Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Charnwood BS410
Summary of Contents for Charnwood BS410
- Page 1 10” BANDSAW OWNERS MANUAL MODEL: BS410 Charnwood Machinery Ltd, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have thoroughly read and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner's manual and review frequently for continuous safe operation. - Page 3 Risk of Injury! Wear Eye Wear Ear Never reach into Protection Protection Moving parts BS410 Specification Table size 340 x 335 mm Table Size with Extension 490 x 335 mm Motor 240v / 50Hz 370W (1/2hp) Blade length 1712 mm (67-1/2”) Blade speed (no load) 730±10% m/min...
- Page 4 Unpacking The Bandsaw Cut the strapping and remove the polystyrene insert from the carton. Remove all parts from the packaging, look underneath the packaging too. Layout the parts as shown to check they are all present. Please Note: As a safety feature, this model is fitted with micro switches on both upper and lower doors.
-
Page 5: Assembling The Bandsaw
Assembling The Bandsaw Pull the table extension out so you can slot the table into place on the trunnion. Line up the four threaded holes in line with the holes in the upper trunnion. Use the four bolts attach the table to the trunnion, leaving the bolts slightly loose. - Page 6 Check the blade is centred in the table insert slot without interference. If the blade is offset to one side or the other, it can now be adjusted. The lower trunnion is attached to the body of the saw by four hex headed bolts.
- Page 7 Having set the table so that the blade is centred, apply a little tension to the blade and use a set square to position the table at right angles to it. Lock it in position and if necessary, set the adjustable pointer so it aligns with zero.
- Page 8 Setting Up The Bandsaw Blade tensioner adjuster Blade tensioner quick release lever Blade guard adjuster and lock Blade Tracking control adjuster and lock Set the Blade Tension Make sure the blade tension quick release lever is in the down position. The blade tension indicator is to be used as a guide.
- Page 9 Set the Blade Tracking Unlock the adjuster using the wingnut. By hand, slowly rotate the bandsaw upper wheel clockwise. If the blade starts to move forward or backwards on the wheel adjust the tracking control until the blade is balanced. The blade can sit in the centre of the rubber tyre or with the tips of the teeth projecting over the front end.
- Page 10 Set The Rip Fence Scale Fit the rip fence to the table. Use a ruler to measure the distance between the blade and the fence. Slide the scale left or right to adjust the scale to match the measurement you have taken.
-
Page 11: Making A Cut
Your bandsaw is now ready for use. It is recommended that the saw is bolted to a bench and a suitable dust extractor attached. Making A Cut For every type of cut, the blade guard should be lowered so that the bottom edge of the guard is just above the work piece. -
Page 12: Replacing The Blade
Replacing The Blade When you notice the cutting performance of the bandsaw starts to deteriorate it is time to replace the blade. Bandsaw blades are sharp enough to cause injury even when too blunt to cut wood! It is recommended that protective gloves be worn when handling blades. -
Page 13: Troubleshooting
Declaration of Conformity for CE Marking Charnwood Declare that Woodworking Bandsaw, Model BS410 Conforms with the following Directives: Machinery Directive 2006/42/EC EMC Directive 2014/30/EU And further conforms to the machinery example for which the EC type examination Certificate No. BM 50331328 and AE 50349294 have been issued by TUV Rheinland LGA Products GmbH, Tillystrasse 2, 90431, Nurnberg, Germany. - Page 14 BS410 Parts Diagram Optional Floor Stand...
- Page 15 BS410 10” Bandsaw Parts List...
- Page 16 Updated September 2019 Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...