Outsider Plateau Mounting Instruction

Hide thumbs

page of 17

/ 17
Bookmarks

Quick Links

Download this manual

MOUNTING

PLATEAU

INSTRUCTION

#177

Parts included:

2 pcs M8x20 bolts

20 pcs M6x10 bolts

16 pcs M6x30 bolts

8 pcs M10x60 bolts

8 pcs M10 nut

2 pcs long discs

4 pcs round discs

out-sider a/s

info@out-sider.dk

Kigkurren 8A, Islands Brygge

+45 2261 7420

DK-2300 Copenhagen S

www.out-sider.dk

24.01.2017

Need help?

Do you have a question about the Plateau and is the answer not in the manual?

Questions and answers

Summary of Contents for Outsider Plateau

Page 1 MOUNTING 24.01.2017 PLATEAU INSTRUCTION #177 Parts included: 2 pcs M8x20 bolts 20 pcs M6x10 bolts 16 pcs M6x30 bolts 8 pcs M10x60 bolts 8 pcs M10 nut 2 pcs long discs 4 pcs round discs out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge...
Page 2 #177 PLATEAU - MOUNTING 24.01.2017 1. Unpacking the shipment Cut the safety straps, remove protective material and unbox screws and legs out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge +45 2261 7420 DK-2300 Copenhagen S www.out-sider.dk...
Page 3 #177 PLATEAU - MOUNTING 24.01.2017 2. Prepare for mounting legs Lift the seat and place two boxes, pallets or equivalent item under each side. The bench must be raised minimum 350mm. Raise min. 350mm Raise min. 350mm out-sider a/s info@out-sider.dk...
Page 4 #177 PLATEAU - MOUNTING 24.01.2017 3. Legs mounting, step 1 Slide leg into corner of bench plate, making sure holes in flange and bench are aligened out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge +45 2261 7420 DK-2300 Copenhagen S www.out-sider.dk...
Page 5 #177 PLATEAU - MOUNTING 24.01.2017 4. Legs mounting, step 2 After fitting the first leg, make sure to angle the other leg before sliding into the corner out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge +45 2261 7420 DK-2300 Copenhagen S...
Page 6 #177 PLATEAU - MOUNTING 24.01.2017 5. Legs mounting, step 3 Once each leg is fitted into corner of bench plate, turn towards oppenent leg, and make sure square flanges are parrallel. Square flanges out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge...
Page 7 #177 PLATEAU - MOUNTING 24.01.2017 6. Legs mounting, step 4 Use allen key (size 5) to mount 5 x M6x10mm bolts at each corner as shown in right figure. The bolts are placed in a box, which comes with the shipment.
Page 8 #177 PLATEAU - MOUNTING 24.01.2017 7. Mount joint cover tubing, step 1 Turn one leg aside to make room for fitting joint cover tubing. Slide tubing over the assembly plate. Make sure the hole in joint cover tubing points towards center of table.
Page 9 #177 PLATEAU - MOUNTING 24.01.2017 7. Mount joint cover tubing, step 2 Once fitted over the assembly plate, turn opponent leg back towards middle, and make sure leg tubing fits closely to joint cover tubing. out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge...
Page 10 #177 PLATEAU - MOUNTING 24.01.2017 8. Mount joint cover tubing, step 3 Below figures show correct position of assembly plates. Joint shown with joint cover tubing mounted M8 thread Ø12mm Assembly plate with M8 thread must point outwards. Assembly plate with Ø12mm hole must point inwards.
Page 11 #177 PLATEAU - MOUNTING 24.01.2017 9. Mount joint cover tubing, step 4 Screw the two M8x20mm bolts into the assembly plates. NB - do not fully tighten the bolts until step 12 out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge +45 2261 7420 DK-2300 Copenhagen S www.out-sider.dk...
Page 12 #177 PLATEAU - MOUNTING 24.01.2017 10. Position seat assembly with legs onto table Lift and place seat assembly on top table assembly, and make sure leg tubes align with holes in table frame. out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge...
Page 13 #177 PLATEAU - MOUNTING 24.01.2017 11. Mount legs to table with bolts Use the attached M6x30mm bolts to assemble legs and table. Tighten bolts gently using allen key (size 5). out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge +45 2261 7420 DK-2300 Copenhagen S www.out-sider.dk...
Page 14 #177 PLATEAU - MOUNTING 24.01.2017 12. Tighten M8x20mm bolts at assembly plates Use allen key (size 6) to tighten the two M8 bolts. out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge +45 2261 7420 DK-2300 Copenhagen S www.out-sider.dk...
Page 15 #177 PLATEAU - MOUNTING 24.01.2017 12. Install round and elongated discs, step 1 Install 9mm Ø50mm tubing under each circular disc. Elongated discs installs directly into table plate. out-sider a/s info@out-sider.dk Kigkurren 8A, Islands Brygge +45 2261 7420 DK-2300 Copenhagen S...
Page 16 #177 PLATEAU - MOUNTING 24.01.2017 13.Install round and elongated discs, step 2 Mount 4 x M10 bolts at each corner under bench plate. Mount 4 x M10 bolts under table plate at leg assemble point. Mount M10 bolt using allen key (size 8)
Page 17 #177 PLATEAU - MOUNTING 24.01.2017 14. Cleaning and maintenance Clean the laminate surfaces using pure hot water and soft sponge. Do not use abbrasive “green” side of sponges. If stains cannot be removed as described in step 1, common household cleaners without abbrasives eg.

This manual is also suitable for:

177