Connection Of Water Supply - Nu-Vu QBT-3/9 Manual

RECEIPT, INSTALLATION AND START-UP

Connection of Water Supply - -

IMPORTANT: THIS UNIT NEEDS TO BE INSTALLED WITH ADEQUATE BACKFLOW
PROTECTION TO COMPLY WITH APPLICABLE FEDERAL, STATE AND LOCAL CODES.
IMPORTANT: THIS UNIT REQUIRES A SCREEN OF AT LEAST 100 MESH TO BE
INSTALLED IMMEDIATELY UPSTREAM OF ALL CHECK VALVE TYPE BACKFLOW
PREVENTERS USED FOR WATER SUPPLY PROTECTION. THE SCREEN SHALL BE
ACCESSIBLE AND REMOVABLE FOR CLEANING OR REPLACEMENT.
®
NU-VU strongly recommends that SOFT WATER ONLY be used in any unit requiring a water supply. Also, a good quality
water filter must be installed in-line between the unit connection and the water supply to guard against clogging and mineral
build-up in the components, one is included with your QBT-3/9. This is extremely important in areas having hard water. The
water filter head is installed on the rear of the equipment, the filter cartridge is shipped inside the proofer.
A. Run 1/4" (6.35mm) OD tubing from the water supply line to the unit location. Allow some slack in the tubing for
final unit positioning and any future service requirements. Avoid any kinks or strains on the tubing, and position
the tubing where it will not be damaged in any way.
B. The tubing end that attaches to the back of the unit must not be damaged or deformed in any way. The cut end
should be cut straight and clean with no deforming of the tubing. All burrs and sharp or rough edges should be
removed to ensure a proper and leak-free connection.
C. Position the tubing so that it runs straight into the intake Water Fitting [79] on the rear of the unit. Be careful not to
kink the tubing if you bend it, and do not bend the tubing within two (2) inches of the cut end.
D. Push the end of the tubing all the way into the intake Water Fitting [79] (approximately 1/2" (12.7mm))
E. Install the filter cartridge by removing the protective cap from the top of cartridge, ensure that the two o-rings are
in place, then lift the cartridge into the filter head and rotate the cartridge 1/4 turn anti or counter clockwise until it
comes to a stop.
F. Push the unit back into place and set the brakes on the front Casters.
G. The Proofer compartment of the NU-VU
Proofer Door. Please install the included Drain Pan [77] in the bracket under the Proofer and install the Drip
Trough [72] on the front of the unit under the Proofer door.
Careful attention to these simple procedures will help to ensure an installation without leaks. If you have any questions or
problems, please call the NU-VU
NOTE: Your QBT-3/9 is equipped with a Drain in the floor of the Proofer compartment. This Drain prevents the
accumulation of excess water. Please slide the included Drain Pan [77] into the bracket under the Proofer Door to
catch any draining water.
IMPORTANT: IMPROPER INSTALLATION, MISUSE, OR OTHER FAILURE TO FOLLOW
THESE INSTRUCTIONS MAY CAUSE SEVERE EQUIPMENT DAMAGE OR PERSONAL
INJURY, AND MAY ALSO VOID ALL OR PART OF YOUR NU-VU
* * * Notice * * *
National Sanitation Foundation (NSF) guidelines require that all interior parts be removable
without the use of tools. This equipment has been factory assembled to safely accommodate
rough handling through shipment, delivery and original installation. After any maintenance,
cleaning or required service work the interior sheet metal parts should be reassembled and
fastened hand-tight only, but still be tight enough to prevent any rattle or movement of parts.
®
NU-VU FOOD SERVICE SYSTEMS
6
page
®
QBT-3/9 is equipped with a bottom drain centered directly under the
®
Service Department at (800) 338-9886.
®
YOUR NU-VU QBT-3/9 SHOULD NOW BE
READY FOR ITS INITIAL START-UP!
Sales Fax (906) 863-5889 ♦ Service Fax (906) 863-6322
QBT-3/9 OWNER'S MANUAL
®
WARRANTY!
MENOMINEE, MICHIGAN 49858-1029
(906) 863-4401 ♦ (800) 338-9886