Table of Contents
Advertisement
Maintenance of other components
•
All nuts and bolts in the transmission including Rubber couplings, Star Drives, PTO Shafts and Gearboxes should
be checked for tightenes after mowing at the following intervals:
1st 40 hours
1st 100 hours
1st 250 hours
And every 250 hours thereafter.
•
Check blades on a regular basis for wear. Replace any damaged or worn parts immediately.
Rollers
Check the of condition of the roller ends at the end of every season. Roller end shaft must be able to rotate freely and
without excessive play. If necessary, remove the roller end and adjust the tightness of the bearings.
Replacement of wear parts
Blades, blade backs, blade bushing, blade bolts and nuts must be checked on a regular basis for wear and defection.
MAJOR recommends to visually check the blade assemblies every 40 hours of operation. This interval may change
depending on the operational conditions.
Replace any damaged or worn parts immediately, failure to do so can result in blade breakages and can cause
damage to the equipment or injuries to the operator and others nearby.
Blunt blades must be sharpened or replaced, failure to do so will result in a poor quality cut and excessive use of
power from your tractor.
Blade Rotation
Ensure blade rotation and timing (90 degrees) is correct after servicing transmission. See diagrams below.
6
6
BLADE ROTATION VIEWED
D
FROM UNDERSIDE
SWIFT ROTATIONS AS OF
D
JUNE 2018
400 SWIFT
MJ71-190
C
400 SWIFT
C
Date
Stock Code:
Rev.
Drawing No.
Scale
0
SW2-190-GA01
28/09/2017
Material:
REF DRWG
FAB
LAS
FIMP
LASF
PLA
MCD
PU
PLAF
IMP
B
B
A
A
6
SWIFT ROTATIONS AS OF
D
JUNE 2018
5
SWIFT ROTATIONS AS OF
5
4
JUNE 2018
400 SWIFT
CENTER BOX ROTATION
VIEWED FROM TOP,
C
LOOKING AT MACHINE
B
Quantity
Date
Stock Code:
Rev.
IF IN DOUBT ASK
0
THE INFORMATION CONTAINED IN THIS DRAWING IS THE PROPERTY
23/05/2017
Material:
MAJOR
REF DRWG
OF MAJOR EQUIPMENT INTL. LTD.
Vendor:
FAB
ANY REPRODUCTION IN PART OR A WHOLE WITHOUT THE WRITTEN
www.major-equipment.com
PERMISSION OF MAJOR EQUIPMENT INTL. LTD. IS PROHIBITED.
Route:
ASSY
Drawn
Title
Sheet
SR
190 SWIFT2
7 / 8
Finish:
SELF
10 FAB
47 PLATE C
PLATE Z
PAINT G
20 WELD
PLATE C
48 PLATE Z
PAINT Y
40 PAINT G
50 ASSY
GALV
GALVP G
42 PAINT Y
52 1FIX
SELF
WELD
45 GALV
55 2FIX
MJ71-400
A
Blade rotation viewed from underside
6
5
4
4
3
MJ71-240
IF IN DOUBT ASK
THE INFORMATION CONTAINED IN THIS DRAWING IS THE PROPERTY
MAJOR
OF MAJOR EQUIPMENT INTL. LTD.
Vendor:
FAB
ANY REPRODUCTION IN PART OR A WHOLE WITHOUT THE WRITTEN
www.major-equipment.com
PERMISSION OF MAJOR EQUIPMENT INTL. LTD. IS PROHIBITED.
Drawing No.
Scale
Route:
Drawn
Title
ASSY
2.4m SWIFT
SW2-240-GA01
SR
Finish:
SELF
FAB
LAS
10 FAB
47 PLATE C
PLATE Z
PAINT G
FIMP
LASF
20 WELD
PLATE C
48 PLATE Z
PAINT Y
MCD
PLA
40 PAINT G
50 ASSY
GALV
GALVP G
PLAF
PU
42 PAINT Y
52 1FIX
SELF
WELD
IMP
45 GALV
55 2FIX
Rear mounted machines shown
5
4
www.major-equipment.com
3
3
2
1
340 SWIFT
Sheet
7 / 8
MJ71-540
540 SWIFT
3
2
1
340 SWIFT
2
1
340 SWIFT
D
MJ71-340
540 SWIFT
C
540 SWIFT
B
2
1
13
A
D
D
C
C
B
B
A
A
Advertisement
Table of Contents
