Briggs & Stratton Murray Pro Series Owner's Manual
  1. Manuals
  2. Brands
  3. Briggs & Stratton Manuals
  4. Snow Blower
  5. Murray Pro Series
  6. Owner's manual
Briggs & Stratton Murray Pro Series Owner's Manual

Briggs & Stratton Murray Pro Series Owner's Manual

10.0 hp 30 two-stage power-propelled snow thrower
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER'S
MANUAL
MODEL NO.
630106X31
(96197001200)
Caution:
Read and fol low
all Safety Rules
and In struc tions
Be fore Op er at ing
This Equip ment
Briggs & Stratton Power Products Group, LLC • Jefferson, WI 53549
10.0 HP
30" TWO-STAGE
POWER-PROPELLED
SNOW THROWER
• Assembly
• Operation
• Maintenance
• Service and Adjustments
• Repair Parts

Advertisement

Table of Contents
loading

Related Manuals for Briggs & Stratton Murray Pro Series

Summary of Contents for Briggs & Stratton Murray Pro Series

  • Page 1 OWNER’S MANUAL MODEL NO. 630106X31 (96197001200) Caution: Read and fol low 10.0 HP all Safety Rules 30" TWO-STAGE and In struc tions Be fore Op er at ing POWER-PROPELLED This Equip ment SNOW THROWER • Assembly • Operation • Maintenance •...

  • Page 2: Safety Rules

    IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions.

  • Page 3: Table Of Contents

    6. When cleaning, repairing or inspecting the snow thrower, Clearing a Clogged Discharge Chute stop the engine and make certain the collector/impeller Hand contact with the rotating impeller inside the discharge and all moving parts have stopped. Disconnect the chute is the most common cause of injury associated with spark plug wire and keep the wire away from the plug snow throwers.

  • Page 4: Warranty

    PARTS PACKED SEPARATELY IN CARTON...

  • Page 5: Assembly / Pre-Operation

    ASSEMBLY / PRE-OPERATION Read these instructions and this manual in its entirety INSTALL SPEED CONTROL ROD (See Figs. 1 and 2) before you attempt to assemble or operate your new 1. Remove plastic tie securing rod to lower handle. snow thrower. Reading the entire manual will familiar- 2.
  • Page 6 ASSEMBLY / PRE-OPERATION INSTALL TRACTION DRIVE CONTROL ROD INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) (See Figs. 3 and 4) The auger control rod has the short loop on the end of the spring as shown. The traction drive control rod has the long loop on the end of the spring as shown.
  • Page 7 ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATER INSTALL CHUTE DEFLECTOR REMOTE CONTROL HEAD (See Fig. 7) (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with NOTE: The multi-wrench provided in your parts bag may 5/16-18 carriage bolt and 5/16-18 locknut as shown.

  • Page 8: Operation

    OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product.
  • Page 9 OPERATION SPARK ENGINE OIL CAP AUGER DISCHARGE DEFLECTOR DRIVE PLUG WITH DIPSTICK CONTROL CHUTE REMOTE SPEED SAFETY LEVER CON TROL CONTROL CONTROL IGNITION LEVER LEVER LEVER GAS O LINE FILLER CHUTE CHOKE DE FLEC TOR CON- TROL TRACTION DRIVE CONTROL DRAIN LEVER PLUG...
  • Page 10 OPERATION The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating FULL your snow thrower or performing any ad just - ments or repairs.
  • Page 11 OPERATION TO THROW SNOW (See Fig. 15) TO MOVE FORWARD AND BACKWARD (See Fig. 17) The auger rotation is controlled by the auger control lever SELF-PROPELLING, forward and reverse movement of located on the right side handle. the snow thrower, is controlled by the traction drive control lever located on the left side handle.
  • Page 12 OPERATION 1. Shut off engine and wait for all moving parts to stop. WARNING: Wipe off any spilled oil or 2. Adjust skid plates by loosening the rear 1/2" hex nut fuel. Do not store, spill or use gasoline only, then moving skid plate to desired position. Be sure near an open fl...
  • Page 13 OPERATION 2. Place throttle control in FAST position. 3. While the engine is running, push starter button and spin the starter for several seconds. 3. Rotate choke control to FULL position. NOTE: The unusual sound made while starter is spinning 4.

  • Page 14: Maintenance

    MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that SAE 5W-30 Motor Oil have been sub ject ed to operator abuse or negligence. To receive full value from the warranty, operator must maintain See “ENGINE”...
  • Page 15 MAINTENANCE V-BELTS TO CHANGE ENGINE OIL Check V-belts for deterioration and wear after every 50 Determine temperature range anticipated before next oil hours of operation and replace if necessary. The belts change. All oil must meet API service classifi cation SG–SL. are not ad just able.

