Crestron DM-NVX-D30 Product Manual
Dm nvx network av encoders/decoders
Hide thumbs
Also See for DM-NVX-D30:
- Configuration manual (44 pages) ,
- Design manual (42 pages) ,
- Product manual (34 pages)
Subscribe to Our Youtube Channel
Related Manuals for Crestron DM-NVX-D30
Summary of Contents for Crestron DM-NVX-D30
- Page 1 DM NVX™ Network AV Encoders/Decoders DM-NVX-E30 DM-NVX-D30 DM-NVX-E30C DM-NVX-D30C DM-NVX-D80-IOAV Product Manual Crestron Electronics, Inc.
- Page 2 Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
-
Page 3: Table Of Contents
Introduction ............................ 1 Physical Description ........................2 DM-NVX-E30 and DM-NVX-D30 ......................2 Front Panel, DM-NVX-E30 ........................ 2 Front Panel, DM-NVX-D30 ....................... 3 Rear Panel, DM-NVX-E30 and DM-NVX-D30 ................4 DM-NVX-E30C ............................5 DM-NVX-D30C ............................6 DM-NVX-D80-IOAV ..........................7 Front Panel ............................7 Rear Panel ............................. - Page 4 HDCP 2.2 Compliance ....................... 27 IGMP Snooping ........................... 28 Troubleshooting .......................... 30 Appendix: Device Discovery ...................... 32 ii • Contents Product Manual – DOC. 8425B...
-
Page 5: Introduction
IOAV also functions as a decoder only and is compatible with the Intel® OPS (Open Pluggable Specification). Compact in design, the DM-NVX-E30 and DM-NVX-D30 are designed to mount to a flat surface such as a wall. The DM-NVX-E30C and DM-NVX-D30C are designed to occupy the DMF-CI-8 card chassis. -
Page 6: Physical Description
The HDMI connection requires an appropriate adapter or interface cable to accommodate a DVI or Dual-Mode DisplayPort signal. CBL-HD-DVI interface cables are sold separately. Device control via CEC (Consumer Electronics Control) requires the use of a Crestron 3-Series® or later control system. -
Page 7: Front Panel, Dm-Nvx-D30
The HDMI connection requires an appropriate adapter or interface cable to accommodate a DVI signal. CBL-HD-DVI interface cables are sold separately. Device control via CEC requires the use of a Crestron 3-Series or later control system. Product Manual – DOC. 8425B... -
Page 8: Rear Panel, Dm-Nvx-E30 And Dm-Nvx-D30
COM: 5-pin 3.5 mm detachable terminal block; Bidirectional RS-232 port;* Up to 115.2k baud, hardware and software handshaking support Device control via IR and RS-232 requires the use of a Crestron 3-Series or later control system. 4 • DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV Product Manual – DOC. 8425B... -
Page 9: Dm-Nvx-E30C
The LAN port must connect to a 1000BASE-T switch in order to stream network video. Device control via CEC requires the use of a Crestron 3-Series or later control system. The HDMI connection requires an appropriate adapter or interface cable to accommodate a DVI or Dual-Mode DisplayPort signal. -
Page 10: Dm-Nvx-D30C
The LAN port must connect to a 1000BASE-T switch in order to stream network video. Device control via CEC requires the use of a Crestron 3-Series or later control system. The HDMI connection requires an appropriate adapter or interface cable to accommodate a DVI signal. -
Page 11: Dm-Nvx-D80-Ioav
LAN: 8-pin RJ-45 connector; 100BASE-TX/1000BASE-T Ethernet port;* Green LED indicates Ethernet link status; Amber LED indicates Ethernet activity The LAN port must connect to a 1000BASE-T switch in order to stream network video. Product Manual – DOC. 8425B DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV • 7... -
Page 12: Rear Panel
EDID (Extended Display Identification Data) • Subscriptions 7.1 surround sound audio • • Analog audio output • Crestron XiO Cloud™ service connection Enterprise-grade security • • Fan control • Automatic firmware update 8 • DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV Product Manual – DOC. 8425B... -
Page 13: Dmf-Ci-8 Chassis Details
View DM NVX Director appliance information on the Status page. The DM NVX Director section displays the following information: • DM NVX Director hostname • Domain name, number, and slot number to which the DM NVX device is assigned Product Manual – DOC. 8425B DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV • 9... -
