Table of Contents
Troubleshooting
Related Manuals for Frymaster OCF30E
Summary of Contents for Frymaster OCF30E
- Page 1 Frymaster, a member of the Commercial Food Equipment Service Association, recommends using CFESA Certified Technicians. 24-Hour Service Hotline 1-800-551-8633 06/2018 *8196686* www.frymaster.com E-mail: fryservice@welbilt.com...
- Page 2 FROM FRYMASTER DEAN, OR ANY OF ITS FACTORY AUTHORIZED SERVICERS, AND/OR THE PART BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS WARRANTY WILL BE VOID. FURTHER, FRYMASTER DEAN AND ITS AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS, DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION OF ANY MODIFIED PART AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE CENTER.
- Page 3 A restraint kit is provided with the fryer. If the restraint kit is missing contact your local KES. DANGER Prior to movement, testing, maintenance and any repair on your Frymaster fryer, disconnect all electrical power from the fryer. ELECTRICAL POWER SPECIFICATIONS...
-
Page 4: Table Of Contents
™ OCF30 SERIES ELECTRIC FRYERS TABLE OF CONTENTS CAUTIONARY STATEMENTS ..........................i ELECTRICAL POWER SPECIFICATIONS ......................ii CHAPTER 1: Service Procedures General ..............................1-1 Replacing a Controller ........................... 1-1 Replacing Component Box Components ....................1-1 Replacing a High-Limit Thermostat ...................... 1-3 Replacing a Temperature Probe ...................... - Page 5 2.5.7 Controllers .......................... 2-15 2.5.8 Wiring ..........................2-16 2.5.8.1 Contactor Box Wiring Assemblies 12-Pin Dual Vat .......... 2-16 2.5.8.2 Contactor Box Wiring Assemblies 12-Pin Full Vat ..........2-16 2.5.8.3 Contactor Box Wiring Assemblies 6-Pin Left Element ........2-17 2.5.8.4 Contactor Box Wiring Assemblies 9-Pin Right Element ........2-17 2.5.8.5 Main Wiring Harnesses ..................
-
Page 6: Chapter 1: Service Procedures
SERIES ELECTRIC FRYERS CHAPTER 1: SERVICE PROCEDURES 1.1 General Before performing any maintenance on your Frymaster fryer, disconnect the fryer from the electrical power supply. WARNING To ensure the safe and efficient operation of the fryer and hood, the electrical plug must be fully engaged and locked in its pin and sleeve socket. - Page 7 2. Open the control panel by removing the screws on the bottom of the bezel. Carefully lower the bezel. 3. Remove the two screws from the upper corners of the control panel and allow the control panel to swing down. 4.
-
Page 8: Replacing A High-Limit Thermostat
1.4 Replacing a High-Limit Thermostat 1. Drain the frypots into a Shortening Disposal Unit (SDU) or other appropriate METAL container. DANGER DO NOT drain more than one full frypot into the SDU at one time. 2. Disconnect the fryer from the electrical power supply and reposition it to gain access to the rear of the fryer. - Page 9 4. Locate the red and white wires of the temperature probe to be replaced. Note where the leads are connected prior to removing them from the connector. Unplug the 12-pin connector C-6 and using a pin-pusher push the pins of the temperature probe out of the connector. 5.
-
Page 10: Replacing A Heating Element
Replacing a Heating Element 1. Perform steps 1-5 of section 1.5, Replacing a Temperature Probe. 2. Disconnect the wire harness containing the probe wiring. Using a pin pusher, disconnect the probe wires from the 12-pin connector C-6. 3. In the rear of the fryer, disconnect the 6-pin connector for the left element (as viewed from the front of the fryer) or the 9-pin connector for the right element from the contactor box. -
Page 11: Replacing Contactor Box Components
Index Marker marks Position 1 8. Reconnect the element connector ensuring that the latches lock. 9. Insert the temperature probe leads into the 12-pin wiring harness connector (see illustration below). For full-vat units or the right half of a dual-vat unit, the red lead goes into position 3 and the white into position 4. -
Page 12: Replacing A Frypot
Remove two screws to access contactor box components above the filter 4. The contactors and relays are held on by threaded pin studs so that only removal of the nut is required to replace the component. 5. After performing necessary service, reverse steps 1-4 to return the fryer to operation. Left and right views of mechanical contactor box components. - Page 13 5. Unplug the wiring harnesses and ground wires from the backs of the controllers. Remove the controllers by lifting them from the hinge slots in the control panel frame. 6. Remove the screws from the bottom of the lower back panel attaching the contactor plug guards. 7.
