Interrupt generation via stm trigger, aurix tc2xx microcontroller training (10 pages)
Summary of Contents for Infineon Cypress CYBLE-212020-01
Page 1
The document following this cover page is marked as “Cypress” document as this is the company that originally developed the product. Please note that Infineon will continue to offer the product to new and existing customers as part of the Infineon product portfolio.
Page 2
CYBLE-212020-01 EZ-BLE™ Creator Module EZ-BLE™ Creator Module General Description RX current consumption of 16.4 mA (radio only) ■ Low power mode support ■ The CYBLE-212020-01 is a fully certified and qualified module Deep Sleep: 1.3 µA with watch crystal oscillator (WCO) on ...
Page 3
CYBLE-212020-01 More Information Cypress provides a wealth of data at www.cypress.com to help you to select the right module for your design, and to help you to quickly and effectively integrate the module into your design. Overview: Knowledge Base Article ■...
Page 4
CYBLE-212020-01 Two Easy-To-Use Design Environments to Get You Started Quickly ® PSoC Creator™ Integrated Design Environment (IDE) PSoC Creator is an Integrated Design Environment (IDE) that enables concurrent hardware and firmware editing, compiling and debugging of PSoC 3, PSoC 4, PSoC 5LP, PSoC 4 Bluetooth LE, and EZ-BLE module systems with no code size limitations. PSoC peripherals are designed using schematic capture and simple graphical user interface (GUI) with over 120 pre-verified, production-ready PSoC Components™.
CYBLE-212020-01 Overview Module Description The CYBLE-212020-01 module is a complete module designed to be soldered to the applications main board. Module Dimensions and Drawing Cypress reserves the right to select components (including the appropriate Bluetooth LE device) from various vendors to achieve the Bluetooth LE module functionality.
Page 7
CYBLE-212020-01 Figure 1. Module Mechanical Drawing Top View (View from Top) Side View Bottom View (Seen from Bottom) Note 1. No metal should be located beneath or above the antenna area. Only bare PCB material should be located beneath the antenna area. For more information on recommended host PCB layout, see Figure Figure...
CYBLE-212020-01 Pad Connection Interface As shown in the bottom view of Figure 1 on page 6, the CYBLE-212020-01 connects to the host board via solder pads on the back side of the module. Table 2 Figure 2 detail the solder pad length, width, and pitch dimensions of the CYBLE-212020-01 module. Table 2.
CYBLE-212020-01 Recommended Host PCB Layout Figure Figure Figure 6, and Table 3 provide details that can be used for the recommended host PCB layout pattern for the CYBLE-212020-01. Dimensions are in millimeters unless otherwise noted. Pad length of 1.27 mm (0.635 mm from center of the pad on either side) shown in Figure 6 is the minimum recommended host pad length.
Page 10
CYBLE-212020-01 Table 3 provides the center location for each solder pad on the CYBLE-212020-01. All dimensions are referenced to the center of the solder pad. Refer to Figure 6 for the location of each module solder pad. Table 3. Module Solder Pad Location Figure 6.
CYBLE-212020-01 Digital and Analog Capabilities and Connections Table 4 details the solder pad connection definitions and available functions for each connection pad. Table 4 lists the solder pads on CYBLE-212020-01, the Bluetooth LE device port-pin, and denotes whether the function shown is available for each solder pad. Each ✓...
CYBLE-212020-01 Power Supply Connections and Recommended External Components Power Connections External Component Recommendation The CYBLE-212020-01 contains two power supply connections, In either connection scenario, it is recommended to place an VDD and VDDR. The VDD connection supplies power for both external ferrite bead between the supply and the module digital and analog device operation.
Page 13
CYBLE-212020-01 Figure 8. Recommended Host Schematic for an Independent Supply Option Independent Power Supply Option(Seen from Bottom) Document Number: 002-12597 Rev. *H Page 12 of 40...
Page 14
CYBLE-212020-01 The CYBLE-212020-01 schematic is shown in Figure Figure 9. CYBLE-212020-01 Schematic Diagram Document Number: 002-12597 Rev. *H Page 13 of 40...
CYBLE-212020-01 Critical Components List Table 5 details the critical components used in the CYBLE-212020-01 module. Table 5. Critical Component List Component Reference Designator Description Silicon 56-pin QFN PSoC 4 Bluetooth LE Crystal 24.000 MHz, 12PF Crystal 32.768 kHz, 12.5PF Antenna Design Table 6 details trace antenna used in the CYBLE-212020-01 module.
