Makita TD111DSAJ Instruction Manual
Hide thumbs Also See for TD111DSAJ:


Quick Links

Cordless Impact Driver
Read before use.


Table of Contents

Summary of Contents for Makita TD111DSAJ

  • Page 1 INSTRUCTION MANUAL Cordless Impact Driver TD111D Read before use.
  • Page 2: Specifications

    SPECIFICATIONS Model: TD111D Fastening capacities Machine screw 4 mm - 8 mm Standard bolt 5 mm - 14 mm High tensile bolt 5 mm - 12 mm No load speed Hard impact mode 0 - 3,000 min Soft impact mode 0 - 1,300 min Impacts per minute Hard impact mode...
  • Page 3: General Power Tool Safety Warnings

    Prevent unintentional starting. Ensure the SAFETY WARNINGS switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with General power tool safety warnings your finger on the switch or energising power tools that have the switch on invites accidents. WARNING: Remove any adjusting key or wrench before Read all safety warnings and all...
  • Page 4 WARNING: DO NOT let comfort or familiarity causing fires, personal injury and damage. It will with product (gained from repeated use) replace also void the Makita warranty for the Makita tool and strict adherence to safety rules for the subject charger. product. MISUSE or failure to follow the safety rules stated...
  • Page 5: Functional Description

    Overloaded: FUNCTIONAL The tool is operated in a manner that causes it to draw an abnormally high current. DESCRIPTION In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart. CAUTION: Always be sure that the tool is If the tool does not start, the battery is overheated. In switched off and the battery cartridge is removed this situation, let the battery cool before turning the tool before adjusting or checking function on the tool.
  • Page 6 Switch action ► 1 . Button Pull the switch trigger to turn on the lamp. To turn off, ► 1 . Switch trigger release it. The lamp goes out approximately 10 seconds after releasing the switch trigger. CAUTION: Before installing the battery car- To keep the lamp off, turn off the lamp status. To turn off tridge into the tool, always check to see that the the lamp status, first pull and release the switch trigger. switch trigger actuates properly and returns to And then press the button for one second within 10 the "OFF"...
  • Page 7 This tool has a reversing switch to change the direction CAUTION: Always check the direction of of rotation. Depress the reversing switch lever from the rotation before operation. A side for clockwise rotation or from the B side for coun- terclockwise rotation. CAUTION: Use the reversing switch only after When the reversing switch lever is in the neutral posi- the tool comes to a complete stop. Changing the tion, the switch trigger cannot be pulled. direction of rotation before the tool stops may dam- age the tool.
  • Page 8: Installing Hook

    To install the driver bit, pull the sleeve in the direc- ASSEMBLY tion of the arrow and insert the bit-piece and driver bit into the sleeve as far as it will go. The bit-piece should be inserted into the sleeve with its pointed CAUTION: Always be sure that the tool is end facing in. Then release the sleeve to secure switched off and the battery cartridge is removed the driver bit. before carrying out any work on the tool.
  • Page 9: Operation

    High tensile bolt OPERATION N•m (kgf•cm) (1,224) (1,020) (816) (612) (408) The proper fastening torque may differ depending upon the kind or size of the screw/bolt, the material of the (204) workpiece to be fastened, etc. The relation between fas- tening torque and fastening time is shown in the figures. Standard bolt N•m 1. Fastening time (second) 2. Fastening torque (kgf•cm) 3. Proper fastening torque corresponding to each bolt diameter (1,224) Hold the tool firmly and place the point of the driver bit in the screw head. Apply forward pressure to the tool to (1,020) the extent that the bit will not slip off the screw and turn the tool on to start operation.
  • Page 10: Using Holster

    ► 1 . Holster holder 2. Waist belt Put the tool in the holster and lock it with the hol- CAUTION: These accessories or attachments ster button. are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center.
  • Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885522-910 20160511...

This manual is also suitable for:


Table of Contents