-
Page 14: Built-In Filtration System Service Procedures
26. Reconnect the oil return and auto top off flexlines to the frypot, and replace aluminum tape, if necessary, to secure heater strips to the flexlines. 27. Insert the high-limit thermostat leads disconnected in step 18 (see illustration on page 1-3 for pin positions). -
Page 15: Replacing The Filter Motor, Filter Pump And Related Components
Solidified shortening in the pan or filter Sediment Particle lines, or Attempting to filter unheated oil or shortening (cold oil and shortening are Oil Flow more viscous, overloading the pump motor and causing it to overheat). If the motor runs but the pump does not return oil, there is a blockage in the pump. - Page 16 3. Disconnect the flexline running to the oil-return manifold at the rear of the fryer as well as the pump suction flexline at the end of the filter pan connection (see photo below). On some models a third flexline may need to be disconnected. Disconnect flexlines indicated by the arrows.
-
Page 17: Replacing The Filter Transformer Or Filter Relay
11. When proper operation has been verified, reinstall the back panels and the filter pan and lid. 12. Reposition the fryer under the exhaust hood and reconnect it to the electrical power supply, if necessary to return the fryer to service. 1.9.3 Replacing the Transformer or Filter Relay Disconnect the fryer from the electrical power supply. - Page 18 cut, allowing the upper circuit to be activated. The basket lift rises and re-closes the lower microswitch. When the basket lift rod clears the upper microswitch, the microswitch reopens, power to the circuit is cut, and the motor stops. Pushing the product button restarts the cycle. Problems with the basket lift can be grouped into three categories: Binding/jamming problems ●...
-
Page 19: Ato (Automatic Top-Off) Service Procedures
Electronic Issues Within this category are problems associated with the relays, microswitches, capacitors, resistors, interface board, wiring, and controls. The most common problem in this category is a lift that continuously travels up and down. This is usually caused by a microswitch that is out of adjustment. Troubleshooting the electronics of a modular basket lift is simply a process of verifying current flow through the individual components up to and including the motor. -
Page 20: Ato (Automatic Top-Off) Troubleshooting
1.11.1 ATO (Automatic Top-off) Troubleshooting Problem Probable Causes Corrective Action A. Ensure the JIB is not out of oil and supply line is in the JIB. Replace JIB and press the button when prompted to reset top off system. Remove supply line from pump and blow air through line towards JIB. -
Page 21: Testing Ato Rtd Probes
Problem Probable Causes Corrective Action Check power to the pump. If the pump is hot, the solenoid has probably Failed solenoid failed. One vat tops off but Loose wire connection. Ensure all wiring harnesses are other vats fail to top off. securely connected to ATO board and solenoids. -
Page 22: Ato (Automatic Top-Off) Board Pin Positions And Harnesses
1.11.3 ATO (Automatic Top-Off) Board Pin Positions and Harnesses Wire Connector From/To Harness # Function Voltage Color Green Output DV - Vat #1 Output FV - Vat #1 8075161 Green Output DV - Vat #2 Ground Solenoids 8075162- Output FV - Vat #2 (4 or 5 battery) Green Output DV - Vat #3... -
Page 23: Replacing The Ato Board, Ato Pump Relay Or Transformer
1.11.4 Replacing the ATO Board, ATO Pump Relay or Transformer Disconnect the fryer from the electrical power supply. Locate the ATO box (see Figure 1 on page 14), behind the JIB (Jug In Box). Remove the cover to expose the transformer and ATO board (see Figure 2). -
Page 24: Control Power Reset
1.11.7 Control Power Reset Switch The control power reset switch is a momentary rocker switch located behind the control box, (see Figures 6 and 7) above the JIB, which resets all power to all the controllers and boards in the fryer. It is necessary to reset all power after replacing any controller or board. - Page 25 Problem Probable Causes Corrective Action Fryers using the 3000 controller can toggle between F° to C° by pressing the button until Main Menu changing to Product setup is displayed. Press to scroll to Tech Mode and press . Enter 3000 display is in 1658.
- Page 26 Problem Probable Causes Corrective Action This indicates a problem within the 3000 display shows Problem with the temperature measuring temperature probe circuitry. Check TEMP PROBE circuitry including the probe. resistance of probe, if faulty replace FAILURE. probe. 3000 display shows Swap the controller wiring harness with PROBE FAILURE Damaged controller wiring harness or...
