Table of Contents Chapter 1................................1 1.1 Introducing the BIPAC 6300VNOZ........................1 1.2 Features of the BIPAC 6300VNOZ ........................3 Network Protocols and Features........................3 Firewall ................................3 Quality of Service Control..........................4 Wireless LAN..............................4 VoIP.................................4 USB Application Server ...........................4 IPTV Applications ............................4 Management ..............................4 1.3 Hardware Specifications..........................5 Physical Interface............................5 1.4 Applications for the BIPAC 6300VNOZ ......................6 Chapter 2................................7 2.1 Important note for using the BIPAC 6300VNOZ ..................7 2.2 Package Contents ............................8 2.3 The Front LEDs..............................9 2.4 The Rear Ports ............................11 2.5 Power Source .............................12 2.6 Cabling................................14 Chapter 3................................15 3.1 Before Configuration..........................15 3.1.1 Configuring a PC in Windows 7 ......................16 3.1.2 Configuring a PC in Windows Vista......................19 3.1.3 Configuring a PC in Windows XP ......................21 ...
Page 3
4.2.1 Device Info ............................31 4.2.2 System Log............................33 4.2.3 Statistics...............................34 4.2.4 DHCP Table ............................37 4.2.5 Disk Status ............................38 4.2.6 VoIP Status............................39 4.2.6.1 VoIP Status ............................39 4.3 Quick Start..............................40 4.4 Configuration..............................44 4.4.1 Interface Setup ............................45 4.4.1.1 Internet ............................45 4.4.1.2 LAN..............................49 4.4.1.3 Wireless............................53 4.4.1.4 Wireless MAC Filter ........................65 4.4.2 Advanced Setup...........................66 4.4.2.1 Firewall............................66 4.4.2.2 Routing............................67 4.4.2.3 NAT..............................69 4.4.2.4 Static DNS............................74 4.4.2.5 QoS..............................75 4.4.2.6 Interface Grouping........................76 4.4.2.7 Port Isolation..........................78 4.4.2.8 Time Schedule..........................79 4.4.3 VoIP..............................80 4.4.3.1 Basic ..............................81 4.4.3.2 Media ............................82 4.4.3.3 Advanced ............................83 4.4.3.4 Speed Dial .............................84 4.4.3.5 Call Features..........................85 4.4.4 Access Management..........................87 ...
Page 4
Problems starting up the router ......................111 Problems with the WAN Interface......................111 Problems with the LAN Interface......................111 Recovery procedures for non‐working routers ..................112 APPENDIX ................................113...
Introduction the BIPAC 6300VNOZ 1.1 Introducing the BIPAC 6300VNOZ Thank you for purchasing BIPAC 6300VNOZ Router. The BIPAC 6300VNOZ is a compact and advanced broadband gateway(router) that offers flexible and multiple internet connection services for home, SOHO and office users to enjoy high-speed, high-level security internet connection via cellular wireless and/or Ethernet WAN.
Page 6
easily which they get from ISP, then surf the Internet immediately. Firmware Upgradeable Device can be upgraded to the latest firmware through the WEB based GUI.
1.2 Features of the BIPAC 6300VNOZ • Gigabit Ethernet WAN (GbE WAN) for Fibre (FTTC/ FTTP/ FTTH) high WAN throughput • Gigabit Ethernet LAN • IPv6 ready (IPv4/IPv6 dual stack) • Multiple wireless SSIDs with wireless guest access and client isolation •...
Quality of Service Control • Traffic prioritization management based-on Protocol, Port Number and IP Address (IPv4/ IPv6) Wireless LAN • Compliant with IEEE 802.11 b/ g/ n standards • 2.4 GHz - 2.484GHz radio band for wireless • Up to 300 Mbps wireless operation rate •...
Page 9
• Web-based GUI for remote and local management (IPv4/ IPv6) • Firmware upgrades and configuration data upload and download via web-based GUI • Supports DHCP Server/ Client/ Relay • Supports SNMP v1, v2, v3. MIB-I and MIB-II TR-069* supports remote management •...
