Residual Risks; Electrical Safety - Stanley STDH8013C Original Instructions Manual

5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional Power Tool Safety Warnings
Warning! Additional safety warnings for drills and
impact drills
Drill Safety Warnings
• Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
• Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
• Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
• Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
• Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
• Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
• This tool is not intended for use by persons(including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the appliance.
• The intended use is described in this instruction manual.
The use of any accessory or attachment or performance of
any operation with this tool other than those recommended
in this instruction manual may present a risk of personal
injury and/or damage to property.
Safety of others
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
• Children should be supervised to ensure that they do not
play with the appliance

Residual risks

Additional residual risks may arise when using the tool which
(Original instructions)
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc. Even with the
application of the relevant safety regulations and the
implementation of safety devices, certain residual risks can
not be avoided. These include:
• Injuries caused by touching any rotating/moving parts.
• Injuries caused when changing any parts, blades or
accessories.
• Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
• Impairment of hearing.
• Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Labels on tool
The label on your tool may include the following symbols:
Hz ....... Hertz
Read
Instructions
W ........ Watts
Manual
min ..... minutes
Use Eye
Protection
..... Alternating
Use Ear
Protection
..... Direct
V ........ Volts
n ....... No-Load
0
A ........ Amperes
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2017 XX JN
Year of manufacturing

Electrical safety

Double insulation measures are taken in this power
tool, so no grounding is needed. Please check
whether the voltage of power supplied is consistent
with the voltage on the nameplate or not.
• If the wire is damaged, it should be replaced by the
manufacturer or a service center authorized by STANLEY,
to avoid danger.
Using an extension cable
• If an extension cable is requred, use an approved
extension cable suitable for the power input of this tool
(see technical data). The minimum conductor size is
2
1.5 mm .
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
ENGLISH
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Current
Symbol
.../min.. Revolutions
Current
or Recipro-
cation per
minute
Speed
5