Table of Contents
Advertisement
Quick Links
JWL-1442VSK, 14" X 42" VS
PRO WOOD LATHE WITH
LEGS
708358K
This mid range lathe offers mechanical variable speed along with a
headstock that pivot as well as slide to the end of the bed for
outboard turning capabilities
FEATURES
Reeves drive pulley system allows quick variable speed
changes from 450 to 3,000 RPM
Heavy-duty cast-iron lathe bed adds stability while limiting
vibration during operation
Headstock swivels 360° with positive stops at 45° and 90°
and may be positioned anywhere along the bed ways for
maximum flexibility and user comfort
Spindle has positive locking indexing in 10 degree
increments for fast, efficient fluting and veining operations
Built-in spindle locks let you remove or replace faceplates
and chucks with ease
Live center has a removable pin for boring through stock
Cam-lock mechanisms allow adjustments of headstock,
tailstock and tool rest base without having to use tools
Hollow tailstock allows you to perform long hole boring for
lamps and other vessels
Special cast-in webbings in legs accept 2 x 4's or a 2 x 12
to construct a solid tool or sandbag shelf
RESOURCES
Manual
View More Details
SPECIFICATIONS
Size (In.)
Style (Type)
Swing Over Bed (In.)
Swing Over Tool Rest Base (In.)
Distance Between Centers (In.)
Headstock Movement
Spindle Bore (In.)
Tailstock Bore
Spindle Taper
Quill Taper
Quill Travel (In.)
Spindle Thread (In./TPI)
Outboard External Threads (In. x TPI)
Spindle Speeds
Speed Range
Number of Indexing Positions
Centerline of Spindle to Floor (In.)
Woodworking
14
10
42
Pivot 360, Slide
450-3000
36
43-1/2
Advertisement
Table of Contents
Related Manuals for Jet JWL-1442VSK
Summary of Contents for Jet JWL-1442VSK
- Page 1 JWL-1442VSK, 14" X 42" VS PRO WOOD LATHE WITH LEGS 708358K This mid range lathe offers mechanical variable speed along with a headstock that pivot as well as slide to the end of the bed for outboard turning capabilities FEATURES...
- Page 2 This .pdf document is bookmarked Operating Instructions and Parts Manual JWL-1442VS Wood Lathe WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708358 Ph.: 800-274-6848 Revision D1 11/2010 www.waltermeier.com Copyright © 2010 Walter Meier (Manufacturing) Inc...
-
Page 3: Warranty And Service
Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with your local Walter Meier distributor, or visit waltermeier.com. WARRANTY JET products carry a limited warranty which varies in duration based upon the product (MW = Metalworking, WW = Woodworking). WHAT IS COVERED? This warranty covers any defects in workmanship or materials subject to the exceptions stated below. -
Page 4: Table Of Contents
Table of Contents Warranty and Service..........................2 Table of Contents ..........................3 Warnings............................4 Introduction ............................6 Specifications .............................6 Shipping Contents ..........................7 Contents of the Shipping Containers ....................7 Unpacking and Clean-Up .........................7 Assembly ............................7 Stand Legs .............................7 Tool Rest ............................8 Stand Shelf .............................8 Grounding Instructions ........................9 Controls and Features........................ -
Page 5: Warnings
Warnings 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. This wood lathe is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a wood lathe, do not use it until the proper training and knowledge have been obtained. - Page 6 33. Do not use this JET wood lathe for other than its intended purpose. If used for other purposes, Walter Meier (Manufacturing) Inc., disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.
-
Page 7: Introduction
Walter Meier. Walter Meier can also be reached at our web site: www.waltermeier.com. Specifications Model Number ........................ JWL-1442VSK Stock Number ........................708358K Motor ............TEFC 1HP, 1PH, 115V/230V, Prewired 115V. 60Hz, 11/5.5A Switch ....................manual, paddle style with lockout Construction: Headstock .......................... -
Page 8: Shipping Contents
Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury. Shipping Contents Contents of the Shipping Containers Lathe with Leg Set Tailstock Headstock Face Plate Tool Rest Body Accessory Package 708358K Owner’s Manual and Warranty Card Accessory Package Box... -
Page 9: Tool Rest
2. Thread adjustable feet (A, Fig. 1) into stand leg (B, Fig. 1). There is a flat spot on the shaft near the foot that will accommodate a wrench. Thread a hex nut (C, Fig. 1) onto shaft and leave loose for now. 3. -
Page 10: Grounding Instructions
must be connected to a permanent ground such Grounding Instructions as a properly grounded outlet box, as shown in Figure B. This tool must be grounded extension cord while in use to protect the operator from recommended. However, if you must use one electric shock. -
Page 11: Controls And Features
Controls and Features E. Headstock Lock Handle: (E, Fig. 4) Locks the head in position. Unlock the handle to position the head in any location along the lathe bed. Tighten handle when properly positioned. F. Headstock Indexing Pin: (F, Fig. 4 Turn the knurled knob counter-clockwise to unlock the plunger. - Page 12 K. Headstock Faceplate: (K, Fig. 7) Used for turning bowls. There are a number of screw holes for mounting the workpiece. Thread the faceplate onto the spindle in a clockwise direction. Remove the faceplate by pushing in headstock spindle lock and using the provided wrench on faceplate flats.
