Do you have a question about the 92772 and is the answer not in the manual?
Questions and answers
Lloyd Jones
May 31, 2025
Which blade type fit the Chicago 92772 ?
1 comments:
Mr. Anderson
May 31, 2025
The Chicago Electric 92772 jigsaw fits 4” x 10 TPI and 3-1/4” x 25 TPI saw blades.
This answer is automatically generated
kevan johnson
April 12, 2025
i can't new blade in please help
1 comments:
Mr. Anderson
April 12, 2025
To install a new blade on the Chicago Electric 92772 jigsaw:
1. Unplug the jigsaw. 2. Slide down the plastic blade guard. 3. Use the provided Allen wrench to loosen the two bolts holding the blade. 4. Remove the old blade. 5. Insert the new blade into the blade holder. 6. Tighten the two bolts with the Allen wrench to secure the blade. 7. Slide the plastic blade guard back into place.
Note: Blade changes are described as tedious, and the blade holder may not hold blades securely.
Electric drill bit
and chisel sharpener (15 pages)
Summary of Contents for Chicago Electric 92772
Page 1
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
Never modify the plug in any way. Do not use any adapter plugs with grounded power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b. Avoid body contact with grounded surfaces such as pipes, radiators, SKU 92772...
Page 3
Prevent unintentional starting. Ensure the switch is in the off‑ position before connecting to power source and/or battery pack, picking SKU 92772 For technical questions, please call 1‑800‑444‑3353. up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Avoid unintentional starting. Prepare to begin work before turning on the tool.
It must be understood by the operator that common sense and caution are factors which cannot be built into this SKU 92772 For technical questions, please call 1‑800‑444‑3353. product, but must be supplied by the operator.
(See Table A.) If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. SKU 92772...
Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions per Minute n 0 xxxx/min. (RPM) Strokes Per Minute SKU 92772 For technical questions, please call 1‑800‑444‑3353. Electrical Input Laser Power Speed Rating Stroke Length Blade Type Saw Blades...
Control Dial is a 6-position speed dial switch located on the top/front of the handle. By rotating the Speed Control Dial from 1 to 6, the Saw Blade speed can be set from 500 to 3,000 strokes per Page 8 For technical questions, please call 1‑800‑444‑3353.
Blade Guide Assembly (38). b. Slightly loosen the two Hex Screws (16) on the Blade Guide Assembly (38). c. Insert the Saw Blade (59, 60) upward into the Blade Guide Assembly (38), and retighten the two Hex Screws (16) to secure the Saw Blade in place.
(41) for the desired bevel of cut. Then, plug the Power Cord (43) into the nearest 120 volt, grounded, electrical outlet. Position the Saw Blade (59, 60) of the Jigsaw about 1/2” from the beginning cut SKU 92772 For technical questions, please call 1‑800‑444‑3353.
AFTER USE, wipe external surfaces of the tool with clean cloth. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. SKU 92772...
5. Motor being strained by long or small diameter extension cord. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. SKU 92772 For technical questions, please call 1‑800‑444‑3353. Troubleshooting 1. Check that cord is plugged in.
ASSEMBLY DIAGRAM 59: 4” x 10 TPI Saw Blades not shown. 60: 3‑1/4” x 25 TPI Saw Blade not shown. 61: Trigger Lock not shown. Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead.
LIMITED 1 YEAR / 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship.
Need help?
Do you have a question about the 92772 and is the answer not in the manual?
Questions and answers
Which blade type fit the Chicago 92772 ?
The Chicago Electric 92772 jigsaw fits 4” x 10 TPI and 3-1/4” x 25 TPI saw blades.
This answer is automatically generated
i can't new blade in please help
To install a new blade on the Chicago Electric 92772 jigsaw:
1. Unplug the jigsaw.
2. Slide down the plastic blade guard.
3. Use the provided Allen wrench to loosen the two bolts holding the blade.
4. Remove the old blade.
5. Insert the new blade into the blade holder.
6. Tighten the two bolts with the Allen wrench to secure the blade.
7. Slide the plastic blade guard back into place.
Note: Blade changes are described as tedious, and the blade holder may not hold blades securely.
This answer is automatically generated