CYBLE-212020-01 Electrical Specifications Table 7 details the absolute maximum electrical characteristics for the Cypress Bluetooth LE module. Table 7. CYBLE-212020-01 Absolute Maximum Ratings Parameter Description Units Details/Conditions Analog, digital, or radio supply relative to V –0.5 – Absolute maximum DDD_ABS Direct digital core voltage input relative to V –0.5 –...
Page 17
CYBLE-212020-01 Table 9. CYBLE-212020-01 DC Specifications (continued) Parameter Description Units Details/Conditions Execute from flash; CPU at 12 MHz – – – T = –40 °C to 85 °C T = 25 °C, Execute from flash; CPU at 24 MHz – –...
CYBLE-212020-01 Table 10. AC Specifications Parameter Description Units Details/Conditions 1.71 V V 5.5 V CPU frequency – Wakeup from Sleep mode – – µs Guaranteed by characterization SLEEP 24-MHz IMO. Guaranteed by Wakeup from Deep-Sleep mode – – µs DEEPSLEEP characterization Wakeup from Hibernate mode –...
CYBLE-212020-01 Table 12. GPIO AC Specifications Parameter Description Units Details/Conditions Rise time in Fast-Strong mode – 3.3-V V = 25 pF RISEF LOAD Fall time in Fast-Strong mode – 3.3-V V = 25 pF FALLF LOAD Rise time in Slow-Strong mode –...
Page 20
CYBLE-212020-01 Table 16. XRES AC Specifications Parameter Description Units Details/Conditions Reset pulse width – – µs – RESETWIDTH Temperature Sensor Table 17. Temperature Sensor Specifications Parameter Description Units Details/Conditions Temperature-sensor accuracy –5 ±1 °C –40 to +85 °C SENSACC SAR ADC Table 18.
Page 21
CYBLE-212020-01 Table 19. SAR ADC AC Specifications Parameter Description Units Details/Conditions A_PSRR Power-supply rejection ratio – – Measured at 1-V reference A_CMRR Common-mode rejection ratio – – A_SAMP Sample rate – – Msps Fsarintref SAR operating speed without external – –...
CYBLE-212020-01 Digital Peripherals Timer Table 20. Timer DC Specifications Parameter Description Units Details/Conditions Block current consumption at 3 MHz – – µA 16-bit timer TIM1 Block current consumption at 12 MHz – – µA 16-bit timer TIM2 Block current consumption at 48 MHz –...
Page 23
CYBLE-212020-01 Counter Table 22. Counter DC Specifications Parameter Description Units Details/Conditions Block current consumption at 3 MHz – – 16-bit counter µA CTR1 Block current consumption at 12 MHz – – µA 16-bit counter CTR2 Block current consumption at 48 MHz –...
CYBLE-212020-01 LCD Direct Drive Table 26. LCD Direct Drive DC Specifications Parameter Description Units Details/Conditions Operating current in low-power mode – 17.5 – µA 16 × 4 small segment LCDLOW display at 50 Hz LCD capacitance per segment/common driver – 5000 LCDCAP Long-term segment offset...
CYBLE-212020-01 Table 34. Fixed SPI Master Mode AC Specifications Parameter Description Units Details/Conditions MOSI valid after SCLK driving edge – – – MISO valid before SCLK capturing edge – – Full clock, late MISO sampling Full clock, late MISO sampling used Previous MOSI data hold time –...
CYBLE-212020-01 System Resources Power-on-Reset (POR) Table 38. POR DC Specifications Parameter Description Units Details/Conditions Rising trip voltage 0.80 – 1.45 – RISEIPOR Falling trip voltage 0.75 – 1.40 – FALLIPOR Hysteresis – – IPORHYST Table 39. POR AC Specifications Parameter Description Units Details/Conditions...
CYBLE-212020-01 SWD Interface Table 44. SWD Interface Specifications Parameter Description Units Details/Conditions 3.3 V V 5.5 V SWDCLK 1/3 CPU clock frequency F_SWDCLK1 – – 1.71 V V 3.3 V SWDCLK 1/3 CPU clock frequency F_SWDCLK2 –...
CYBLE-212020-01 Bluetooth LE Subsystem Table 50. Bluetooth LE Subsystem Details/ Parameter Description Units Conditions RF Receiver Specification RXS, IDLE RX sensitivity with idle transmitter – –89 – RX sensitivity with idle transmitter – –91 – Guaranteed by design excluding Balun loss simulation RXS, DIRTY RX sensitivity with dirty transmitter...
