Advertisement
Drill bit sharpener
set up anD Operating instructiOns
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
saVe this Manual.
Copyright
2003 by Harbor Freight Tools
©
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
cover revised 09j
Model
90287
. All rights reserved. No portion of this manual or any artwork
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Chicago Electric 90287
Summary of Contents for Chicago Electric 90287
-
Page 1: Set Up And Operating Instructions
Drill bit sharpener Model 90287 set up anD Operating instructiOns Visit our website at: http://www.harborfreight.com read this material before using this product. Failure to do so can result in serious injury. saVe this Manual. Copyright 2003 by Harbor Freight Tools . -
Page 2: Important Safety Information
Unmodified plugs and matching outlets injury. will reduce risk of electric shock. avoid body contact with grounded surfaces such as pipes, radiators, Page 2 For technical questions, please call 1-800-444-3353. SKU 90287... - Page 3 Such SKU 90287 For technical questions, please call 1-800-444-3353. Page 3...
- Page 4 Sharpening head may become hot while using. This is a normal result of operation. Maintain labels and nameplates on the tool. These carry important safety Page 4 For technical questions, please call 1-800-444-3353. SKU 90287...
-
Page 5: Extension Cords
National Electrical Code. (see Outlets electrician before using it. for 2-prong plug.) Double insulated tools may be used in either of the 120 volt outlets shown in the SKU 90287 For technical questions, please call 1-800-444-3353. Page 5... -
Page 6: Specifications
150% of the rated amperes. symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions per Minute n 0 xxxx/min. (RPM) Page 6 For technical questions, please call 1-800-444-3353. SKU 90287... -
Page 7: Operation
See Figure 3. Turn the unit on while exerting a slight downward pressure onto the bit. Turn unit off after about 5-10 seconds. Examine bit according to the “Sharpening Troubleshooting” section, below. SKU 90287 For technical questions, please call 1-800-444-3353. Page 7... - Page 8 Lower the wheel by turning the KNOB to the left. This is desirable when you wish a finer ground edge, though it will take longer and require more repetitions. Page 8 For technical questions, please call 1-800-444-3353. SKU 90287...
-
Page 9: Maintenance
Parts Diagram if necessary. Unscrew the ADJUSTMENT CYLINDER (4) from the WHEEL BASE (7) by turning clockwise. Pry out the WASHER (5). Pop out the WHEEL BASE (7). SKU 90287 For technical questions, please call 1-800-444-3353. Page 9... -
Page 10: Parts List
Transmission Shaft Dust Cover Bearing Drill Index Holder Motor Housing, Upper Motor Voltage Regulator Switch Motor Housing, Lower Cord Round Screw Cord Clamp Screw Bolt Screw Washer Spindle Adaptor reV 09j Page 10 For technical questions, please call 1-800-444-3353. SKU 90287... -
Page 11: Assembly Diagram
DiagraM reV 09j SKU 90287 For technical questions, please call 1-800-444-3353. Page 11... -
Page 12: Limited 90-Day Warranty
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 reV 09j Page 12 For technical questions, please call 1-800-444-3353. SKU 90287...
Need help?
Do you have a question about the 90287 and is the answer not in the manual?
Questions and answers