Making Frothed Milk (Without Coffee); Changing The Quantity Of Coffee And Milk For Cappuccino - Smeg CMS6451X Manual

Hide thumbs Also See for CMS6451X:
Table of Contents

Advertisement

cappuccino by pressing the
Remove the lid of the milk container.
Fill the container with about 100 grams of milk for each
cappuccino to be prepared (fig. 19). Never exceed the MAX
level (corresponding to about 750 ml) marked on the jug.
You should ideally use skimmed or semi-skimmed milk at
refrigerator temperature (about 5°C).
Make sure the intake tube is correctly inserted in the rub-
ber washer (fig. 20) then replace the milk container lid.
Position the frothed milk regulator (B1) between the
words CAPPUCCINO and CAFFELATTE printed on the milk
container lid.
The quality of froth can be adjusted by moving the frothed
milk regulator towards the word CAFFELATTE for a denser
froth.
Moving it towards the word CAPPUCCINO obtains a less
dense froth.
NO schiuma
Schiuma
"più compatta"
Cursore
Schiuma "meno densa"
Remove the hot water spout (fig 21) and attach the milk
container to the nozzle (fig. 22).
Position the milk tube as shown in fig. 23 and then place a
sufficiently large cup under the coffee and milk spouts.
Turn the knob (C11) to the right.
"CAPPUCCINO..." is displayed and after a few seconds, fro-
thed milk flows out of the milk spout into the cup below.
(Delivery stops automatically).
The appliance then grinds the beans, delivers the coffee
and displays the "ready" message again.
The cappuccino is now ready. Sweeten to taste and, if desi-
red, sprinkle the froth with a little cocoa powder.
NOTE 1: While making cappuccino, the flow of frothed milk or
coffee can be interrupted by turning the
right.
NOTE 2: If the milk in the container finishes while delivering fro-
thed milk, remove the container and add milk.
Then re-attach it and turn the
request cappuccino again.
NOTE 3: To ensure the complete cleanliness and hygiene of the
milk frother, always clean the circuits in the milk container lid
after making cappuccino
Place a recipient under the milk spout;
Press the CLEAN button on the lid and hold down for at le-
button (C7).
knob (C11) to the
knob (C11) to the right to
ast 3 seconds (fig. 25). The appliance displays " CLEANING".
After cleaning, remove the milk container and place in the
refrigerator.
The milk should not be left out of the refrigerator for more
than 15 minutes.
NOTE 4: To change the quantity of coffee or frothed milk the
appliance delivers automatically into the cup, proceed as descri-
bed in the section "Changing the quantity of coffee and milk for
cappuccino".

MAKING FROTHED MILK (WITHOUT COFFEE)

Remove the lid of the milk container.
Fill the container with the quantity of milk you want to
prepare (fig. 19).
Replace the lid on the milk container.
Attach the milk container to the appliance (fig. 22).
Place a sufficiently large cup under the spout (fig. 23).
Turn the
knob (C11) to the left.
"FROTHED MILK" is displayed and after a few seconds, fro-
thed milk flows out of the milk spout into the cup below.
After delivery, clean the tubes inside the milk container
by pressing the CLEAN button as described in the previous
section (note 3).
CHANGING THE QUANTITY OF COFFEE AND MILK
FOR CAPPUCCINO
The appliance is set by default to automatically deliver a stan-
dard cappuccino.
To change these quantities, proceed as follows:
Fill the container with milk up to the maximum level indi-
cated on the container.
Turn the
knob (C11) to the right and keep it turned for
at least 3 seconds until "MILK FOR CAPPUCCINO PROGRAM
QUANTITY" is displayed. Release the knob.
The appliance starts delivering milk.
Once the required quantity of milk has been delivered, turn
the knob (C11) to the right again. Milk delivery stops.
(You should not deliver frothed milk for more than 3 minu-
tes at a time.)
After a few seconds, the appliance delivers coffee into the
cup and displays "COFFEE FOR CAPPUCC. PROGRAM QUAN-
TITY".
Once the required quantity of coffee has been delivered,
turn the
knob (C11) to the right again. Coffee delivery
stops.
The appliance is now re-programmed with the new settings and
displays: READY.
15

Advertisement

Table of Contents
loading

Table of Contents