CYBLE-212020-01 Table 50. Bluetooth LE Subsystem (continued) Details/ Parameter Description Units Conditions RXSE1 Receiver spurious emission – – –57 100-kHz measurement 30 MHz to 1.0 GHz bandwidth ETSI EN300 328 V1.8.1 RXSE2 Receiver spurious emission – – –47 1-MHz measurement 1.0 GHz to 12.75 GHz bandwidth ETSI EN300 328 V1.8.1...
Page 30
CYBLE-212020-01 Table 50. Bluetooth LE Subsystem (continued) Details/ Parameter Description Units Conditions ITX_RF, 0dBm Radio TX current at 0 dBm excluding – 14.2 – Guaranteed by design Balun loss simulation ITX,-3dBm TX current at –3-dBm setting (PA4) – 15.5 – ITX,-6dBm TX current at –6-dBm setting (PA3) –...
CYBLE-212020-01 Environmental Specifications Environmental Compliance This Cypress Bluetooth LE module is built in compliance with the Restriction of Hazardous Substances (RoHS) and Halogen Free (HF) directives. The Cypress module and components used to produce this module are RoHS and HF compliant. RF Certification The CYBLE-212020-01 module will be certified under the following RF certification standards at production release.
CYBLE-212020-01 Regulatory Information FCC NOTICE: The device CYBLE-212020-01 complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. Transmitter operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
CYBLE-212020-01 ISED Innovation, Science and Economic Development Canada (ISED) Certification CYBLE-212020-01 is licensed to meet the regulatory requirements of Innovation, Science and Economic Development Canada (ISED). License: IC: 7922A-2011 Manufacturers of mobile, fixed, or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits.
CYBLE-212020-01 MIC Japan CYBLE-212020-01 is certified as a module with type certification number 203-JN0509. End products that integrate CYBLE-212020-01 do not need additional MIC Japan certification for the end product. End product can display the certification label of the embedded module. KC Korea CYBLE-212020-01 is certified for use in Korea with certificate number MSIP-CRM-Cyp-2011.
CYBLE-212020-01 Packaging Table 52. Solder Reflow Peak Temperature Module Part Number Package Maximum Peak Temperature Maximum Time at PeakTemperature No. of Cycles CYBLE-212020-01 31-pad SMT 260 °C 30 seconds Table 53. Package Moisture Sensitivity Level (MSL), IPC/JEDEC J-STD-2 Module Part Number Package CYBLE-212020-01 31-pad SMT...
Page 36
CYBLE-212020-01 Figure 12 details reel dimensions used for the CYBLE-212020-01. Figure 12. Reel Dimensions The CYBLE-212020-01 is designed to be used with pick-and-place equipment in an SMT manufacturing environment. The center-of-mass for the CYBLE-212020-01 is detailed in Figure Figure 13. CYBLE-212020-01 Center of Mass (Seen from Top) Document Number: 002-12597 Rev.
CYBLE-212020-01 Ordering Information Table 54 lists the CYBLE-212020-01 part number and features. Table 55 lists the reel shipment quantities for the CYBLE-212020-01. Table 54. Ordering Information Flash 12-Bit Part Number Speed Size CapSense SCB TCPWM LCD Package Packing Certified (MHz) (KB) CYBLE-212020-01 1 Msps Yes...
CYBLE-212020-01 Acronyms Acronym Description Bluetooth Low Energy Bluetooth SIG Bluetooth Special Interest Group European Conformity Canadian Standards Association electromagnetic interference electrostatic discharge Federal Communications Commission GPIO general-purpose input/output Industry Canada integrated design environment Korea Certification Ministry of Internal Affairs and Communications (Japan) printed circuit board receive QDID...
CYBLE-212020-01 Document History Page Document Title: CYBLE-212020-01, EZ-BLE™ Creator Module Document Number: 002-12597 Submission Revision Description of Change Date 5285698 05/26/2016 Preliminary datasheet for CYBLE-212020-01 module. 5418841 08/31/2016 Changed status from Preliminary to Final. Updated General Description: Replaced “Bluetooth 4.1” with “Bluetooth 4.2”. Updated Power Consumption:...
Page 40
CYBLE-212020-01 Document History Page (continued) Document Title: CYBLE-212020-01, EZ-BLE™ Creator Module Document Number: 002-12597 Submission Revision Description of Change Date 7135596 05/07/2021 Updated General Description: Updated description. Updated Module Description: Updated description. Updated hyperlinks. Updated Two Easy-To-Use Design Environments to Get You Started Quickly: Updated PSoC®...
CYBLE-212020-01 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. ® Products PSoC Solutions ®...