-
Page 27: 3000 Controller Useful Codes
1.12.2 3000 Controller Useful Codes To enter any of the following codes: Press and hold the button until Main Menu changing to Product setup is displayed. Press to scroll to Tech Mode and press . TECH MODE ENTER CODE is displayed. Enter a code number below: ... -
Page 28: Error Log Codes
1.12.4 Error Log Codes Code ERROR MESSAGE EXPLANATION ERROR TEMP PROBE FAILURE TEMP Probe reading out of range HI 2 BAD High limit reading is out of range. HOT HI 1 High limit temperature is past more than 410°F (210°C), or in CE countries, 395°F (202°C) HEATING FAILURE A component has failed in the high limit circuit such as controller, interface board, contactor or... -
Page 29: 3000 Menu Summary Tree
1.12.5 3000 Menu Summary Tree Reflected below are the major programming sections in the 3000 and the order in which submenu headings will be found under the sections in the 3000 Operation Manual (819-6985). See section 1.6-1.8 Adding New Product Menu Items Filter Menu ...………………..………………………………………………………………………………….. -
Page 30: 3000 Controller Pin Positions And Harnesses
1.12.6 3000 Controller Pin Positions and Harnesses Connector From/To Harness PN Function Voltage Wire Color 12VAC In 12VAC Ground 12VAC In 12VAC FV Heat Demand V Relay 12VDC DV Heat Demand R/H B/L 12VDC Black Analog Ground L/H B/L 12VDC 8074199 Interface ALARM... -
Page 31: Loading And Updating Software
1.13 Loading and Updating Software Procedures Updating the software takes approximately 30 minutes. The software only needs to be loaded in ONE controller and it will update all the controllers and boards in the system. Press the TEMP button to check current 3000/ATO software version. Remove the bezel by removing the screws under the bottom of the bezel. -
Page 32: Interface Board Diagnostic Chart
1.14 Interface Board Diagnostic Chart The following diagram and charts provide ten quick system checks that can be performed using only a multimeter. Diagnostic LED Legend indicates power from 12V transformer indicates power from 24V transformer (RH) indicates output (closed) from right latch relay (LH) indicates output (closed) from left latch relay (RH) indicates output from right heat relay... -
Page 33: Probe Resistance Chart
1.15 Probe Resistance Chart Probe Resistance Chart For use with fryers manufactured with Minco Thermistor probes only. OHMS OHMS OHMS OHMS OHMS 1059 1204 1350 1493 1634 1070 1216 1361 1503 1644 1080 1226 1371 1514 1654 1091 1237 1381 1524 1664 1101... -
Page 34: Chapter 2: Parts List
OCF™ SERIES ELECTRIC FRYERS CHAPTER 2: PARTS LIST 2.1 Accessories ITEM PART # COMPONENT 230-8165 Hanger, Basket Single 230-7495 Hanger, Basket Two Station 230-7497 Hanger, Basket Three Station 230-7495 (2) Hanger, Basket Four Station 803-0197 Cleanout Rod, 27-inch 803-0429 Brush, Frypot 823-7263 Connecting Strip, Frypot prior to 07/2014 108-6157... -
Page 35: Basket Lift Assembly And Associated Parts
2.2 Basket Lift Assembly and Associated Parts... - Page 36 2.2 Basket Lift Assembly and Associated Parts cont. ITEM PART # COMPONENT Basket Lift Assemblies (see Note 1 in illustration) 106-1808SP Basket Lift Assembly, 100-120VAC w/Relay (Items 1-20) shown 106-1805SP Basket Lift Assembly, 200-220VAC w/Relay (Items 1-20) shown 106-1806SP Basket Lift Assembly, 230-250VAC w/Relay (Items 1-20) not shown 810-1012 Rod, Basket Lift 813-0035...
-
Page 37: Doors, Sides, Tilt Housings, Top Caps And Casters
2.3 Doors, Sides, Tilt Housings, Top Caps and Casters ITEM PART # COMPONENT 231-0323 Side, Standard Cabinet Left SS (use 221-0323 for Enameled Steel) 232-0323 Side, Standard Cabinet Right SS (use 222-0323 for Enameled Steel) 810-1105 Magnet, Door (vertical) (use 810-2346 for horizontal over filter pan) 106-4397 Door, Left or Right (Left shown –... -
Page 38: Drain System Components
2.4 Drain System Components 2.4.1 Drain Tube Sections and Associated Parts See Section 2.4.2 for Drain Valves... - Page 39 2.4.1 Drain Tube Sections and Associated Parts cont. ITEM PART# COMPONENT 823-8141 Drain Tube, Dump Full-Vat Left Closed/Right End Open 823-8142 Drain Tube, Dump Dual-Vat Left Closed/Right End Open 823-8143 Drain Tube, Dump Full-Vat Left Closed Both Ends 823-7939 Drain Tube, Dump Single Full-Vat Left Closed Both Ends 823-8144 Drain Tube, Dump Dual-Vat Left Closed Both Ends 823-7936...