-
Page 13: Lathe Tools
Lathe Tools 1. With a ruler locate and mark the center on each end by going corner to corner, see Figure 12. If possible, select only high quality, high speed Accuracy is not critical on full rounds but steel turning tools with long handles. As one extremely important on stock where square becomes proficient in turning, a variety of specialty sections are to remain. -
Page 14: Operations
Operations Stock Selection Stock for spindles should be straight grained and free of checks, cracks, knots and other defects. It should be cut 1/8" to 1/4" larger than the finished diameter and may require additional length to remove ends if required. Larger stock should have the corners removed to produce an octagon making the piece easier to rough down to a cylinder, see Figure 13. -
Page 15: Beads
Beads Parting 1. Place the parting tool on the tool rest and move Place parting tool on tool rest and raise the handle the tool forward to make the full bevel of the until it starts to cut and continue to cut to the tool contact the workpiece. -
Page 16: Sanding And Finishing
Sanding and Finishing Leaving clean cuts will reduce the amount of sanding required. Begin with a fine sandpaper (120 grit or finer). Coarser sandpaper will leave deep scratches that are difficult to remove, and dull crisp details. Fold the sandpaper into a pad; do not wrap sandpaper around your fingers or the workpiece. -
Page 17: Face Plate Or Chuck
Face Plate or Chuck Tools for Bowl Turning While faceplates are the simplest, most reliable The deep fluted bowl gouge is the most essential method of holding a block of wood for turning, and versatile tool for most bowl and faceplate style chucks can also be used. -
Page 18: To Shape The Outside Of A Bowl
1/4" from the workpiece. Note: For larger outboard turning, an optional outboard turning stand is used to place the tool support, see your JET distributor. 5. Turn the workpiece by hand to ensure proper clearance. 6. Start the lathe at the lowest speed and bring it up to the maximum safe speed for the size of work to be turned, see Figure 6 on page 11. -
Page 19: To Shape The Interior Of A Bowl
To Shape the Interior of a Bowl Sanding and Finishing a Bowl 1. Stop the lathe and move the tailstock away. 1. Remove the tool rest and begin with a fine grit Remove the center from the tailstock to prevent sandpaper (120 grit) and progress through bumping it with your elbow. -
Page 20: Adjustments
Changing the Belt and Bearings Changing belt and bearings can be a difficult task, and should be performed by a JET authorized Figure 23 repair station. Remove headstock and take into a repair station for servicing. -
Page 21: Optional Accessories
Optional Accessories Safety Guard The JWL-1442VS Safety Guard is an optional accessory. Referring to Figure 26: 1. Mount the guard bracket (A) to the headstock with two 3/8” flat washers, two 3/8” lock washers and two 3/8”-16 x 1-1/2” socket head cap screws (B). -
Page 22: Troubleshooting
Troubleshooting Problem Possible Cause Solution 1. Workpiece warped, out of round, has 1. Correct problem by planing, major flaw, improperly prepared for bandsawing, reduce the RPM, Excessive Vibration. turning, or RPM is set too high or scrap workpiece all together 2. -
Page 23: Bed Assembly Parts List
16 .... JWL1442-216 ..Live Center..................1 17 .... JWL1442-217 ..Tailstock Rod ..................1 18 .... JWL1442-218 ..Tailstock Quill Handle ................. 1 19 .... JWL1442-219 ..JET Label................... 1 20 .... TS-0267021 ....Set Screw ............1/4”-20 x 1/4” ....2 21 .... JWL1442-127 ..Bushing....................1 22 .... -
Page 24: Headstock Assembly - Parts List
Headstock Assembly – Parts List Index No. Part No. Description Size 1 ....JWL1442-101 ..Spur Center............MT2 ......1 2 ....JWL1442-102 ..Face Plate............6”....... 1 3 ....JWL1442-103 ..Spindle ....................1 4 ....JWL1442-104 ..Key ..............4 x 4 x 80 ....1 5 .... - Page 25 52 .... TS-0720081 ....Lock Washer ............5/16” ......2 53 .... JWL1442-153 ..Plate ....................1 54 .... JWL1442-154 ..Clamp ....................1 55 .... JWL1442-155 ..JET Label................... 1 56 .... JWL1442-156 ..Warning Label ..................1 57 .... JWL1442-157 ..Speed Label ..................1 58 ....
-
Page 26: Headstock Assembly
Headstock Assembly... -
Page 27: Stand Assembly
Description Size 3 ....JWL1642-203 ..Stand ....................2 5 ....JWL1642-205 ..JET Stripe ..................1 6 ....JWL1642-206 ..Adjustable Foot ..........3/8” ......4 7 ....TS-0561031 ....Hex Nut............3/8” ......4 9 ....TS-0208081 ....Hex Socket Cap Screw ........5/16”-18 x 1-1/2” ..8... -
Page 28: Safety Guard Assembly
Safety Guard Assembly Index No. Part No. Description Size 1 ....JWL1442-301 ..Guard Bracket ..................1 2 ....TS-0270011 ....Set Screw ............5/16”-18x1/4” ....2 3 ....JWL1642-187 ..Collar ....................2 4 ....TS-0680041 ....Flat Washer............3/8” ......2 5 ....TS-0720091 ....Lock Washer ............3/8” ......2 6 .... -
Page 29: Wiring Diagram
Wiring Diagram... -
Page 30: Appendix - Indexer Positions
Appendix – Indexer Positions How to use the chart A diagram of the indexer is shown at right, as viewed from the tailstock end of the Lathe. Points A, B and C are the holes in the head casting. The holes in the spindle collar may be considered as numbered 1 through 12. - Page 31 Notes...
- Page 32 Notes...
- Page 33 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jetttools.com www.waltermeier.com...