Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for dallmeier MDF5400HD-DN
Summary of Contents for dallmeier MDF5400HD-DN
- Page 1 MDF5400HD-DN Commissioning English 006834 | Rev. 1.0.1 | 2018-12-19...
- Page 2 Third-party trademarks are named for information purposes only. Dallmeier electronic respects the intellectual property of third parties and always attempts to ensure the complete identification of third-party trademarks and indication of the respective holder of rights. In case that protected rights are not indicated separately, this circumstance is no reason to assume that the respective trademark is unprotected.
-
Page 3: Table Of Contents
Transportation and Packaging Warranty Appropriate Use Operation Approvals/Certifications 6 Requirements Ambient Conditions Power Supply 7 Maintenance 8 Installation and Commissioning 9 Interfaces 10 Inserting a Memory Card 11 Pin Assignment 12 Connection and Login Connection Login 13 Technical Product Specification (Basic Data) 14 Dimensions Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... -
Page 4: Validity
The product documentation for the device contains several documents which are included in the scope of delivery in a printed form and/or on a digital medium. Additional information, if available, is provided exclusively on the website www.dallmeier.com. Read the complete product documentation for the device carefully and thoroughly before using the device. Always observe and follow the contained instructions, notes and warnings as well as the technical data in the currently valid product specification. -
Page 5: Other Applicable Documents
The target audience of the document is trained system integrators (video security/surveillance systems installation contractors). Configuration The document entitled “Configuration” contains detailed information concerning the configuration of the device. The target audience of the document is trained system integrators (video security/surveillance systems installation contractors). Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... -
Page 6: Typographical Conventions
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE NOTICE addresses practices not related to physical injury and indicates measures to prevent device and/or property damage due to improper installation, assembly, wiring, operation, configuration or maintenance of the device. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... - Page 7 (menu items, buttons, etc.). Paragraphs in italics provide information on basic principles, special features and efficient procedure as well as general recommendations. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
-
Page 8: Safety Instructions
• Modifications to the Device Do not make any modifications to the hardware or software of the device that have not been tested and approved by Dallmeier. Inappropriate modifications may cause malfunctions, damage and data loss and may result in the loss of warranty. - Page 9 The product documentation for the device contains several documents which are included in the scope of delivery in a printed form and/or on a digital medium. Additional information, if available, is provided exclusively on the website www.dallmeier.com. Read the complete product documentation for the device carefully and thoroughly before using the device. Always observe and follow the contained instructions, notes and warnings as well as the technical data in the currently valid product specification.
- Page 10 Do not dispose waste electrical and electronic equipment into the household trash. Disconnect the device from the power supply. Remove all connected peripherals. Return the device to the sales partner responsible for your area. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
-
Page 11: General Notes
Transportation and Packaging Store the original packaging for later transportation. Dallmeier is not responsible for any damage resulting from unprofessional or improper transportation. The device should only be shipped in the original packaging. If the original packaging is no longer available, ensure that the used packaging sufficiently protects the device against damage, moisture, heat and cold. -
Page 12: Appropriate Use
Commissioning Appropriate Use The MDF5400HD-DN is a high-resolution single-sensor network camera with fisheye lens for detailed capturing of a 360° panoramic field of view within a complete half-space (hemisphere – half of a sphere). The lens-sensor unit of the device is built into an ultra-compact dome housing, the connected encoder unit into a separate box housing. -
Page 13: Operation
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... -
Page 14: Requirements
NOTICE Damage to the device due to unfavorable ambient conditions Use of the device under unfavorable ambient conditions may shorten its lifetime and may cause malfunction or damage to the device. ➡ Only install/operate the device under favorable ambient conditions. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... -