Page 14: Stream Statistics
Statistics to Enable or Disable. To reset statistics, click Reset Statistics. For additional information, refer to the online help of the web interface. NOTE: The bit rate of the stream appears on the Stream page of the DM-NVX-D30, DM-NVX-D30C, and DM-NVX-D80-IOAV only. Stream Page - Statistics Configuration 10 •... -
Page 15: Using Simpl Windows
Using SIMPL Windows For the DM-NVX-E30 and DM-NVX-E30C, configure stream statistics in Slot-01: Stream Transmit. For the DM-NVX-D30, DM-NVX-D30C, and DM-NVX-D80-IOAV, configure stream statistics in Slot-02: Stream Receive. Trigger the <StatisticsEnabled> digital input join to enable the reporting of statistics. To disable statistics, trigger the <StatisticsDisabled>... -
Page 16: Using Simpl Windows
2. In Slot-01: Stream Transmit, set the <MulticastTTL> analog input join to the desired value (1 to 255). 3. Using the top-level programming slot, trigger the <AutomaticInitiationEnabled> digital input join. The stream automatically restarts. For additional information, refer to the SIMPL Windows help file. 12 • DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV Product Manual – DOC. 8425B... -
Page 17: Dscp (Differentiated Services Code Point)
4. Enter the desired DSCP value (0 to 63). 5. Set Auto Initiation to Enabled. The stream automatically restarts. NOTE: Deselecting the DSCP checkbox returns the DSCP value to the default setting. Stream Page - DSCP Configuration Product Manual – DOC. 8425B DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV • 13... -
Page 18: Edid (Extended Display Identification Data)
Configure EDID on the HDMI INPUT page. In the EDID section of the page, select the desired EDID. For additional information, refer to the online help of the web interface. HDMI INPUT Page - EDID Configuration 14 • DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV Product Manual – DOC. 8425B... -
Page 19: Subscriptions
Subscriptions NOTE: Subscription configuration is applicable to the DM-NVX-D30, DM-NVX-D30C, and DM-NVX-D80-IOAV only. Subscription of a DM NVX encoder to a DM NVX decoder sets up Real Time Streaming Protocol (RTSP) negotiation between the DM NVX decoder and the DM NVX encoder. -
Page 20: Using Simpl Windows
Dolby® TrueHD, Dolby Atmos®, DTS HD®, DTS:X® and uncompressed linear PCM audio formats. NOTE: The DM-NVX-D30, DM-NVX-D30C, and DM-NVX-D80-IOAV cannot accept downmixed audio from a DM-NVX-351 or DM-NVX-351C transmitter. To configure 7.1 surround sound audio, set the desired EDID (refer to "EDID" on page 14). -
Page 21: Analog Audio Output
Using SIMPL Windows Using the top-level programming slot for the DM NVX device, set the <AnalogAudioOutputVolume> analog input join to the desired volume. For additional information, refer to the SIMPL Windows help file. Product Manual – DOC. 8425B DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV • 17... -
Page 22: Usb 2.0 Routing
Crestron DM NVX products are engineered to deliver maximum compatibility with the widest possible range of USB products. Crestron does not guarantee that all USB products are compatible with DM NVX products. Consult the DM NVX System Design Guide, Doc. -
Page 23: Using The Web Interface
In the Remote Device ID text box, enter the MAC address of a single remote extender. If Transport Mode is set to Layer 3: • In the Remote Device ID text box, enter the IP address of a single remote extender. Product Manual – DOC. 8425B DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV • 19... -
Page 24: Using Simpl Windows
One DM-NVX-D80-IOAV device functions as the remote extender (REX) with host port functionality for connection to a USB mouse, keyboard, or other peripheral device. Continue with the following steps for each DM NVX device. 20 • DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV Product Manual – DOC. 8425B... - Page 25 5. Do either of the following: • Trigger the <Pair> digital input join on each DM NVX device (LEX and REX). • Trigger the <AutomaticUSBPairingEnabled> digital input join on each DM NVX device (LEX and REX). Product Manual – DOC. 8425B DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV • 21...
