Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FAAC 202025
Summary of Contents for FAAC 202025
- Page 1 E024 U Control Board UL325 - UL991 (800) 878-7829 www.FastGateOpeners.com...
-
Page 2: Technical Specifications
E024U CONTROL BOARD DESCRIPTION & CHARACTERISTICS SETTING DL14 DL15 DL16 DL17 DL18 DL19 DL20 DL21 DL22 Fig. A1 1.1 TECHNICAL SPECIFICATIONS 1.2 LAYOUT AND COMPONENTS Main power supply RADIO 115/230 V~ 50/60 Hz switchable Connector for the radio receiver Secondary power BATTERY 24 Vdc - 16 A max. -
Page 3: Input / Output Description
INPUT / OUTPUT DESCRIPTION B STP CL OP OPEN Fig. A2 LABEL FUNCTION 2 EASY 2 EASY Input for bus 2easy accessories (encoder) OPEN A N.O. Contact for total opening command OPEN B / OPEN B: N.O. Contact for opening of leaf 1 only CLOSE (with only one leaf the opening stops at 50% of traveling) CLOSE (LOGIC B-C): N.O. - Page 4 PHOTOCELLS CONNECTIONS How to connect Normally Open contacts. How to connect Normally Close contacts. (Connect them in parallel) (Connect them in series) Fig. A3 Fig. A4 The E024U board allows the connection of several safety devices (for example photocells). With photocells you can activate the FAILSAFE function, which, before each movement of the ope- rator, tests each fotocells.
- Page 5 Connection of two pairs of closing photocells STP CL OP Other optional safety devices to connect in series RX= Photocell Receiver TX= Ptotocell Transmitter CL= Closing OP= Opening To use the FAIL-SAFE mode connect the negative power supply of the transmitters to OUT (pin 9), and set dip-switch 11 and 12 to ON on DS1 When using the FAIL-SAFE mode also the safety inputs not used (FSW CL , FSW OP) must be connected Fig.
- Page 6 Connection of a pair of closing photocells and a pair of opening photocells STP CL OP RX= Photocell Receiver TX= Ptotocell Transmitter CL= Closing OP= Opening To use the FAIL-SAFE mode connect the negative power supply of the transmitters to OUT (pin 9), and set dip- switch 11 and 12 to ON on DS1 Fig.
-
Page 7: Operating Logic
PROGRAMMING 4.1 DIP SWITCH DS1 SETTINGS FOR OPERATING LOGIC OPERATING LOGIC DS 1: SW 1 - SW 2 - SW 3 PAUSE LOGIC DESCRIPTION TIME E (default) One command opens, the next one closes. A command du- OFF OFF OFF ring opening stops the gate Semiautomatic 0 - 4... - Page 8 4.2 ADJUSTING TRIMMERS – FORCE ADJUSTMENT MOTOR 1 Turn clockwise to increase the opening and closing force TR 2 – FORCE ADJUSTEMENT MOTOR 2 Turn clockwise to increase the opening and closing force TR 3 – SPEED ADJUSTMENT FOR MOTOR1 AND MOTOR 2 Turn clockwise to increase the opening and closing speed TR 4 –...
- Page 9 4.3 DIP SWITCH DS1 SETTINGS FOR BOARD SETUP BOARD SETUP DS 1: SW 4 to SW 12 The opening of leaf 2 is delayed after the opening of leaf 1. This is to avoid SW 4 OPENING DELAY that the gate’s leafs interfere with each other during the initial part of the 0 sec (default) movement.
-
Page 10: Led Diagnostics
4.4 DIP SWITCH DS2 SETTINGS FOR OPERATOR TYPE AND LOCK MODE SETTING DL 1 DL 2 DL 3 DL 4 DL 5 IMPORTANT DS 2 DS 2 OPERATOR SELECTION LOCK OUTPUT MODE OPERATOR TYPE SW 1 SW 2 SW 3 OUTPUT MODE SW 4 S450H, S800H... -
Page 11: Led Status
LED STATUS In BOLD the normal state with gate closed and working DESCRIPTION ON STEADY BLINKING Board working on AC Board working on LED BATTERY power battery power or ext Battery charging supply LED +24 Main power present Main power OFF SLOW BLINK (1 sec. -
Page 12: Led Error Display
The diagnostic LED shows only one error condition at a time, with the priority of the below table. In case there is more than one error once one is eliminated the LED will show the next LED ERROR DISPLAY NUMBER OF ERROR CONDITION SOLUTION FLASHES... -
Page 13: Obstacle Detection Function
AC connection At the point where you want the slowdown to start give an Power outlet OPEN A command with the push button or the remote that Power Supply and switch is already stored in memory. Leaf 2 starts to slow down and stops when it reaches the mechanical stop or FCA2. -
Page 14: Backup Battery
The E024U board is powered by a high efficiency switching power supply that takes 115V or 230V in input and provides 36VDC to power the board. The power supply is preset for 115V at the fac- tory, consult with FAAC Tecnical Support for 230V wiring options. 115V 230V... -
Page 15: Firmware Upgrade
10. FIRMWARE UPGRADE For the upgrade you need a USB Flash Drive, where you have to copy the file supplied by FAAC. Then follow these steps: The E024U board keeps the operating firmware in a field pro- grammable memory, it can be easily upgraded through the on Disconnect the batteries if they are present. - Page 16 LOGIC “S” PULSES SYSTEM STATUS OPEN A OPEN B CLOSE STOP FSW OP FSW CL FSW CL/OP opens released no effect no effect opens and closes no effect CLOSED leaf and closes no effect (OPEN disa- (OPEN disa- no effect after pause time (OPEN disabled) after pause time...
- Page 17 LOGIC “SP” PULSES SYSTEM STATUS OPEN A OPEN B CLOSE STOP FSW OP FSW CL FSW CL/OP opens and clo- opens leaf 1 and no effect no effect no effect CLOSED ses after pause closes after pause no effect (OPEN disa- no effect (OPEN disa- (OPEN disabled)
-
Page 18: Limited Warranty
FAAC S.p.A. intended provided it has been properly installed or FAAC International, Inc. The warranty herein and operated.