Hach BioTector B3500dw User Manual page 152

Check for possible build-up of salts or any material at any of the PFA T fittings located
between the Ozone Generator and the Mixer Reactor. Clean the fittings and/or the tubing if
necessary.
Remove Ozone Line Filter and wash it with DIW (or tap water). Dry the filter well and reinstall
in place. See figure 1, table 2 in Section
4.2.2 BioTector Sample Injection
Using the Simulate menu (see Section
and confirm that the pumps are pumping correctly.
Acid Pump rate for FMM20 Pump at 400 pulses should be between 3.80 ml and 4.20 ml.
(Depending on the quantity of the liquid injected into the reactor and due to an internal system interlock,
the system may request the activation of Reactor Purge cycle to purge any excess liquid from the
reactor. If necessary run "REACTOR PURGE" function in the Simulate menu.)
Base Pump rate for FMM20 Pump at 400 pulses should be between 3.80 ml and 4.20 ml.
Important Note: For the correct operation of the system, the measured Acid and Base Pump rates must
be identical or similar. The maximum allowable difference in the measured volumes for acid and base
injections above should not be more than 0.2ml.
Sample Pump rate for WMM60 Pump at 16 pulses should be between 5.5ml and 7.5ml in ~8
seconds.
(Any variation between these pumped volumes is corrected when the zero and span
calibration is carried out.)
Replace the 100mm filter mats in fan and vent housing (see item C4 in the service kit.)
Check the operation of the fan.
switches the fan off to stabilize system temperature using its own internal heat.)
Clean CO analyzer optics by removing the 4x M4x60 Allen bolts on the detector section. If
2
necessary, clean both lenses, which are located on the detector and the source section of
the CO Analyzer using the Lens Tissue (see item C5 in the service kits). Replace O-ring with
2
the 72-0325-30 O-ring provided (see item C6 in the service kit).
Oxygen Purity Test: Power up the system for at least 10 minutes before the oxygen purity
test is carried out. Using the Simulate menu (see Section
(see figure 2 and table 2 in Section
oxygen gas through the CO
analyzer zero reading (ppm CO2) should be within ±0.5% of full scale of the CO
range. For instance, if the CO
reading should be typically within ±50ppm. Go to CO2 Analyzer menu (see section
CO2 Analyzer) to view the CO
(If the CO analyzer zero reading is outside the specifications, confirm that there is no CO
2
oxygen gas by connecting the CO
analyzer inlet port and set the MFC to 10 l/h. As the size of the CO
flow running for at least for 5 minutes and record the CO
period. If the CO zero readings do not drop significantly with the CO
2
that there is no CO contamination in the oxygen supply.)
2
4.1.1 Analysis Enclosure
for details.
8.1.2 Simulate
(Note that at temperatures below 25°C, BioTector automatically
4.1.1 Analysis
analyzer for 5 minutes. At the end of this period, the CO
2
analyzer range is 10000ppm, then the CO
2
Analyzer Range.
2
filter "used with the base container" between the Cooler and CO
2
and figure 4 in Section
for details) and a 10ml graduated cylinder, check
8.1.2 Simulate) set the MFC
Enclosure) flow to 10 l/h and flow
filter is small, keep the 10 l/h gas
2
zero readings at the end of the 5 minute
2
filter in place, this will indicate
2
_____
_____
_____
_____
_____
_____
_____
_____
2
analyzer
2
analyzer zero
2
8.3.10
_____
in the
2
2
Page 152