1.3 Hardware Specifications Physical Interface • Detachable antennas: 2 high performance external antennas • SIM Card slot: Mini SIM card (2FF) slot for mobile broadband connectivity • VoIP Phone port: 2 RJ-11 FXS for connecting to regular telephones • USB: 1 USB 2.0 type A port for storage service •...
BIPAC 6300VNOZ is embedded with a module supporting mobile SIM card. It can be used to connect to high speed mobile broadband connection. BiPAC 6300VNOZ also supports one USB ports for your mobile dongle. It can be used to connect to high speed mobile broadband connection, too.
Page 12
Broadband router mode BIPAC 6300VNOZ has a Gigabits Ethernet WAN port to connect to your Fibre/ Cable/ xDSL modem.
Do not use the same power source for the BIPAC 6300VNOZ as other equipment. Do not open or repair the case yourself. If the BIPAC 6300VNOZ is too hot, turn off the power immediately and have it repaired at a qualified service center. Warning ...
2.3 The Front LEDs Status Meaning Green System ready Power Boot failed Green AC working and battery OK Orange Only AC working, battery fail and has to change battery Battery Orange blinking AC fail and battery working The power input is from power adapter not UPS Green Transmission speed hitting 1000Mbps Orange...
Page 16
Green blinking quickly Signal strength 75% ~ 50% Orange blinking quickly Signal strength 50% ~ 25% Orange blinking slowly Signal strength < 25% Orange No signal, but module OK module fails or No module Obtaining IP failure Green Having obtained an IP address successfully Internet Router in bridged mode or WAN connection not present.
2.4 The Rear Ports Port Meaning Power source selector. Switch between DC power adapter and UPS (DC). Power Source Connect the supplied DC power adapter to this jack. After the device is powered on, press it 6 seconds or above: to restore to factory default settings (this is used when you can not login to the router, e.g.
2.5 Power Source 6300VNOZ offers two kinds of power input, namely, DC power Adapter and DC UPS (or BBU). 6300VNOZ can take the advantage of UPS (Uninterruptible Power Supply) to keep working even if the power outage hit your router when the router in working in DC UPS mode. (a picture of the rear focusing on the power source) (a shot from the front panel, with second icon being identified as the Battery LED) How to switch between the two power input:...
Page 19
The meanings of the different status of Battery LED: Green lit: AC is working, UPS battery working well Orange Lit: Only AC is working, but Battery fails. And you have to change battery Orange Blinking: AC fails, but battery is working...
Make sure that all other devices (e.g. telephones, fax machines, analogue modems) connected to the same telephone line as your Billion router have a line filter connected between them and the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and that all line filters are correctly installed in a right way.
The TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please refer to your Windows-related or other operating system manuals. Any TCP/IP capable workstation can be used to communicate with or through the BIPAC 6300VNOZ. To configure other types of workstations, please consult the manufacturer’s documentation.
3.1.1 Configuring a PC in Windows 7 Go to Start. Click on Control Panel. Then click on Network and Internet. When the Network and Sharing Center window pops up, select and click on Change adapter settings on the left window panel. Select the Local Area Connection, and right click the icon to select Properties.
Page 23
IPv4: Select Internet Protocol Version 4 (TCP/IPv4) then click Properties In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. Click OK again in the Local Area Connection Properties window to apply the new configuration.
Page 24
IPv6: Select Internet Protocol Version 6 (TCP/IPv6) then click Properties In the TCP/IPv6 properties window, select the Obtain an IPv6 address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. Click OK again in the Local Area Connection Properties window to apply the new configuration.
3.1.2 Configuring a PC in Windows Vista 1. Go to Start. Click on Network. Then click on Network and Sharing Center at the top bar. 2. When the Network and Sharing Center window pops up, select and click on Manage network connections on the left window pane.
Page 26
IPv4: 4. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 5. In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 6. Click OK again in the Local Area Connection Properties window to apply the new configuration.