-
Page 40: Drain Valve Assembly
2.4.2 Drain Valve Assembly ITEM PART # COMPONENT 108-2451 Valve, Assembly Drain FV OCF with Filter 108-2452 Valve, Assembly Drain DV OCF with Filter 108-2593 Valve, Assembly Drain FV OCF Single with Filter 108-2450 Valve, Assembly Drain DV Right OCF Single with Filter 108-2449 Valve, Assembly Drain DV Left OCF Single with Filter 809-0540... -
Page 41: Electronics And Wiring Components
2.5 Electronics and Wiring Components 2.5.1 Component Boxes... - Page 42 2.5.1 Component Boxes cont. ITEM PART # COMPONENT 106-5592 Box Assembly, Component 200-3300 Bracket, Component Box Strain Relief √ 3 807-0012 Relay, Filter 18A, 1/3HP 24VAC √ 4 807-0670 Relay, Filter DPDT 20A 24VAC √ 5 807-4770 Relay, 240V DPDT 20A √...
-
Page 43: Contactor Boxes
2.5.2 Contactor Boxes 14/17kW LEFT AND RIGHT MECHANICAL CONFIGURATIONS 11 12 11 12 SOLID STATE RELAY LEFT AND RIGHT CONFIGURATIONS 120/440/480v LEFT AND RIGHT STANDARD AND MECHANICAL CONFIGURATIONS The configurations illustrated show all possible components, but a particular NOTES: configuration may not have all the components shown. ITEM PART # COMPONENT... -
Page 44: Fuse Boxes
2.5.3 Fuse Boxes Left Fuse Box Assembly Right Fuse Box Assembly 106-5505/106-6678 106-5506/106-6679 ITEM PART # COMPONENT 810-0519 Hinge 807-3970 Block, 3 Pole 600V 175A Terminal 807-0501 Fuse Block, Buss #2968 3-Pole 807-2240 Fuse, 60 AMP 300VAC 807-0070 Terminal, Ground Lug 807-0128 Bushing, Insulating Heyco 2-11... -
Page 45: Terminal Blocks
2.5.4 Terminal Blocks ITEM PART # COMPONENT 823-5631 Box, LH Rear Terminal Block 823-5632 Box, RH Rear Terminal Block 220-0801 Cover, Rear Terminal Block Box 807-3970 Block, 3 Pole 600V 175A 807-0070 Terminal, Ground Lug 807-0128 Bushing, Insulating Heyco 2-12... -
Page 46: Heating Element Assemblies And Hardware
2.5.5 Heating Element Assemblies and Hardware NOTE: These elements apply only to FPEL series fryers. 2-13... - Page 47 2.5.5 Element Assemblies and Hardware cont. ITEM PART # COMPONENT Element Kits – includes gaskets, grommets, tie wraps, screws and nuts. 200V 17.0 kW (220V 8.5kW used in some export 3-phase 4-wire WYE 826-2198 units) 826-2201 200V 18.5 kW 826-2192 208V 17.0 kW 826-2197 208V 18.5 kW...
