Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 2...
Do not use a power tool while tired or under the influ- ence of drugs, alcohol, or medication. A moment of inattention while operat- ing power tools may result in serious personal injury. SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 3...
Page 4
Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 4...
Jigsaw by pulling on the Power Cord. Keep the Power Cord away from heated surfaces. To avoid electrical shock, do not handle the Power Cord Plug or the Jigsaw with wet hands. SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 5...
Page 6
C. When restarting the Saw in the workpiece, center the Saw Blade in the kerf and check that the saw teeth are not engaged into the workpiece. If the Saw Blade is binding, it may walk up or kickback from the workpiece SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 6...
Page 7
Laser beam back at the operator, causing poten- tial eye damage. Do not attempt to alter the Laser (55) or replace it with a different type. Doing so SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 7...
Page 8
The operator must understand that common sense and caution are factors, which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 8...
As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 9...
Page 10
FEET FEET FEET FEET FEET 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0 16.1-20.0 *Based on limiting the line voltage drop to five volts at 150% of the rated amperes. FIGURE B SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 10...
The Cutting Mode Selector has 4 position settings. The setting marked “0” is for straight cutting and the settings marked “I”, “II”, and “III” are for orbital cutting. (See Figure D.) SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 11...
Page 12
To Install A Saw Blade: WARNING! Prior to performing any assembly and/or adjustment proce- dures, make sure the Power Cord (43) of the Jigsaw is unplugged from its electrical outlet. SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 12...
Page 13
To do so, loosen the Hex Screw (16). Rotate the Base Plate right or left to the desired angle of cut. Then, retighten the Hex Screw (16). (See Figure G, next page.) SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 13...
Page 14
(46). Also if necessary, adjust the Base Plate (41) for the desired bevel of cut. Then, plug the Power Cord (43) into the nearest 120 volt, grounded, electrical outlet. (See Figures D and G.) SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 14...
Daily: With a clean cloth, remove all dirt, grease, and oil from the Jigsaw. Do not immerse the Jigsaw in any liquids. CAUTION! All maintenance, service, or repairs not listed in this manual are only to be attempted by a qualified service technician. SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 15...
60: 3-1/4” x 25 TPI Saw Blade not shown. 61: Trigger Lock not shown. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 92772 For technical questions, please call 1-800-444-3353 PAGE 17...
Need help?
Do you have a question about the 92772 and is the answer not in the manual?
Questions and answers