3.1.3 Configuring a PC in Windows XP IPv4: 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties. 4.
Page 28
IPv6: IPv6 is supported by Windows XP, but you should install it first. Act as shown below: 1. On the desktop, Click Start > Run, type cmd, then press Enter key in the keyboard, the following screen appears. 2. Key in command ipv6 install Configuration is OK now, you can test whether it works ok.
3.1.4 Configuring a PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4.
3.1.5 Configuring a PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP ->NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC.
3.1.6 Configuring a PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK.
3.2 Factory Default Settings Before configuring your router, you need to know the following default settings. Web Interface: Username: admin Password: admin LAN Device IP Settings: IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 DHCP server: DHCP server is enabled. Start IP Address: 192.168.1.100 IP pool counts: 20 3.2.1 Username and Password The default username and password are “admin”...
3.3 LAN Port Addresses The parameters of LAN ports are pre-set in the factory. The default values are shown below. IPv4: 192.168.1.254 IP address 255.255.255.0 Subnet Mask Enabled DHCP server function 100 IP addresses continuing from 192.168.1.100 through IP addresses for distribution to PCs 192.168.1.199 3.4 Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of service...
Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “OK”, a user name and password window prompt will appear. The default username and password are “admin” and “admin”. Congratulation! You are now successfully logged on to the BIPAC 6300VNOZ!
Page 35
At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired setup page, including: Status(Device Info, System Log, Statistics, DHCP Table, Disk Status, VoIP Status) Quick Start (Wizard Setup) Configuration (Interface Setup, Advanced Setup, VoIP, Access Management, Maintenance) Language Please see the relevant sections of this manual for detailed instructions on how to configure your router.
4.2 Status In this section, you can check the router working status, including Device Info, System Log, Statistics, DHCP Table, Disk Status, and VoIP Status.
4.2.1 Device Info Users will see device's basic information in this page. EWAN...
Page 38
Device Information Model Name: Show model name of the router Firmware Version: This is the Firmware version MAC Address: This is the MAC Address IPv4: IP Address: LAN port IPv4 address. Subnet Mask: LAN port IP subnet mask. DHCPv4 Server: LAN port DHCP role - Enabled, Relay or Disabled. ...
4.2.2 System Log In system log, users can check the operations to the router and track the glitches to the router when occurred. Refresh: Press this button to refresh the statistics.
4.2.3 Statistics Ethernet Interface: This field displays the type of port Transmit Frames: This field displays the number of frames transmitted until the latest second. Transmit Multicast Frames: This field displays the number of multicast frames transmitted until the latest second.
Page 41
Wireless Transmit Frames: This field displays the number of frames transmitted until the latest second. Transmit Error Frames: This field displays the number of error frames transmitted until the latest second. Transmit Drop Frames: This field displays the number of drop frames transmitted until the latest second. Receive Frames: This field displays the number of frames received until the latest second.
Page 42
EWAN Transmit Frames: This field displays the total number of frames transmitted until the latest second. Transmit Multicast Frames: This field displays the total number of multicast frames transmitted till the latest second. Transmit Total Bytes: This field displays the total number of bytes transmitted until the latest second. Transmit Collision: This is the number of collisions on this port.
4.2.4 DHCP Table DHCP table displays the devices connected to the router with clear information. #: The index identifying the connected devices. Host Name: Show the hostname of the PC. IP Address: The IP allocated to the device. MAC Address: The MAC of the connected device. Expire Time: The total remaining interval since the IP assignment to the PC.
4.2.5 Disk Status Partition: Display the USB storage partition. Disk Space(KB): Display the total storage space of the NAS in KBytes unit. Free Space(KB): Display the available space in KBytes unit.
4.2.6 VoIP Status 4.2.6.1 VoIP Status VoIP status give users a directive picture on the registered VoIP accounts. Phone Number: The phone number user registers and fills in the Basic page of VoIP. Host: Show the IP address and port number of SIP Registrar. Status: The status of the registered SIP account.