-
Page 48: Element Tube Assemblies
2.5.6 Element Tube Assemblies ITEM PART # COMPONENT 108-0297SP Tube Assembly, Full-Vat 14kW 108-0293 Tube Assembly, Full-Vat 17 108-0298SP Tube Assembly Dual-Vat 14kW 108-0295 Tube Assembly Dual-Vat 17 810-3246 Bushing and Tube Assembly, Dual-Vat 108-0315 Bracket Assembly, LH Element Tube Support 108-0316 Bracket Assembly, RH Element Tube Support 220-0122... -
Page 49: Wiring
2.5.8 Wiring 2.5.8.1 Contactor Box Wiring Assemblies – 12-Pin Dual-Vat C-1 ITEM PART # COMPONENT 106-5980SP Contactor Box Harness Assembly Dual Vat Standard (See wiring diagrams on pages 1-35 thru 1-36.) 2.5.8.2 Contactor Box Wiring Assemblies – 12-Pin Full-Vat C-1 ITEM PART # COMPONENT... -
Page 50: Contactor Box Wiring Assemblies 6-Pin Left Element
2.5.8.3 Contactor Box Wiring Assembly – 6-Pin (Left Element) ITEM PART # COMPONENT 106-8744SP 14/17 kW Mechanical Contactor 106-7851SP High Amp Mechanical Contactor 2.5.8.4 Contactor Box Wiring Assembly – 9-Pin (Right Element) ITEM PART # COMPONENT 106-8745SP 14/17 kW Mechanical Contactor 106-7852SP High Amp Mechanical Contactor 2-17... -
Page 51: Main Wiring Harnesses
2.5.8.5 Main Wiring Harnesses 12-Pin Female Connector 15-Pin Male Connector 807-0159 (Rear of Fryer) 807-0804 (Rear of Component Box) 12-Pin Male Connector 807-0160 (Contactor Box) USED ONLY ON DUAL VAT HARNESSES FULL VAT HARNESS 807-4194 DUAL VAT HARNESS 807-4195 2-18... -
Page 52: Component Box, Filter Pump And Basket Lift Wiring Harnesses
2.5.8.6 Component Box, Filter Pump and Basket Lift Wiring Harnesses ITEM PART # COMPONENT 106-5750SP Full Vat Control Harness J4 to J2 (Standard) 106-5751SP Dual Vat Control Harness J4 to J1 and J2 (Standard) 108-0490SP Filter Pump C2 to Component Box Wiring Harness 106-5962SP Basket Lift Harness Assembly (Standard) 2.5.8.7 Component Box to Filter Pump Harness... -
Page 53: Basket Lift Harness
2.5.8.8 Basket Lift Harness 2.5.8.9 Interface Board to Controller Wiring Harness – 15-Pin PN 807-4199 SMT Controller to Interface Board Wiring Harness 2.5.8.10 3000 and ATO Wiring Harnesses ITEM PART # COMPONENT 807-4546 Controller Communication (used from Controller to Controller) 807-4655 Harness ATO RTD Extension (used from ATO RTD to ATO Board) 826-2569... -
Page 54: Filtration System Components
Filtration System Components ITEM PART # COMPONENT 823-7910 Lid, Half Size Filter Pan 810-3288 Crumb Tray, Half Size Filter Pan 810-3289 Hold-Down Ring 11.20 x 19.10, Half Size Filter Pan 812-2025 SanaGrid Filter Screen, Half Size Filter Pan 108-3872SP Pan, Filter with casters 108-6977SP Pan, Filter with casters (Only for use with Filter Leaf 810-4492) 106-8211SP... -
Page 55: Filter Pump, Motor And Associated Components
Filter Pump, Motor and Associated Components ITEM PART # COMPONENT Motor and Gasket Kit 826-1785 100V 50/60 Hz √ 826-1712 115V 50/60 Hz √ 826-1756 208V 50/60 Hz 826-1270 220-240V 50/60 Hz 826-1755 250V 50/60 Hz 826-3191 Pump and Gasket Kit, Viking 4 GPM (includes gasket and cap screws below) 816-0093 Gasket, Pump/Motor 809-1062... -
Page 56: Frypot Assemblies And Associated Parts
2.8 Frypot Assemblies and Associated Parts See Page 2-7 for Drain Valve Assembly. ITEM PART # COMPONENT 823-7889 Frypot, Full-Vat OCF with top off prior to 07/2014 823-8950 Frypot, Full-Vat OCF with top off after 06/2014 823-7886 Frypot, Full-Vat OCF no top off prior to 07/2014 823-8951 Frypot, Full-Vat OCF no top off after 06/2014 823-8017... -
Page 57: Oil Return System Components
