Symmons 4200TRMTC Installation & Operation Instructions

Symmons 4200TRMTC Installation & Operation Instructions

With ta-10 flow control spindle & t-12a cap

Advertisement

Oxford Trim Series
Oxford Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly
Installation & Operation Instructions
Model Numbers
TRIM ONLY
4200-TRM
Shower Valve Trim
4201-TRM
Shower Trim
4202-TRM
Tub/Shower Trim
4203-TRM
Hand Shower Trim
4205-TRM
Shower/Hand Shower Trim
4206-TRM
Tub/Shower/Hand Shower Trim
Compliance
ASME A112.18.1/CSA B125.1
Warranty
Limited Lifetime - to the original end purchaser in consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete warranty information.
Go to www.symmons.com/register to register your Symmons product.
Oxford
TRIM, TA-10, T-12A
4200TRMTC
Shower Valve Trim
4201TRMTC
Shower Trim
4202TRMTC
Tub/Shower Trim
4203TRMTC
Hand Shower Trim
4205TRMTC
Shower/Hand Shower Trim
4206TRMTC
Tub/Shower/Hand Shower Trim
T-12A
TA-10
®
4200-TRM
4200TRMTC
4203-TRM
4203TRMTC
4201-TRM
4202-TRM
4201TRMTC
4202TRMTC
4205-TRM
4206-TRM
4205TRMTC
4206TRMTC

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4200TRMTC and is the answer not in the manual?

Questions and answers

Summary of Contents for Symmons 4200TRMTC

  • Page 1 4205TRMTC 4206TRMTC Compliance • ASME A112.18.1/CSA B125.1 Warranty Limited Lifetime - to the original end purchaser in consumer/residential installations. 5 Years - for industrial/commercial installations. Refer to www.symmons.com/warranty for complete warranty information. Go to www.symmons.com/register to register your Symmons product.
  • Page 2 1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (3mm) Drill Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions Measurements FIGURE 2 6-1/2", 165 mm 9-5/8", 245 mm 3-7/8", 98 mm Male 1/2" IPS thread must protrude 1/2" from finished wall 6", 152 mm right or left 77", 1956...
  • Page 3 3. Parts Breakdown (Model Numbers Ending in TRMTC) Replacement Parts LIMIT STOP Item Description Part Number SCREW Cap Assy. T-12A Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system.
  • Page 4 For more information, go to www.P65Warnings.ca.gov. ■ ■ ■ ■ Symmons Industries, Inc. 31 Brooks Drive Braintree, MA 02184 Phone: (800) 796-6667 Fax: (800) 961-9621 ■ ■ ■ ■ Copyright © 2019 Symmons Industries, Inc. symmons.com gethelp@symmons.com ZV-3285 REV A 062819...

This manual is also suitable for:

4200-trmOxford trim series4201-trm4201trmtc4202-trm4202trmtc ... Show all

Table of Contents