  • Page 16: Service And Adjustments

    SERVICE AND ADJUSTMENTS 1. Disengage all controls and move throttle control to WARNING: To avoid serious injury, before STOP position. Wait for all moving parts to stop. performing any service or ad just ments: 2. Disconnect spark plug wire from spark plug and place 1.
  • Page 17 SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 23) The auger and traction drive belts are not adjustable. If the HINT: Insert a 3/8" drive ratchet (in the “ON” position) into belts are damaged or begin to slip from wear, they should the square hole in idler arm and rotate ratchet clockwise be replaced.

  • Page 18: Storage

    SERVICE AND ADJUSTMENTS TO REMOVE WHEELS (See Fig. 24) NOTE: To seal punctures or prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts • Remove the klik pin and remove wheel from axle. dealer.

  • Page 19: Troubleshooting

    TROUBLESHOOTING See appropriate section in manual unless directed to a qualifi ed service centre/department. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2.

  • Page 20: Repair Parts

    REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) AUGER HOUSING / IMPELLER ASSEMBLY...
  • Page 21 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) AUGER HOUSING / IMPELLER ASSEMBLY PART PART DESCRIPTION DESCRIPTION 191079 Pulley, Impeller 407768 O-Ring 188909 Bearing Assembly, Flange 407769 Bushing, Flange 3/4 198541 Nut, Hex Flange 5/16-18 174681 Washer, Thrust 3/4 180355 Bolt, Flat Head, Carriage 5/16-18 174684 Bearing, Thrust 3/4...
  • Page 22 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) CONTROL PANEL / DISCHARGE CHUTE...
  • Page 23 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) CONTROL PANEL / DISCHARGE CHUTE KEY PART DESCRIPTION 183333 Knob, Lever 17501010 Screw #10-24 x 5/8 179096X479 Strap, Slotted 73800600 Nut, Lock 3/8-16 19131316 Washer, Flat 3/8 404974 Control Assembly, Chute Rotater 405784X479 Support, Pivot 150078...
  • Page 24 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) HANDLES...
  • Page 25 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) HANDLES KEY PART DESCRIPTION 405783X479 Lever, Auger Control, RH 405999X479 Lever, Traction Drive Control, LH 178888 Bushing, Flange 169675 Retainer, Hairpin 17060406 Screw, Hex Head 1/4-20 x 3/4 178652 Rod, Interlock 196333X008 Arm, Impeller Rod 196334X008 Arm, Traction Rod 196619X479 Panel, Control...
  • Page 26 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) DRIVE 9 10...
  • Page 27 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) DRIVE KEY PART DESCRIPTION 751153 Nut, Lock 5/16-18 198584 Screw, Hex Head 5/16-18 x 1/2 180017 Bearing, Flange 180134 Shaft, Auxiliary 179270 Spacer, Plate 192616X479 Plate, Auxiliary 180082 Gear, Intermediate (12/58) 180065 Gear, Pinion 187714 Rod, Clutch...
  • Page 28 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) CHASSIS / ENGINE / PULLEYS 10 21...
  • Page 29 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) CHASSIS / ENGINE / PULLEYS KEY PART KEY PART DESCRIPTION DESCRIPTION 181044 Spring, Traction Idler 851084 Screw, Hex Head 3/8-24 x 1-3/8 180522 Pulley, Idler (2-1/4) 155452 Guide, Belt - - - Engine, Tecumseh, Model Number 192213 Belt Cover Assembly...
  • Page 30 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) WHEELS / DECALS...
  • Page 31 REPAIR PARTS SNOW THROWER - MODEL NO. 630106X31(96197001200) WHEELS / DECALS KEY PART DESCRIPTION 187833X417 Wheel Assembly, 16", LH 155443 Pin, Klik 1/4 187865X417 Wheel Assembly, 16", RH 146315 Screw, Hex Head 5/16-18 x 3/4 179830 Bearing, Axle 174697 Washer, Thrust (1") KEY PART DESCRIPTION 181037...
  • Page 32 Murray Pro Series 4 Year Warranty The Home Depot Canada is doubling the warranty period of the manufacturer’s warranty and those of the companies that manufacture engines, accessories, transmissions, bat- teries, transaxles and other sourced components. To make claim under this warranty does not change. Return the unit, or if authorized in advance, the defective part, along with your proof of purchase to The Home Depot Canada store where purchased or closest to you, or, to an authorized Service Dealer.

This manual is also suitable for:

Murray pro 630106x3196197001200

Table of Contents