Table of Contents
Advertisement
3.3.3
Ethernet connectors
Gigabit Ethernet Port #0 - CN4
Pin
Signal
Pin
1
GBE0_MDI0+
2
GBE0_MDI0-
3
GBE0_MDI1+
4
GBE0_MDI2+
Optional Gigabit Ethernet Port #1 - CN3
Pin
Signal
Pin
1
GBE1_MDI0+
2
GBE1_MDI0-
3
GBE1_MDI1+
4
GBE1_MDI2+
Ethernet (10/100Mbps) Networks. They will configure automatically to work with the existing network.
Please be aware that they will work in Gigabit mode only in case that they are connected to Gigabit Ethernet switches/hubs/routers. For the connection, cables
category Cat5e or better are required. Cables category Cat6 are recommended for noise reduction and EMC compatibility issues, especially when the length of the
cable is significant.
GBEx_MDI0+/GBEx_MDI0-: Ethernet Controller #x Media Dependent Interface (MDI) I/O differential pair #0. It is the first differential pair in Gigabit Ethernet mode, and
the Transmit differential pair in 10/100 Mbps modes.
GBEx_MDI1+/GBEx_MDI1-: Ethernet Controller #x Media Dependent Interface (MDI) I/O differential pair #1. It is the second differential pair in Gigabit Ethernet mode,
and the Receive differential pair in 10/100 Mbps modes.
GBEx_MDI2+/GBEx_MDI2-: Ethernet Controller #x Media Dependent Interface (MDI) I/O differential pair #2. It is the third differential pair in Gigabit Ethernet mode; it
is not used in 10/100Mbps modes.
GBEx_MDI3+/GBEx_MDI3-: Ethernet Controller #x Media Dependent Interface (MDI) I/O differential pair #3. It is the fourth differential pair in Gigabit Ethernet mode; it
is not used in 10/100Mbps modes.
CQ7-D59
CQ7-D59 - Rev. First Edition: 1.0 - Last Edition: 1.1 - Author: S.O. - Reviewed by S.B. Copyright © 2021 SECO S.p.A.
On board, there can be up to two Gigabit Ethernet connections,
for the use of up to two different LANs.
The first Gigabit Ethernet is always available, while the second
Signal
Gigabit Ethernet interface is optional (it depends on the version
5
GBE0_MDI2-
of CQ7-D59 module purchased).
6
GBE0_MDI1-
CN4 provide direct access to the Gigabit Ethernet signals
directly managed by the Qseven
7
GBE0_MDI3+
interface, available on connector CN3, is managed by a dedicated Intel
8
GBE0_MDI3-
interfaced to PCI-express lane #1 (the carrier board can also be configured to use PCI-express
lane #2, if necessary).
Please be aware that only Qseven
Signal
second Gigabit Ethernet interface.
5
GBE1_MDI2-
On the connectors there are also two bicolour Green/Yellow LEDs: LED1 (Left LED) shows
10/100 or 1000 connection: green means 100Mbps connection, yellow means 1000Mpbs
6
GBE1_MDI1-
connection, when the LED is Off then 10Mpbs or no connection is available. LED2 (Right LED)
7
GBE1_MDI3+
shows ACTIVITY presence.
8
GBE1_MDI3-
These two interfaces are compatible both with Gigabit Ethernet (1000Mbps) and with Fast
®
modules, while the second optional Gigabit Ethernet
®
modules offering PCI-Express lane #1 or #2 can exploit the
®
I210 controller,
29
Advertisement
Table of Contents
