Electrolux EFEP956 Installation & User Manual page 27

52 electrolux.com.au
USING THE INDUCTION HOB
Power management
Power management divides the power between the
front and rear zones for each of the 2 outer modules.
See illustration below:
This allows either the front or rear zone to draw power
from the other, if maximum power is required.
The timer
The count down timer
Use the count down timer to set how long you want a
cooking zone to operate.
IMPORTANT!
• To select the cooking zone: touch the sensor
and again until the correct zone indicator is displayed.
• Immediately, touch the sensor to set the time (00 -
99 minutes). When the timer indicator of the cooking
zone starts to flash more slowly the time will begin to
count down.
• To see the remaining time select the cooking
zone with the sensor. The display will show the
remaining time.
• To change the count down timer: select the cooking
zone with the sensor and touch or
• To deactivate the count down timer select the cooking
zone with the sensor and touch until the time
counts down to 00. The timer indicator will go out.
When the timer count down comes to an end, the cooking
zone will deactivate, the 00 will flash and a beep sound
will occur for 20 seconds.
The beep sound and flashing can be deactivated
immediately by touching the sensor. IMPORTANT!
When the two timer functions operate at the same time,
the display shows the count up timer first.
(CONTINUED)
The Minute minder
You can use the timer as a minute minder when the
cooking zones are not in operation. Touch
touch or of the timer to set the time. When the timer
countdown comes to an end, 00 will flash and a beep
sound will occur for 30 seconds. The beep sound and
flashing can be deactivated immediately by touching the
sensor.
The Stop+Go function
Use the function to close down all of your operating
cooking zones to the lowest heat setting with just one
touch.
• To activate this function touch . The indicator
will come on and the symbol will show on all
operating zones.
• When is activated, you cannot change the heat
setting.
• To deactivate this function touch
setting that you set before comes back on.
again
.
Deactivating the beep sound
The beeping sound can be deactivated if required.
. Then
• First deactivate the hob.
• Then hold down
come on and then go out. Then hold down
seconds. 60 will now be displayed.
• Touch
now be off.
• When the sound is deactivated you will still hear
sounds when:
5 You touch
6 You put something on the control panel.
7 The timer alert comes on.
To reactivate the sound
• First deactivate the hob.
again. The heat
• Then hold down
come on and then go out. Then hold down
seconds. 61 will now be displayed.
• Touch
now be on.
Lock
Use this function to prevent an accidental change of the
heat settings.
• First set the heat setting.
• To start this function touch
show on all zones for 4 seconds before reverting back
to the heat settings.
• The indicator above the lock sensor will remain on.
• Timer functions will continue to operate after the lock
is activated.
• To stop this function touch
appliance will also stop this function.
Child safety lock
Use this function to prevent an accidental operation
of the hob.
•
for 3 seconds. The displays will
for 3
•
and change display to 61. The sound will
•
.
•
for 3 seconds. The displays will
for 3
and change display to 60. The sound will
. The symbol will then
again. Deactivating the
53
To activate this function, first turn the hob on by
touching the sensor.
Then hold down the sensor for 2 seconds. will
then show on all zones for 4 seconds before reverting
back to the heat setting.
Turn the hob off by touching the sensor again and
the hob is now in a mode where the heat settings
cannot be accidentally operated.
To unlock, first turn the hob back on by touching the
sensor, and then hold down the sensor again.
Touch again to switch off. This will bring the hob
back to normal operating mode.