4.3 Quick Start For detailed instructions on configuring WAN settings, see the Interface Setup section of this manual. The Quick Start Wizard is a useful and easy utility to help setup the device to quickly connect to your ISP (Internet Service Provider) with only a few steps required. It will guide you step by step to configure the password, time zone, and WAN settings of your device.
Page 47
Step3: Set your wireless connection. Click NEXT to continue.
Page 48
Step4: Set your Internet connection WAN Transfer Modes: EWAN EWAN 1). Select EWAN. Refer to your ISP to choose the appropriate connection protocol. Click NEXT to continue. Enter the PPPoE account information provided to you by your ISP. Click NEXT to continue. 3).The Setup Wizard has completed.
Page 49
Switch to Status > Device Info to view the status. ...
4.4 Configuration Click this item to access the following sub-items that configure the router: Interface Setup, Advanced Setup, VoIP, Access Management, and Maintenance.
4.4.1 Interface Setup First, let us take a look at the Interface Setup. There are four items contained in this section, namely, Internet, LAN, Wireless and Wireless MAC Filter. Each is described in the following scenario. 4.4.1.1 Internet EWAN...
Page 52
Multi Service Service Index: The index to mark the EWAN interface of different ISP type, ranging from 0-7. Service Summary: The diagram for view of service information. Status: Select whether to enable the service. IPv4/IPv6 IP version: choose IPv4, IPv4/IPv6, IPv6 based on users’ environment. Here we take IPv4/IPv6 for example, when you just choose IPv4 or IPv6, you can just get information from the following listed parameters.
Page 53
working in the internet. Connection Setting Connection: Always On: Click on Always On to establish a PPPoE session during start up and to automatically re-establish the PPPoE session when disconnected by the ISP. Connect Manually: Select Connect Manually when you don't want the connection up all the time. TCP MSS Option: Enter the TCP Maximum Segment Size (MSS).
Page 54
When router’s Internet configuration is finished successfully, you can go to status to get the connection information.
4.4.1.2 LAN A Local Area Network (LAN) is a shared communication system to which many computers are attached and is limited to the immediate area, usually the same building or floor of a building. IPv6 The IPv6 address composes of two parts, thus, the prefix and the interface ID. There are two ways to dynamically configure IPv6 address on hosts.
Page 56
IPv4 Parameters IP Address: Enter the IP address of Router in dotted decimal notation, for example, 192.168.1.254 (factory default). IP Subnet Mask: The default is 255.255.255.0. User can change it to other such as 255.255.255.128. Alias IP Address: This is for local networks virtual IP interface. Specify an IP address on this virtual interface. Alias IP Subnet Mask: Specify a subnet mask on this virtual interface.
Page 57
If set to Disabled, the DHCP server will be disabled. If set to Relay, the BIPAC 6300VNOZ acts as a surrogate DHCP server and relays DHCP requests and responses between the remote server and the clients. Enter the IP address of the actual, remote DHCP server in the Remote DHCP Server field in this case.
Page 58
IPv6 parameters Interface Address / Prefix Length: enter the static LAN IPv6 address, we suggest leave the field empty because when setted wrong, it will result in LAN devices not being able to access other IPv6 device through internet. Router will take the same WAN’s prefix to LAN side if the field is empty. MLD Snooping: Similar to IGMP Snooping, but applicable for IPv6.
4.4.1.3 Wireless This section introduces the wireless LAN and some basic configurations. Wireless LANs can be as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to the wired LAN.
Page 60
Access Point Settings Access Point: Default setting is set to Activated. If you want to close the wireless interface, select Deactivated. AP MAC Address: The MAC address of wireless AP. Wireless Mode: The default setting is 802.11b+g+n (Mixed mode). If you do not know or have both 11g and 11b devices in your network, then keep the default in mixed mode.