Page 15: Power Supply
➡ Carry out all protective measures for a standard-compliant grounding/earthing and a correct equipotential bonding of the device in accordance with the currently applicable DIN, VDE and ISO standards in order to ensure the safety of the device (protection against over-voltages) and its immunity to electromagnetic interferences (EMI). Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... - Page 16 ➡ Always disable PoE on the relevant port of your PoE switch (or PoE midspan device) or disconnect the used single-port PoE injector from the power supply before un-mating the jack-plug connection in order to prevent damage to the contacts of the RJ45 connectors by contact erosion. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
-
Page 17: Maintenance
➡ To remove greasy dirt such as fingerprints, only use cleaning products (lens cleaning solutions, cleaning wipes, etc.) that are specially designed for cleaning optical surfaces. • Do not use organic solvents (alcohol, benzine) for cleaning the lens element. • Generally, be aware not to touch the lens element to avoid fingerprints. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... -
Page 18: Installation And Commissioning
➡ Before installing the device, follow the manufacturer’s instructions regarding the maximum permissible carrying capacity of the suspended ceiling or ceiling panel. ➡ Only use screws and, if necessary, anchors/dowels that are suitable for the construction material and thickness of the ceiling panel. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... - Page 19 Commissioning MDF5400HD-DN Suspended Ceiling – Panel Thickness t t = 9 – 18 mm t < 9 mm or t > 18 mm Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 20 When using an electrically powered jigsaw or a hand saw, you should first draw a circle line with a radius of 35 mm around the center point to ensure the specified diameter and roundness of the installation hole. If necessary, use the drilling template provided. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 21 If necessary, use the provided hand tool as shown above to loosen the screw connection more easily. NOTICE: When using the provided hand tool, be careful not to scratch the housing ring. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 22 Proceed with caution when lifting out the plastic cap with a screwdriver. Be careful not to scratch the housing (wrap a protective tape around the screwdriver if necessary) and not to damage any components. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 23 ➡ Pass the encoder unit through the ceiling panel and insert the dome housing into the installation hole. Before inserting the dome housing, make sure that both retaining wings are swiveled in (left picture – default position ex works). Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 24 To do this, tighten the Phillips PH1 screw of both retaining wings with a suitable screwdriver in clockwise direction until both retaining wings swivel out and the dome housing is firmly anchored in the ceiling panel (see next page). Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 25 MDF5400HD-DN When removing the device at a later date, the retaining wings on the dome housing must be swiveled back to their default position (by simply turn- ing the corresponding screws counterclockwise). Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 26 Commissioning A-❻ ➡ Reinsert the plastic cap back to its original position in the dome housing. When doing so, ensure that the cylindrical mount for the ambient light sensor is aligned correctly. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 27 ➡ Screw the housing ring in clockwise direction back onto the dome housing as far as it will go. Use the provided hand tool as shown above to tighten the housing ring. NOTICE: Be careful not to scratch the housing ring with the hand tool. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 28 (e.g. when replacing the ceiling panel). NOTICE: Pay attention to the suitable screw length, depending on the panel thickness, in order not to penetrate the ceiling panel on the later visible side. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 29 ➡ Connect the required cables and finally establish the power supply (via PoE or by an external power supply unit). The device starts up and is ready for operation after a few minutes. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 30 MDF5400HD-DN Commissioning B-❶ Panel thickness t < 9 mm or t > 18 mm Ø 5 mm (3×) The drilling/cutting entry point should always be on the later visible side of the ceiling panel. Ø 70 mm Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 31 If you no longer have the provided drilling template at hand, you can also find it at www.dallmeier.com on the corresponding product page for the device. However, make sure to print the downloaded drilling template in its original size (at a 1:1 scale).