-
Page 26: Crestron Xio Cloud Service Connection
Connection to the Crestron XiO Cloud service can be enabled or disabled using the web interface. Configure the connection to the Crestron XiO Cloud service on the Device page. In the Cloud Settings section of the page, set Cloud Configuration Service Connection to Enabled (default setting) or Disabled. -
Page 27: Enterprise-Grade Security
LAN. Configure IEEE 802.1X authentication in the 802.1x Configuration section of the Network page. For detailed information, refer to the online help of the web interface. Network Page – IEEE 802.1X Configuration Product Manual – DOC. 8425B DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV • 23... -
Page 28: Authentication Management
Active Directory® credential management groups. Predefined access levels can also be assigned. Configure authentication management in the Authentication Management section of the Device page. For detailed information, refer to the online help of the web interface. Device Page – Authentication Management 24 • DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV Product Manual – DOC. 8425B... -
Page 29: Fan Control
Device Page – Fan Control Using SIMPL Windows Using the top-level programming slot for the DM-NVX-D30, set the <FanControl> analog input join to the desired setting. The <FanControl_F> analog output join reports the fan mode of operation. The <FanStatus_F> analog output join reports the fan status. -
Page 30: Automatic Firmware Update
A DM NXV device can be automatically updated with the latest firmware at scheduled intervals. To configure automatic firmware update: Using the Crestron Auto Update Tool, generate a manifest file (*. mft). The file is placed on an FTP (File Transfer Protocol) or SFTP (Secure File Transfer Protocol) server. -
Page 31: Hdcp 2.2 Compliance
HDCP matters only when the source demands HDCP. If the source demands HDCP 2, then every device in the signal path must support HDCP 2. • There are no issues related to HDCP 2 and cabling—all cables are compatible. Product Manual – DOC. 8425B DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV • 27... -
Page 32: Igmp Snooping
(RFC 1112), there is a loss of information when forwarding solely on the destination MAC address. For example, IP addresses 224.0.0.123 and 239.128.0.123 and similar IP multicast addresses all map to MAC address 01-00-5e-00-00-7b for Ethernet. 28 • DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV Product Manual – DOC. 8425B... - Page 33 If the network switch supports IGMP fast leave, enable the configuration at the port, global, or VLAN level. • If the network switch supports PIM snooping, enable the configuration to prevent flooding IP multicast traffic toward multicast router (mrouter) ports. Product Manual – DOC. 8425B DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV • 29...
-
Page 34: Troubleshooting
Troubleshooting The following table provides troubleshooting information. If further assistance is required, contact a Crestron customer service representative. DM NVX Encoder/Decoder Troubleshooting 4K60 4:4:4 2-channel non-HDR or The display device is not Configure the display device properly. 4K60 4:4:4 2-channel HDR video configured properly. - Page 35 • On the Device page of the web interface, click the Restore button. • From the Tools menu in the Crestron Toolbox software, select Text Console and issue the restore command. • Power cycle the device 10 times. After the tenth power cycle, wait until the device boots and then press the SETUP button for 5 seconds.
-
Page 36: Appendix: Device Discovery
The security software running on the computer may send a program alert • regarding the attempt of the Crestron Toolbox software to connect to the network. Allow the connection so that the Device Discovery Tool can be used. The DM NVX device is discovered and is listed in the device list on the left side of the screen. - Page 37 The user name and password are case sensitive. 7. Click Sign In. The Status page of the DM NVX device opens. For additional information, refer to the online help of the web interface. Product Manual – DOC. 8425B DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV • 33...
- Page 38 This page is intentionally left blank. 34 • DM-NVX-E30(C)/DM-NVX-D30(C)/DM-NVX-D80-IOAV Product Manual – DOC. 8425B...
- Page 40 Crestron Electronics, Inc. Product Manual – DOC. 8425B 15 Volvo Drive, Rockleigh, NJ 07647 (2053136) Tel: 888.CRESTRON 11/01/19 Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.
Need help?
Do you have a question about the DM-NVX-D30 and is the answer not in the manual?
Questions and answers