Page 61
WPS Settings WPS (Wi-Fi Protected Setup) feature is a standard protocol created by Wi-Fi Alliance. This feature greatly simplifies the steps needed to create a Wi-Fi networks for a residential or an office setting. WPS supports 2 types of configuration methods which are commonly known among consumers: &...
Page 62
3. Launch the wireless client’s WPS utility (eg. Ralink Utility). Set the Config Mode as Enrollee, press the WPS button on the top bar, select the AP (eg. Billion_AP) from the WPS AP List column. Then press the PIN button located on the middle left of the page to run the scan.
Page 63
4. The client’s SSID and security setting will now be configured to match the SSID and security setting of the registrar (router).
Page 64
PIN Method: Configure AP as Enrollee 1. Jot down the WPS PIN (eg. 03454435).Press Start WPS.
Page 65
2. Launch the wireless client’s WPS utility (eg. Ralink Utility). Set the Config Mode as Registrar. Enter the PIN number in the PIN Code column then choose the correct AP (eg. Billion_AP) from the WPS AP List before pressing the PIN button to run the scan.
Page 66
3. The router’s (AP’s) SSID and security setting will now be configured to match the SSID and security setting of the registrar (client). 4. Now to make sure that the setup is correctly done, cross check to see if the SSID and the security setting of the registrar setting match with the parameters found on both Wireless Configuration and Wireless Security Configuration page.
Page 67
PBC Method: 1. Press the PBC radio button, Then Start WPS. 2. Launch the wireless client’s WPS Utility (eg. Ralink Utility). Set the Config Mode as Enrollee. Then press the WPS button and choose the correct AP (eg. Billion_AP) from the WPS AP List section before pressing the PBC button to run the scan.
Page 68
3. When the PBC button is pushed, a wireless communication will be established between your router and the PC. The client’s SSID and security setting will now be configured to match the SSID and security setting of the router.
Page 69
Security Settings Security Type: You can disable or enable wireless security for protecting wireless network. The default type of wireless security is OPEN and to allow all wireless stations to communicate with the access points without any data encryption. To prevent unauthorized wireless stations from accessing data transmitted over the network, the router offers secure data encryption, known as WEP and WPA.
Page 70
WPA-PSK & WPA2-PSK WPA Algorithms: TKIP (Temporal Key Integrity Protocol) or AES (Advanced Encryption System) utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers. Pre-Shared key: The key for network authentication. The input format should be 8-63 ASKII characters or 64 hexadecimal characters Key Renewal Interval: The time interval for changing the security key automatically between wireless client and AP.
4.4.1.4 Wireless MAC Filter The MAC filter screen allows you to configure the router to give exclusive access to up to 8 devices (Allow Association) or exclude up to 8 devices from accessing the router (Deny Association). Every Ethernet device has a unique MAC (Media Access Control) address.
4.4.2 Advanced Setup Advanced Step provides some advanced features including Firewall, Routing, NAT, Static DNS, QoS, Internet Grouping, Port Isolation and Time Schedule for all advanced users. Please move on to have a picture of what the exact feature is about and how to use it. 4.4.2.1 Firewall Your router includes a firewall for helping to prevent attacks from hackers.
4.4.2.2 Routing This is static route feature. You are equipped with the capability to control the routing of all the traffic across your network. With each routing rule created, user can specifically assign the destination where the traffic will be routed to.
Page 74
ADD Route Destination IP Address: This is the destination subnet IP address. Destination Subnet Mask: The subnet mask of destination network. Gateway IP Address/Interface:This is the gateway IP address or existing interface to which packets are to be forwarded. Metric:It represents the cost of transmission for routing purposes. The number need not be precise, but it must be between 1 and 15.
4.4.2.3 NAT The NAT (Network Address Translation) feature transforms a private IP into a public IP, allowing multiple users to access the internet through a single IP account, sharing the single IP address. NAT break the originally envisioned model of IP end-to-end connectivity across the internet so NAT can cause problems where IPSec/ PPTP encryption is applied or some application layer protocols such as SIP phones are located behind a NAT.
