Advertisement
6 MENU button
Activates/deactivates the display of the MAIN MENU
(☞ "Menu Operations" on page 13).
7 COLOR OFF button/lamp
Displays only the luminance signal.
●
This function does not work for RGB input signals.
8 1:1 button/lamp
Displays the picture in the original resolution of the input signal.
●
The aspect ratio of the picture may change depending on the
input signal.
9 AREA MARKER button/lamp
Displays/hides the area marker.
●
Select the style of the area marker in "MARKER" of the MAIN
MENU (☞ page 15).
●
This function does not work when displaying the picture in the
1:1 mode.
●
This function works only when displaying the picture in 16:9
aspect ratio.
●
This function does not work when "AREA MARKER" or "R-AREA
MARKER" is set to "OFF" in "MARKER."
p SAFETY MARKER button/lamp
Displays/hides the safety marker.
●
Adjust the area of the safety marker in "MARKER" of MAIN
MENU (☞ page 15).
●
This function does not work when displaying the picture in the
1:1 mode.
●
This function does not work when "SAFETY MARKER" or "R-
SAFETY MARKER" is set to "OFF" in "MARKER."
q SCREENS CHECK button/lamp
Displays only the selected element (R, G, or B) of the video signal.
●
This function does not work for RGB input signals.
●
Each time you press this button, the picture changes in the
following order.
RGB (Normal screen)
Blue screen
w ASPECT button/lamp
Changes the aspect ratio of the picture from 4:3 to 16:9 when the
picture of 16:9 aspect ratio is squeezed into 4:3 format signal.
●
To return to 4:3, press the button again.
●
This function does not work when displaying the picture in the
1:1 mode.
e SCOPE button/lamp
Displays/hides the indication of the wave form monitor and
vector scope (☞ "SCOPE SETTING" on page 17).
●
Each time you press this button, the window changes in the
following order.
No display
Vectorscope
r T.C. (time code) button/lamp
Activates/deactivates the display of the time data (time code)
contained in the SDI signal (☞ "On the Information Display" on
page 11).
●
Select the time code type in "INFORMATION" of SET-UP MENU
(☞ page 20).
Red screen
Green screen
Wave form monitor
t INPUT SELECT buttons/lamps
Selects an input.
SDI 1:
Input from the E. AUDIO SDI/HD SDI/
SD SDI (IN 1) terminal
SDI 2:
Input from the E. AUDIO SDI/HD SDI/
SD SDI (IN 2) terminal
DUAL LINK:
Input from the E. AUDIO SDI /HD SDI/
SD SDI (IN 1, IN 2) terminals
DVI:
Input from the DVI-D (HDCP) terminal
COMPO.:
Input from the COMPO. terminals
VIDEO:
Input from the VIDEO terminal
●
The lamp for the selected input lights.
●
When "SDI DUAL LINK" is set to "ON" in MAIN MENU, press
SDI 1 or SDI 2 to select DUAL LINK
y Power lamp
Off:
The power is turned off
Green:
The monitor is on
Orange:
The monitor is turned off (standby)
Orange blinking: P.SAVE (Power saving) mode ("NO SYNC
ACTION" in "SYNC FUNCTION") (☞ page
17)
u DC lamp
When the DC power voltage is being lowered due to the battery
consumption, the lamp changes to orange from green. When the
voltage becomes lower than a certain level, the monitor
automatically turns off and the lamp turns to red.
●
Make sure to turn off the POWER switch and DC switch on the
rear panel before replacing the battery.
●
The length of time that the lamp lights in orange differs
depending on the type of battery or the battery condition. It is
recommended to replace the battery when the lamp turns to
orange.
i
button
Turns on and off (on standby) the monitor.
●
To turn off the monitor completely, turn off the POWER switch
(☞ e on page 10)
and DC switch
(☞ page 14)
.
(☞ p on page 10).
9
Advertisement
