connection between two CyBuses in the Cisco 7513 and your external networks. The Cisco 7513 has 13 slots: interface processor slots 0 through 5, Route Switch Processor (RSP) slots 6 and 7, and interface processor slots 8 through 12.
  • Page 3: What Is The Cisco 7576

    CyBuses in the Cisco 7576 and your external networks. The backplane of the Cisco 7576 has 13 slots and provides two routers on a single split backplane, designated router A and router B. Router A uses interface processor slots 0 through 5 and a Route Switch Processor (RSP4) in slot 6.
  • Page 4 What is the Cisco 7576? The Cisco 7576 (see Figure 2) is similar in most respects to the Cisco 7513. The differences between the two models are found in the backplane and the interface processor slot numbering scheme (see Figure 3) on the card cage.
  • Page 5: Upgrading A Cisco 7513 To A Cisco 7576

    Reinstall RSPs and interface processors. Step 5 If you are only configuring one of the two routers that make up the Cisco 7576, make sure to Caution configure router A instead of router B. To configure router A, install an RSP in slot 6 and install interface processors only in slots 0 through 5.
  • Page 6: Chassis Replacement Or Upgrade Prerequisites

    Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta). 6 Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 7 Se förklaringar av de varningar som förkommer i denna publikation i dokumentet Regulatory Compliance and Safety Information (Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföljer denna anordning. Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 8: Safety Guidelines

    Ensure that your footing is solid, and balance the weight of the object between your feet. • Lift the object slowly; never move suddenly or twist your body as you lift. 8 Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 9 • Serial interface cables (all types) use thumbscrews on the cable connectors that secure the cable to the Fast-Serial Interface Processor (FSIP) port. Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 10 When removing any cable, pull the cable out at the connector; never pull or tug on the cable itself. For detailed descriptions of the system components, refer to the Cisco 7500 Series Installation and Configuration Guide.
  • Page 11: Tools And Parts Required

    (pan head screws are included with the brackets): — Number 1 phillips screwdriver — Cable-management bracket — Two M3 x 8-mm, phillips pan head screws Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 12: Replacing Or Upgrading The Chassis

    You can leave the system components in the old chassis until after you install the new, empty chassis in the rack. 12 Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 13 Cisco 7513 and Cisco 7576 Rack-Mount Kit Installation Instructions (Publication Number 78-2023-xx). After you install the new chassis in the rack and install the cable-management brackets, proceed to the “Moving Processor Modules from the Old Chassis...
  • Page 14 Use a screwdriver to loosen and remove each of the four screws (two on each side) that secure the chassis ears to the rack rails. Pull the chassis out of the rack and place it on the floor or a table. Step 3 14 Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 15 With the chassis positioned so the front is closest to the rack, insert the front of the chassis into the rack between the brackets, and then slowly lower the chassis until it rests on the two bracket ledges. (See Figure 7.) Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 16 (See Figure 7.) Secure each ear to the rack-mounting post with two 10-32 x 5/8-inch, phillips pan-head Step 5 screws. This completes the procedure for moving the chassis into the rack. 16 Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 17 On the interface processor end of the chassis, locate the two slotted screws positioned below the blower module and above the card cage. (See Figure 8.) Figure 8 Cable-Management Bracket Blower module Loosen screws (2) Bracket Card cage Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 18 At the interface processor end of the chassis, slots contain the processor modules. (See Figure 1.) In the Cisco 7513, the RSP occupies RSP slot 6 or 7. In the Cisco 7576, the RSP placed in slot 6 controls router A and the RSP in slot 7 controls router B. The remaining 11 slots support any combination of interface processors.
  • Page 19 Use the optional cable-management brackets to keep the interface cables untangled and away from other interface processor slots and ports. The Cisco 7513 and Cisco 7576 allow you to remove and replace interface processors and Note RSPs while the system is powered on; however, you must shut down the system power before accessing the chassis interior for any other reason.
  • Page 20 Replacing or Upgrading the Chassis Figure 9 Ejector Levers and Captive Installation Screws Bottom ejector lever Processor module slot Processor module carrier guide Captive installation screw Stop immediately on contact 20 Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 21 Note If you are upgrading a Cisco 7513 to a Cisco 7576, you need to carefully consider how you will transfer the existing RSP(s) and interface processors from the Cisco 7513 to the Cisco 7576. For example, if the existing Cisco 7513 includes two RSPs utilizing the HSA feature, keep in mind that this configuration is not supported in the Cisco 7576.
  • Page 22 “Installing the New Chassis in the Rack” section on page 15. Otherwise, proceed to the next section to check the installation. 22 Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 23: Checking The Installation

    If you need technical assistance, refer to the “Cisco Connection Online” section on page 29. Ensure that the system power switch is off, and then reconnect the power cable to the AC Step 1 receptacle or DC terminal block, as required.
  • Page 24 (For descriptions and examples of these commands, refer to the following section, “Verifying the Installation Using show Command Descriptions and Examples.”) 24 Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 25 ROM labels or by configuring the interface or system software to boot from ROM, restarting the system, and using these same commands to check the running version. The following examples may differ based on the router model and version of Cisco IOS Note software that is being used.
  • Page 26 Router> show int hssi 1/0 Hssi 1/0 is up, line protocol is up Hardware is cxBus HIP Internet address is 1.1.1.9, subnet mask is 255.255.255.0 (display text omitted) 26 Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 27 The command show protocols displays the global (system-wide) and interface-specific status of any configured Level 3 protocol. Router> show protocols Global values: Internet Protocol routing is enabled Hssi1/0 is up, line protocol is up (display text omitted) Cisco 7513 and Cisco 7576 Chassis Replacement and Upgrade Instructions...
  • Page 28: Port And Slot Configuration Worksheet

    The port and slot configuration worksheet (Table 1) is used in conjunction with Figure 12 to assist in planning and documenting your use of the slots in a Cisco 7513 or Cisco 7576 router. Figure 12 shows the dual CyBus backplane without the Time Division Multiplexing (TDM) connectors found on the Cisco 7576.
  • Page 29: Cisco Connection Online

    Serial Number Slots 6 and 7 are reserved for the RSPs in the Cisco 7513 and Cisco 7576. However, in the Cisco 7576, slot 6 is used for router A, and slot 7 is used for router B. Cisco Connection Online Cisco Connection Online (CCO) is Cisco Systems’...
  • Page 30 Systems, the Cisco Systems logo, Enterprise/Solver, EtherChannel, FastHub, ForeSight, FragmentFree, IP/TV, IPX, LightStream, MICA, Phase/IP, StrataSphere, StrataView Plus, and SwitchProbe are registered trademarks of Cisco Systems, Inc. in the U.S. and certain other countries. All other trademarks mentioned in this document are the property of their respective owners.

Table of Contents