Page 76
The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming packets will be checked by the Firewall and NAT algorithms then passed to the DMZ host, when a packet received does not use a port number used by any other Virtual Server entries. DMZ for: Indicate the related WAN interface which allows outside network to connect in and communicate.
Page 77
Virtual Server In TCP/IP networks a port is a 16-bit number used to identify which application program (usually a server) incoming connections should be delivered to. Some ports have numbers that are pre-assigned to them by the IANA (the Internet Assigned Numbers Authority), and these are referred to as “well-known ports”. Servers follow the well-known port assignments so clients can locate them.
Page 78
Local IP Address: Enter your server IP address in this field. Start Port Number (Local): Please enter the start port number of the local application (service). End Port Number (Local): Please enter the end port number of the local application (service). Examples of well-known and registered port numbers are shown below.
Page 79
Some tips for using DMZ and Virtual Server: Using port forwarding does have security implications, as outside users will be able to connect to PCs on your network. For this reason you are advised to use specific Virtual Server entries just for the ports your application requires, instead of using DMZ.
4.4.2.4 Static DNS The Domain Name System (DNS) is a hierarchical naming system built on a distributed database for computers, services, or any resource connected to the Internet or a private network associates various information with domain names assigned to each of the participating entities. Most importantly, it translates domain names meaningful to humans into the numerical identifiers associated with networking equipment for the purpose of locating and addressing these devices worldwide.
4.4.2.5 QoS QoS helps you control the upload traffic of each application from LAN(Ethernet and/or Wireless) to WAN (Internet). It facilitates you the features to control the quality of throughput for each application. This is useful when there on certain types of data you want giver higher priority to, such as voice data packets given higher priority than web data packets.
4.4.2.6 Interface Grouping Interface grouping is a function to group interfaces, known as VLAN. A Virtual LAN, commonly known as a VLAN, is a group of hosts with the common set of requirements that communicate as if they were attached to the same broadcast domain, regardless of the physical location.
Page 83
You are going to group the ports and services into two working group, as shown below. Group Index Group Port EWAN0,LAN1, LAN2, WLAN1 EWAN1, LAN3 Click Group Summary to show the configuration results.
4.4.2.7 Port Isolation Port isolation is a mechanism to allow or block devices in one port (indicates the LAN1 - LAN3 and WLAN1 - WLAN4, need to enable multiple SSID in wireless section) to access other devices in other ports. By default, all ports (LAN port and WLAN port) are sharing one group, and devices in all these ports can have access to each other.
4.4.2.8 Time Schedule The Time Schedule supports up to 16 timeslots which helps you to manage your Internet connection. In each time profile, you may schedule specific day(s) i.e. Monday through Sunday to restrict or allowing the usage of the Internet by users or applications. This Time Schedule correlates closely with router’s time, since router does not have a real time clock on board;...
4.4.3 VoIP VoIP, or Voice over Internet Protocol, enables telephone calls through existing internet connections instead of going through the traditional PSTN (Public Switched Telephone Network). It is not only cost-effective, especially for a long-distance call, but also top quality voice calls over the internet. Five sub-items to be covered to configure the VoIP feature, namely Basic, Media, Advanced, Speed Dial, Call Features.
4.4.3.1 Basic Register to a SIP service provider is an essential step before making the VoIP call. Users can find out SIP service provider, and register a SIP account, jotting down the registration information and configuring in router. Locale RTP Port: Set the local RTP port used to receive voice packet. The setting is to be applied to the two FXS, name phone 1 and phone 2, and the two FXS share the same local RTP port.
4.4.3.2 Media Media offers for kinds of codec, G.711 u-law, G.711 A-law, G.729, G.726, from greatest to lowest in priority. Phone: Select to set the following configurations for Phone 1 or Phone2. When phone1 is selected, the following set media codec will be applied to phone1. ...
4.4.3.3 Advanced Advance section equipement the users with the ability to do some advanced settings to each phone port. Go on to see. Region: Select the exact region from the drop-down menu to adjust the phone custom in the exact region, like ring tone, busy tone, dial tone, etc, as different regions may have different phone using traditions.
