Frymaster OCF30ATOG Service & Parts Manual page 76

2.5.2 Component Boxes cont.
ITEM PART #
1 810-1164
2 816-0217
√ 3 807-3843
√ * 826-1157
807-3293
* 106-0531SP
√ 4 807-5008
* 807-5009
* 807-3484
5 807-4199
* 807-5165
6 806-6085SP
7 220-6102
√ 8 807-2971
√ 9 807-1006
√ 10 8073366†
√ 8073365†
√ 8075949
√ 11 826-2264
807-4330
807-4343
√ 12 807-0833
√ 13 807-0834
14 810-2243
15 108-1094
16 824-2090
17 824-2091
18 220-7085
19 108-1544
20 807-1683
21 106-0531SP
* 807-2659
* 807-4403
22 108-1260
108-2353
23 806-4973
24 108-2581
* Not illustrated.
√ Recommended parts.
† For Full-vat units, use one 807-3366 Dual Spark Ignition Module (see NOTE 1).
† For Dual-vat units, use two 807-3365 Single Spark Ignition Modules (see NOTE 1).
NOTE 1: U.S., Canadian, and Mexican units use two different modules depending upon the configuration of the frypot.
Full-Vat units use one 807-3366 Dual-Spark Ignition Module while Dual-Vat units use two 807-3365 Single-Spark Igni-
tion Modules. Also, in full-vat units, only two latch relays (Item 12) are used, located in the sockets on the right side of
the interface board. These relays are located in the bottom sockets of the interface board and control the heating circuit.
NOTE 2: The relays in the top sockets control the basket lifts (Item 13) and are present only on units equipped with
basket lifts.
Block, One-Piece Screwless Terminal
Insulation, Terminal Block Paper
Fuse 3A 250V Domestic
Kit, Fuse and Fuse Puller (2 Fuses)
Fuse 5A 125V International Only
Fuse Assy, Inline
Cable, 21-inch Ignition – For 807-3366/807-3365 Modules
Cable, Ignition 19" (CE)
Connector, Rajah
Cable, 20-pin Controller to 15-pin Interface Board – SMT for fryers with CM 3.5 control-
ler.
Cable, 20-pin Controller to 15-pin Interface Board – SMT for fryers with 3000 controller.
Wire Assembly, Ignitor
Box, One-Piece Component
Ignition Module, (Australia)
Ignition Module, CE
Ignition Module, Honeywell Dual-Spark Full-Vat (Domestic and Non-CE export unit
except Australia)
Ignition Module, Honeywell Single-Spark Dual-Vat (Domestic and Non-CE export unit
except Australia)
Ignition Module, Fenwal Single-Spark Full/Dual-Vat (Domestic and Non-CE export unit
except Australia) (Use 8263446 for a Conversion Kit – NOTE: 2 kits are needed to con-
vert a Full Vat.)
Interface Board Kit SMT
Speaker Adapter Harness SMT
Wire Harness, SMT Interface Board to Ignition Module
Relay, DPDT 5A 12VDC Latch (See NOTE 1.)
Relay, SPDT 15A 12VDC Basket Lift (See NOTE 2.)
Spring, Relay Retaining
Plate, Ignition Module
Cover, Ignition Module
Cover, Ignition Module CE
Cover, Ignition Module Australia
Plate, Ignition Module Australia
Relay, 12VDC Secondary Blower Fan to cool frypot
Fuse Assembly, Inline (not used on all models)
Switch, Momentary (Control Power Reset, only used in far left component box)
Speaker SMT
Wire Assembly, Ignition Module Domestic and Non-CE export, except Australia.
Wire Assembly, Ignition Module CE
Interface Board, Australia
Harness, Secondary Blower
COMPONENT
2-9