Related Manuals for Charnwood W721
Summary of Contents for Charnwood W721
- Page 1 W721 BANDSAW Address; Charnwood, Cedar Court, Walker Road, Bardon Hill, Leicestershire, LE67 1TU Telephone; 01530 516 926 Fax; 01530 516 929 email; sales@charnwood.net...
- Page 2 1. Components and Parts (standard delivery ) REAR Front 14. Quick release lever for band saw blade 1. Upper housing door 15.Setting knob for blade tracking adjustment 2. Setting knob for band saw blade tension 16.Setting knob for table turning adjustment 3.
-
Page 3: Table Of Contents
Table of contents be used as follows: Additional information. Components and parts • Read these instructions before use. (standard delivery)………..….1 3. Safety Pay special attention to the safety Please read first! ..…....….2 information. 3.1 Specified conditions of use Safety ........……2 •... -
Page 4: Symbols On The Machine
cutting tool at standstill! Do not operate tool near inflammable beech, ash) can cause cancer when liquids or gases. Wear gloves when changing cutting tools. inhaled: work only with a suitable dust The saw shall only be started and collector connected to the saw. Risk of kickback (work piece is operated by persons familiar with band caught by the band saw blade... -
Page 5: Safety Devices
the hand and protects against accidental 3.4 Safety devices contact with the saw blade. The push stick must always be used if the distance between band saw blade and a rip fence is less than 120 mm. Guide the push stick at an angle of 20° …... -
Page 6: Initial Operation
fence the lock handle must be firmly turning setting knob tightened. clockwise reduces the blade tension 6. Initial Operation turning setting knob Danger! counterclockwise increases the Start the saw only after the blade tension. following preparations completed: the saw is securely mounted ; the saw table is installed and aligned;... -
Page 7: Installing The Saw Table
6.6 Installing the Push Stick 6.2 Installing the Saw Table Holder Check band saw blade tension (see Fit limit stop screw (40) to the Note: "Initial operation"). underside of the low house . Loosen lock lever. If the saw is to be mounted on Guide saw table over the band saw Using a try square, set the table at the stand, the push stick holder can... -
Page 8: Tensioning The Band Saw Blade
6.8 Tensioning the Band Saw a dry environment. 1.5 mm Blade Operate the saw only on a power Do not pull on the power supply Danger! source matching following cable to unplug. Too much tension can requirements (see also "Technical When the saw is assembled and all cause the band saw blade to break. - Page 9 washer then secure on upper side be set approx. 3 mm above the work with hex nut. Repeat procedure for all piece); four corners before tightening fully. after adjustments of band saw blade 7. Operation or saw table (e.g. band saw blade Danger! change, tensioning of the band saw To reduce the risk of personal...
-
Page 10: Sawing
• Close the lower housing door. Repair and maintenance work other guide it through 7.1 Sawing than described in this section should the slot in the saw table, 1. Choose and install a table insert only be carried out by qualified the blade guard on the upper blade extrusion suitable for the type of cut to be specialists. -
Page 11: Aligning The Upper Blade Guide
(distance thrust bearing - band saw Loosen lock nut (56). blade = 0.5 mm – if the band saw Turn setting knob (57): blade is turned by hand, it must not Turn setting knob (57) clockwise if touch the thrust bearing). the band saw blade runs towards the Tighten the thrust bearing lock front of the saw. -
Page 12: Repairs
outdoors, in unprotected areas or in start again. Band saw blade length 2240mm damp or wet locations. Band saw blade wanders off the line of Max. throat capacity 305mm cut or runs off the band saw wheels Max. band saw blade width 20 mm 9. -
Page 13: Electric Wiring Diagram
13. Electrical wiring diagram - 12 -... - Page 14 14. Exploded view drawing and part list - 13 -...
- Page 15 ITEM PART NO. NAME Q'ty 31504100A Lower door GB70-85 M6×16 Hex. socket set columned head bolt DJ31703012 Spacer bushing GB889-86 M6 Hex. Locking nut DJ315S03012-01 Pilot guide 31503035 spring plate GB12618-90 4×10 Rivet 31504003 Pilot pin 31503100A upper door GB894.1-86 15 Circlip for shaft 31503005A Bearing bolt upper...
- Page 16 31504013 Sliding shaft CK-5 Switch DJ31703008 DJ31703009 Screwed flange 31505002 Lamello plug 31503006 Setting knob GB6172-86 M8 Hex. Thin nut DJ38003004-01 Thread bolt DJ38003002 Bracket for saw blade tension GB6173-86 M20×1.5 Hex. Nut DJ31703010 Seat for quick release shaft DJ38003007 Quick release shaft GB6172-86 M10 Hex.
- Page 17 DJ315S02001-18 DJ315S02001-09 Fence bracket GB/T801-98 M6×45 Cup head square neck bolt DJ315S02001-10 Fence DJ315S02001-05 Pressure plate DJ350A02007 Fence carrier RTS250G04012 Pastic pressure plate GB845-85 ST3.5×9.5 Cross recessed pan head tapping screw RTS250G04011 TJ250D04013 Handle TJ315B04015 DJ315S02001-08 Shaft RTS250G06010 Pointer GB70-85 M6X12 Hex.