4.4.3.4 Speed Dial Speed Dial comes at hand to store frequently used telephone number(s) that you can press set ‘speed dial number’ instead of the exact dialing-out number on the phone keyboard to make a quick dialing. Index: The index to mark the speed dial number mapping, 0-9. Phone: Select Phone 1 or Phone 2 to have your set speed dial number applied to the phone.
4.4.3.5 Call Features Call Features provides usrs with some advanced phone characteristics, including Call waiting, Conference Call, etc. Phone: Select the phone 1 or Phone 2 to have the following characteristics applied to the phone. Call Waiting: Enable to activate Call Waiting feature. When you are busy on a call with, for example, A, and another call comes in, B, while the Call Waiting feature is enabled, you can hear a hint sound indicating there is another call in for you to decide to answer B by slightly pressing Hook to keep the original call with A.
Page 92
How to establish 3-way conference call Case 1: Bill and Larry are talking. Bill wants to invite Mark to join a conference call. Step – 1: Billy and Larry are discussing on the phone. Bill tells Larry that he wants to set up a conference call with Mark.
4.4.4 Access Management 4.4.4.1 Device Management Device management offers users a way to change the embeded web server accessing port, default 80. User can change the http port to 8080 or something else here.
Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. BIPAC 6300VNOZ serves as a SNMP agent which allows a manager station to manage and monitor the router through the network.
Auto-configured: Select this check box to allow UPnP-enabled applications to automatically configure the BIPAC 6300VNOZ so that they can communicate through the BIPAC 6300VNOZ, for example by using NAT traversal, UPnP applications automatically reserve a NAT forwarding port in order to communicate with another UPnP enabled device;...
Dynamic DNS: Select this check box to activate Dynamic DNS. Service Provider: Select from drop-down menu for the appropriate service provider, for example: www.dyndns.org. My Host Name: Type the domain name assigned to your BIPAC 6300VNOZ by your Dynamic DNS provider. Username: Type your user name.
Page 97
User can register a DDNS Examples: first users have to go to the Dynamic DNS registration service provider to register an account. Note User test1 register a Dynamic Domain Names in DDNS provider http://www.dyndns.org/ DDNS: www.hometest.com using username/password test/test...
Active: Select to activate the rule. Secure IP Address: The default 0.0.0.0 allows any client to use this service to manage the BIPAC 6300VNOZ. Type an IP address range to restrict access to the client(s) without a matching IP address.
Page 99
By default, the “Access Control” has two default rules. 1. Rule 1(Index 1), a rule to allow only clients from LAN to have access to all embedded applications (Web, FTP, etc). Under this situation, clients from WAN can not access the router even from Ping. 2, Rule 2(Index 2), a ACL rule to open Ping to WAN side.
4.4.4.6 Packet Filter You can filter the packages by MAC address, IP address, Protocol, Port number and Application or URL. IP & MAC Filter Packet Filter Filter Type: There are three types “IP & MAC Filter”, “Application Filter”, and “URL Filter” that user can select for this filter rule.
Page 101
Source Port Number: The source port number of packets to be monitored. 0 means “Don’t care”. Destination IP Address: The destination IP address of packets to be monitored. 0.0.0.0 means “Don’t care”. Destination Subnet Mask: Enter the subnet mask of the destination network. Destination Port Number: This is the Port that defines the application.
Page 102
Application Filter Application Filter: Select this option to Activated/Deactivated the Application filter. ICQ: Select this option to Allow/Deny ICQ. MSN: Select this option to Allow/Deny MSN. YMSG: Select this option to Allow/Deny Yahoo messenger. Real Audio/Video(RTSP): Select this option to Allow/Deny Real Audio/Video (RTSP).
Page 103
URL Filter URL Filter: Select Activated to enable URL Filter. URL Filter Rule Index: This is item number. Individual Active: To give control to the specific URL access individually, for example, you want to prohibit access to www.yahoo.com, please first press Activated in “URL Filter” field, and also Yes in “Individual Active” field;...
