Advertisement
Table of Contents
- 1 Important Safety Information
- 2 General Power Tool Safety Warnings
- 3 Vibration Safety
- 4 Extension Cords
- 5 Specifications
- 6 Charging the Battery Pack
- 7 Instructions for Putting into Use
- 8 Operating Instructions
- 9 Maintenance and Servicing
- 10 Before each Use
- 11 After Use
- 12 Parts LIST - ACCESSORIES
- 13 Please READ the Following Carefully
- 14 Parts List
- 15 Assembly Diagram
- 16 Limited 90-Day Warranty
- Download this manual
SET up AnD OpERATIng InSTRuCTIOnS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThIS MAnuAL.
©
Copyright
2005 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of Harbor
Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements,
actual product may differ slightly from the product described herein.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 10e
9.6V CORDLESS
ROTARY TOOL KIT
Model
®
. All rights reserved. No portion of this manual or any artwork
92880
Advertisement
Table of Contents
Related Manuals for Chicago Electric 92880
Summary of Contents for Chicago Electric 92880
- Page 1 Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. For technical questions or replacement parts, please call 1-800-444-3353. Manual Revised 10e Model 92880 ® . All rights reserved. No portion of this manual or any artwork...
-
Page 2: Important Safety Information
Do not abuse the cord. never use the cord for carrying, pulling or unplugging the Transformer or Charger Base. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. REV 10e SKU 92880... - Page 3 Eye protection must be ANSI-approved and breathing protection REV 10e SKU 92880 For technical questions, please call 1-800-444-3353. must be NIOSH-approved for the specific hazards in the work area. power tool use and care Do not force the power tool.
- Page 4 After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. REV 10e SKU 92880...
- Page 5 The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. REV 10e SKU 92880 For technical questions, please call 1-800-444-3353. Do not operate the power tool near flammable materials. Sparks could ignite these materials.
-
Page 6: Vibration Safety
Use tools with the lowest vibration when there is a choice between different processes. Include vibration-free periods each day of work. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work. REV 10e SKU 92880... -
Page 7: Extension Cords
They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters REV 10e SKU 92880 For technical questions, please call 1-800-444-3353. Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. -
Page 8: Specifications
120 VAC, 60 Hz power supply only. Connect the Charger Base to the Transformer (24), by plugging it in as shown in Figure 2. Plug the Transformer (24) into a 120 VAC wall outlet. REV 10e SKU 92880... -
Page 9: Instructions For Putting Into Use
Remove the battery pack from the tool by pulling straight out. REV 10e SKU 92880 For technical questions, please call 1-800-444-3353. InSTRuCTIOnS FOR puTTIng InTO uSE Read the EnTIRE IMpORTAnT... - Page 10 Flexible Shaft Attachment (26). Remove any bits that might be installed. Remove the Collet Lock Nut and the Collet. Remove the Collar or LED Collar from the tool Body by turning it counterclockwise. REV 10e SKU 92880...
- Page 11 Place the collet into the end of the Flexible Shaft Handle. Place the Collet Locking Nut over the bit, and tighten it by REV 10e SKU 92880 For technical questions, please call 1-800-444-3353. Installing or Removing Collars 1. To install the LED Lighted Attachment,...
-
Page 12: Operating Instructions
Page 12 For technical questions, please call 1-800-444-3353. Store the tool, its battery, and its bits and attachments in their case in a safe location. Dispose of used batteries properly. Consult your local hazardous waste authority for disposal guidelines. SKU 92880... -
Page 13: Maintenance And Servicing
A plastic storage case has been provided for safe storage of your Rotary Tool and its bits, parts and accessories. Always SKU 92880 For technical questions, please call 1-800-444-3353. store your tool and its accessories in the case provided. -
Page 14: Parts List - Accessories
2-Piece Buffing Wheel Set 4-Piece Sanding Drum Set 36-Piece Sanding Disc Set & 3-Piece Cutoff Wheel Set 2-Piece Drill Bit Set Flat Wrench 2-Piece Diamond Burr Set Square Stone Dresser 2-Piece Brass Collet Set DIAgRAM - ACCESSORIES REV 10e SKU 92880... -
Page 15: Parts List
Battery Cover Battery Release Tab Back - Moving Spring End Cover Hanger LED Light Attachment Transformer Charger Base Flexible Shaft Attachment REV 10e SKU 92880 For technical questions, please call 1-800-444-3353. pARTS LIST Qty. ASSEMBLY DIAgRAM (18) (24) (25) Page 15... -
Page 16: Limited 90-Day Warranty
If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 16 For technical questions, please call 1-800-444-3353. LIMITED 90 DAY WARRAnTY REV 10e SKU 92880...