Table of Contents
Advertisement
5. Installation
5.1 General Safety Instructions
• Read all of these instructions. Save them for future reference.
• Follow all warnings and instructions marked on the device.
• Do not place the device on any unstable surface (cart, stand, table,
etc.). If the device falls, serious damage will result.
• Do not use the device near water.
• Do not place the device near, or over, radiators or heat registers.
• The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect
against overheating, these openings must never be blocked or covered.
• The device should never be placed on a soft surface (bed, sofa, rug,
etc.) as this will block its ventilation openings. Likewise, the device
should not be placed in a built in enclosure unless adequate ventilation
has been provided.
• Never spill liquid of any kind on the device.
• Unplug the device from the wall outlet before cleaning. Do not use
liquid or aerosol cleaners. Use a damp cloth for cleaning.
• The device should be operated from the type of power source indicated
on the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
• This device is designed for IT power distribution systems with up to
230V phase to phase voltage.
• The device is equipped with a 3-wire grounding type plug. This is a
safety feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do not attempt
to defeat the purpose of the grounding-type plug. Always follow your
local/national wiring codes.
• Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped
over.
• If an extension cord is used with this device make sure that the total of
the ampere ratings of all products used on this cord does not exceed
the extension cord ampere rating. Make sure that the total of all
products plugged into the wall outlet does not exceed 15 amperes.
• Consideration should be given to the connection of equipment to the
supply circuit, and what effect overloading the supply circuit might have
on overcurrent protection and supply wiring.
• To help protect your system from sudden, transient increases and
decreases in electrical power, use a Tripp Lite Surge Protector, Line
Conditioner, or Uninterruptible Power Supply (UPS).
• Position system cables and power cables carefully; be sure that nothing
rests on any cables.
• When connecting or disconnecting power to hot pluggable power
supplies, observe the following guidelines:
• Install the power supply before connecting the power cable to the
power supply.
• Unplug the power cable before removing the power supply.
• If the system has multiple sources of power, disconnect power from
the system by unplugging all power cables from the power supplies.
• Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of
fire or electrical shock.
• Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
• If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair:
• The power cord or plug has become damaged or frayed.
• Liquid has been spilled into the device.
• The device has been exposed to rain or water.
• The device has been dropped, or the cabinet has been damaged.
• The device exhibits a distinct change in performance, indicating a
need for service.
• The device does not operate normally when the operating
instructions are followed.
• Only adjust those controls that are covered in the operating
instructions. Improper adjustment of other controls may result in
damage that will require extensive work by a qualified technician to
repair.
• Use of this equipment in life support applications where failure of this
equipment can reasonably be expected to cause the failure of the life
support equipment or to significantly affect its safety or effectiveness
is not recommended. Do not use this equipment in the presence of a
flammable anesthetic mixture with air, oxygen or nitrous oxide.
Rack Mounting Safety Instructions
• The ambient operating temperature in the rack may be an issue and
is dependent upon the rack load and ventilation. When installing in a
closed or multi-unit rack assembly, make sure that the temperature will
not exceed the maximum rated ambient temperature.
• Before working on the rack, make sure that the stabilizers are secured
to the rack, extended to the floor, and that the full weight of the rack
rests on the floor. Install front and side stabilizers on a single rack or
front stabilizers for joined multiple racks before working on the rack.
• Always load the rack from the bottom up, and load the heaviest item in
the rack first.
• Always load the rack so that a hazardous condition is not created due
to uneven loading.
• Make sure that the rack is level and stable before extending a device
from the rack.
• Use caution when pressing the device rail release latches and sliding a
device into or out of a rack; the slide rails can pinch your fingers.
• After a device is inserted into the rack, carefully extend the rail into a
locking position, and then slide the device into the rack.
• Do not overload the AC supply branch circuit that provides power to the
rack. The total rack load should not exceed 80 percent of the branch
circuit rating.
• Ensure that proper airflow is provided to devices in the rack.
• Do not step on or stand on any device when servicing other devices in
a rack.
• Do not connect the RJ11 connector marked "Upgrade" to a public
telecommunication network.
• Caution! Slide/Rail (LCD KVM) mounted equipment is not to be used
as a shelf or a work space.
equipment is not to be
7
CAUTION!
Slide/rail-mounted
used as a shelf
or a workspace.
Advertisement
Table of Contents