4.4.4.7 CWMP (TR-069) CWMP, short for CPE WAN Management Protocol, also called TR069 is a Broadband Forum technical specification entitled CPE WAN Management Protocol (CWMP). It defines an application layer protocol for remote management of end-user devices. It defines an application layer protocol for remote management of end-user devices.
Page 105
Periodic Inform Config Periodic Inform: Select activated to enable to let CPE be authorized to send Inform message to automatically connect to ACS. Interval(s): Specify the inform interval time (sec) which CPE used to periodically send inform message to automatically connect to ACS. When the inform interval time arrives, the CPE will send inform message to automatically connect to ACS.
4.4.4.8 Parental Control With this feature, router can reject to provide internet services to the specified computer during some specified time interval. This can be very useful for parents to give control to children using computer without restraint. Parent Control: Select Activated to enable this feature. MAC Address: Type the MAC address(es) you want to block to access the internet (access to the router is sustained).
4.4.4.9 SAMBA & FTP Server Samba and FTP are served as network sharing. SAMBA Server: Activated to enable SAMBA sharing. Work Group: The same mechanism like in Microsoft work group, please set the Work Group name. NetBIOS Name: The sharing NetBIOS name. FTP Server: Activated to enable FTP sharing.
Page 108
Samba Usage: 1. Go directly to Start > Run (enter \\192,168,1,254 (from LAN side), \\SambaSvr , but if you enter \\SambaSvr, please be sure your working PC is in the same workgroup as set in the samba server set above.) 2.
Page 109
FTP usage: 1. Access via FTP tools Take popular FTP tool of FlashFXP for example: 1) Open FlashFXP 2) Create ftp sites (LAN IP / WAN IP, 192.168.1.254, and set the account, port). 3) Connect to the ftp site.
Page 110
2. Web FTP access 1) Enter ftp://192.168.1.254 at the address bar of the web page. 2) Enter the account's username and password.
4.4.5 Maintenance Maintenance equipments the users with the ability of maintaining the device as well as examining the connectivity of the WAN connections, including User Management, Time Zone, Firmware & Configuration, System Restart, Diagnostic Tool. Usage of each feature is to be presented in the following scenarios. 4.4.5.1 User Management In factory setting, the default accounts are admin/admin and user/user.
SAMBA Authority SAMBA Access: Enable to grant the user access to the SAMBA server. Permission: Set the operation permission for the user, Read/Write or Read. 4.4.5.2 Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server outside your network.
To upgrade the firmware of BIPAC 6300VNOZ, you should download or copy the firmware to your local environment first. Press the “Browse…” button to specify the path of the firmware file. Then, click “Upgrade”...
Page 114
UPGRADE: Click UPGRADE to begin the upload process. This process may take up to two minutes. DO NOT power down the router or interrupt the firmware upgrading while it is still in process. Improper operation could damage the router. Warning...
4.4.5.4 System Restart Click System Restart with option Current Settings to reboot your router. If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to restore to factory default settings. You may also restore your router to factory settings by holding the small Reset pinhole button on the back of your router in about more than 6s seconds whilst the router is turned on.
4.4.5.5 Diagnostics Tool The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides. EWAN: Click START to begin to diagnose the connection.
Chapter 5 Troubleshooting If the router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems starting up the router Problem Corrective Action...
Recovery procedures for non-working routers Problem Corrective Action 1. Power on the router, once the Power LED lit red, please press this reset button Recovery procedures using the end of paper clip or other small pointed object immediately. for non-working routers(e.g.
Most problems can be solved by referring to the Troubleshooting section in the User’s Manual. If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer where you purchased this product. Contact Billion WORLDWIDE http://www.billion.com MAC OS is a registered Trademark of Apple Inc.
Page 120
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Need help?
Do you have a question about the BiPAC 6300VNOZ and is the answer not in the manual?
Questions and answers