2.9 Oil Return System Components ITEM PART # COMPONENT 108-2433 Handle Assembly, Full-Vat and Right Dual-Vat Rear Flush Complete 108-2432 Handle Assembly, Left Dual-Vat Rear Flush Complete 106-5595 Bracket Assembly, Microswitch 200-5401 Bracket, Handle Retainer 807-2103 Microswitch, Straight Lever 809-0601 Clip, Clevis 810-3887 Handle, Oil Return Left Dual Vat Rod... -
Page 58: Auto Top-Off Components
2.10 Auto Top-Off Components 2.10.1 Automatic Top-Off Board Assembly 108-2558SP 108-2557SP 208-240V Assy 120V Assy ITEM PART # COMPONENT 108-2556 Box, Assembly Auto Top Off Board 220-5679 Cover, Top Off Board Box √ 3 108-2805 PCB Board, Automatic Top Off OCF √... -
Page 59: Ato Pump Assembly
2.10.3 ATO Pump Assembly Liquid Shortening Semi/Solid Shortening JIB hose connects here. INSTALL See page 2-28 for O-RINGS inlet plumbing HERE ITEM PART # COMPONENT √ 1 108-0639 Pump, Shurflo 24VAC 810-3375 Flexline, ½” OD x 17-inch (Out to top off manifold) 811-1139 Hose, Silicone Braided (sold by the foot) 810-3578... -
Page 60: Ato Top-Off Manifolds
2.10.4 ATO Top-Off Manifolds Connects to item #10 on page 2-23 Connects to item #2 on the preceding page ITEM PART # COMPONENT 810-3896 Manifold, Top-Off Two Station Fryer 810-3897 Manifold, Top-Off Three Station Fryer 810-3898 Manifold, Top-Off Four Station Fryer √... -
Page 61: Shortening Melting Unit
2.10.5 Shortening Melting Unit ITEM PART # COMPONENT 108-3406 Assembly, Heated Shortening 108-2983 Box Assembly, Heated Shortening 108-3001 Assembly, Heated Shortening Lid 810-3957 Pan, Heated Shortening 108-3372 Cover, Shortening Box Front 810-0180 Handle √ 6 826-1392 O-Ring (Pkg. of 5) 813-0568 Plug, ⅛-inch Socket Head Pipe 823-8079... -
Page 62: Bulk Oil Relay Box And Switch
2.10.6 Bulk Oil Relay Box and Switch ITEM PART # COMPONENT 108-3409 Harness, Bulk Oil Power 108-3410 Harness, Bulk Oil Control 108-3412 Harness, Bulk Oil Switches 108-3413 Harness, Bulk Oil Communication 220-8665 Box, Bulk Oil Relay 220-8666 Cover, Bulk Oil Relay Box 807-1068 Connector, 2-pin √... -
Page 63: Bulk Oil Plumbing
2.10.7 Bulk Oil Plumbing To Oil Return Manifold To Topoff Pump Intake Elbow To Drain ITEM PART # COMPONENT √ 106-6830 Solenoid Assy 108-3368 Valve, Assy Waste Dispose (see next page for valve assembly) 807-5318 Cable, Bulk Oil Communication 810-1057 Flexline, ⅝”... -
Page 64: Bulk Oil Dispose Waste Valve
2.10.8 Bulk Oil Dispose Waste Valve ITEM PART # COMPONENT 108-3368 Valve, Dispose Waste Assembly 108-0445 Bracket, Waste Valve 220-5615 Handle, Waste Valve √ 3 807-2103 Microswitch 810-0278 Valve, ½” Ball 900-2935 Retainer, Nut Return Valve 901-2348 Cover, DV Safety Switch 902-2348 Cover, DV Safety Switch √... -
Page 65: Wiring Connectors, Pin Terminals And Power Cords
2.11 Wiring Connectors, Pin Terminals, and Power Cords ITEM PART # COMPONENT Power Cords 807-0154 100/120V–15A 3-wire, w/grounded plug 807-1685 100/208/240V–18A 3-wire, w/o plug 807-3817 208-250V/74A 3-Phase 4-wire w/plug 96” 8 awg 807-4668 208-250V/84A 3-Phase 4-wire w/plug 96” 6 awg 807-3834 208-250V/84A 3-Phase 4-wire w/plug 96”... -
Page 66: Fasteners
2.12 Fasteners ITEM PART # COMPONENT 809-0429 Bolt, ¼-inch – 20 x 2.00-inch Hex Head ZP Tap 809-0131 Bolt, ¼-inch -20 x ¾-inch Hex 809-1020 Cap Screw, 5/16-inch-18 5.50” NC Hex (Connects pump to motor.) 809-0448 Clip, Tinnerman 826-1366 Nut, 4-40 Keps Hex (Pkg. of 25) (809-0237) 826-1358 Nut, 6-32 Keps Hex (Pkg. - Page 67 THIS PAGE INTENTIONALLY LEFT BLANK...
- Page 68 Frymaster, L.L.C., 8700 Line Avenue, Shreveport, Louisiana 71106 TEL 1-318-865-1711 FAX (Tech Support) 1-318-219-7135 SERVICE HOTLINE 8196686 PRINTED IN THE UNITED STATES 1-800-551-8633 06/2018...