- Page 32 If necessary, use the provided hand tool as shown above to loosen the screw connection more easily. NOTICE: When using the provided hand tool, be careful not to scratch the housing ring. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 33 ➡ Pass the encoder unit through the ceiling panel and insert the dome housing into the installation hole (insert suitable anchors/dowels into the existing drill holes beforehand, if applicable). Before inserting the dome housing, make sure that both retaining wings are swiveled in (left picture – default position ex works). Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 34 MDF5400HD-DN Commissioning B-❹ ➡ Fix the dome housing with three suitable screws (e.g. chipboard screws with a diameter of 3 – 4 mm) in the ceiling panel. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 35 ➡ Screw the housing ring in clockwise direction back onto the dome housing as far as it will go. Use the provided hand tool as shown above to tighten the housing ring. NOTICE: Be careful not to scratch the housing ring with the hand tool. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 36 (e.g. when replacing the ceiling panel). NOTICE: Pay attention to the suitable screw length, depending on the panel thickness, in order not to penetrate the ceiling panel on the later visible side. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 37 ➡ Connect the required cables and finally establish the power supply (via PoE or by an external power supply unit). The device starts up and is ready for operation after a few minutes. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
-
Page 38: Interfaces
MDF5400HD-DN Commissioning 9 Interfaces ⓒ ⓑ ⓓ ⓔ ⓐ ⓕ Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... - Page 39 The orientation of your device’s RJ45 jack may differ from the figure previously shown. ➡ Observe the chapter “Pin Assignment” on page 42. ➡ Connect the required cables to the relevant interfaces of the encoder unit. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
-
Page 40: Inserting A Memory Card
MDF5400HD-DN Commissioning 10 Inserting a Memory Card ⓐ ⓐ microSDXC card (optional) Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... - Page 41 The use of an incompatible memory card may damage the device or memory card or corrupt the data stored on it, resulting in malfunctions and loss of data. ➡ Only use memory cards that have been tested and approved by Dallmeier (failure to do so may result in the loss of warranty). Damage to the device or memory card due to incorrect card insertion ➡...
-
Page 42: Pin Assignment
Line OUT (stereo) Left channel Left channel Ring Right channel Right channel Sleeve Ground Ground Audio Line IN (stereo) Audio Line OUT (stereo) Input level: max. 2.83 V Output level at 10 kΩ load: max. 3.11 V Input impedance: 29 kΩ Output impedance: 320 Ω Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... - Page 43 ➡ Do not operate the device with Power over Ethernet (PoE) if the device is powered by an external DC power supply unit. In order to comply with UL’s requirements, only use a UL certified “Limited Power Source (LPS)” power supply unit when powering the device by an external DC power supply unit. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
-
Page 44: Connection And Login
11 (Windows 7) Microsoft Edge (Windows 10) Google Chrome Mozilla Firefox (latest available version of each browser) Browser settings JavaScript enabled Ethernet 100 Mbps Sound Sound card or on-board sound chip (min. 16 bit) Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... -
Page 45: Connection
➡ Enter the IP address of the device into the address bar of the web browser. ➡ Confirm the input. The connection to the device is then established. After a successful connection to the device, the login dialog is displayed. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... -
Page 46: Login
➡ Confirm with “OK”. After a successful login, the graphical user interface of the configuration mode is displayed. ➡ Configure all required settings. ➡ Finally, click “LOGOUT” to properly log out of the device. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... -
Page 47: Technical Product Specification (Basic Data)
• PoE (IEEE 802.3af) Power IN 1× Weidmüller male connector SL 3.50/02/90G (mating connector: Weidmüller plug-in connector BL 3.50/02/180 SN) Memory card slot 1× (microSDXC compatible) Additional Features Ambient light sensor 1× Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... - Page 48 Approx. 400 g (encoder unit with cable) Color Black with white housing ring Environmental Conditions Suitable installation sites Indoor Operating temperature −20 °C to +50 °C (−4 °F to 122 °F) Relative humidity 0 % – 90 % RH, non-condensing Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 49 The technical product specification (basic data) in this document is based on the information at the time of this document’s compilation. Detailed information and possible updates can be found in the currently valid product specification on www.dallmeier.com. Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
-
Page 50: Dimensions
MDF5400HD-DN Commissioning 14 Dimensions 37.10 mm 37.48 mm 48.76 mm Max. 18 mm Ø 23 mm Ø 94.60 mm Min. 9 mm Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com... - Page 51 Commissioning MDF5400HD-DN 130.65 mm 62 mm 94.05 mm 36.60 mm 41.50 mm 2 mm 57 mm 105 mm 12.50 mm 32 mm 57 mm 12.50 mm 5 mm 115 mm Rev. 1.0.1 | © 2018 Dallmeier | www.dallmeier.com...
- Page 52 Dallmeier electronic GmbH & Co.KG Bahnhofstr. 16 · 93047 Regensburg · Germany Phone +49 941 8700-0 · Fax +49 941 8700-180 www.dallmeier.com · info@dallmeier.com...