Related Manuals for Smeg CMSU6451X
Summary of Contents for Smeg CMSU6451X
- Page 1 INSTRUCTIONS MODE D’EMPLOI MANUAL DE INSTRUCCIONES COFFEE AND CAPPUCCINO MAKER MACHINE À CAFÉ ET À CAPPUCCINO CAFETERA PARA CAFÉ Y CAPUCHINO...
-
Page 2: Table Of Contents
CONTENTS Changing coffee temperature ..........19 Changing the length of time the appliance remains on ..19 INTRODUCTION ............7 Setting water hardness ............19 Symbols used in these instructions ..........7 Resetting default values (reset) ..........19 Letters in brackets ..............7 Washing procedure ..............19 Troubleshooting and repairs ............7 CHANGING THE LANGUAGE ........ -
Page 3: Introduction
IMPORTANT SAFEGUARDS INTRODUCTION Thank you for choosing the automatic coffee and cappuccino When using electrical appliances, basic safety precau- maker. We hope you enjoy using your new appliance. tions should always be followed including the following: Take a few minutes to read these instructions. This will avoid all risks and damage to the machine. -
Page 4: Designated Use
system of the house checked by a qualified electri- nozzle or the hot water dispenser. The machine must cian. The manufacturer can not be held responsible never be used to clean objects. for damages caused by the lack, or inadequacy, of an •... -
Page 5: Description Of Milk Container And Accessories
A5. Infuser C10. button to deliver one or two cups of long coffee A6. Lights C11. knob to deliver cappuccino or frothed milk A7. Control panel A8. Hot water and steam nozzle PRELIMINARY CHECKS A9. Water tank Controls after transport A10. -
Page 6: Built-In Installation
light up the spout and cup tray. The lights stay on until the appliance is turned off. While coffee, steam or hot water is being delivered, the cooling fan comes on. At the end of the function, the cooling fan remains on to avoid condensation forming inside the cabinet. - Page 7 x 16 x 16 x 16 x 16 Position the rails on the sides of the cabinet as shown in the figure. Fix with the screws, then extract them completely. Position the appliance on the rails, making sure the pins are If the coffee maker is installed over a warmer drawer (500 W correctly inserted in the housings, then fix it with the screws max.), use the top surface of this as a reference to position the...
-
Page 8: Using The Appliance For The First Time
USING THE APPLIANCE FOR THE FIRST TIME right or left. • Coffee has been used to factory test the appliance and it is TURNING ON AND HEATING UP therefore completely normal for there to be traces of coffee in the mill. Each time the appliance is turned on, it performs an automatic The machine is, however, guaranteed to be new. -
Page 9: Changing The Quantity Of Coffee In The Cup
Take care to avoid scalds). NOTE 1: If the coffee is delivered a drop at a time or not at all, turn the grinding adjustment knob (fig. 12) one click clockwise (see “Adjusting the coffee mill”). Proceed one click at a time until coffee delivery is satisfactory. NOTE 2: If the coffee is delivered too fast and the cream is not satisfactory, turn the grinding adjustment knob (fig. -
Page 10: Ajusting The Coffee Mill
ADJUSTING THE COFFEE MILL enable the coffee mill. NOTE 1: Never introduce pre-ground coffee when the machine is The coffee mill is preset in the factory to make coffee correctly off or it could spread through the inside of the appliance. and should not require adjusting initially. -
Page 11: Making Frothed Milk (Without Coffee)
• Remove the lid of the milk container. least 3 seconds (fig. 25). The appliance displays “CLEAN- • Fill the container with about 100 grams / 0.22 lb of milk ING”. for each cappuccino to be prepared (fig. 19). Never exceed After cleaning, remove the milk container and place in the the MAX level (corresponding to about 750 ml / 25.36 oz) refrigerator. -
Page 12: Cleaning And Maintenance
CLEANING AND MAINTENANCE To remove the tray: 1. Open the service door (A2) (fig. 14). Before performing any cleaning operations, leave the machine 2. Remove the drip tray (A11) and the grounds container (A4) to cool down completely and unplug from the mains power (fig. -
Page 13: Cleaning The Milk Container
Cleaning the milk container 2. Open the service door (A2) (fig. 14). 3. Remove the drip tray (A11) and grounds container (fig. 15). 4. Press the two red release buttons inwards and at the same Important! Always clean the tubes inside the milk time pull the infuser outwards (fig. -
Page 14: Setting The Clock
• DESCALE NO relating to the procedure to follow in the event of contact with • TEMPERATURE MEDIUM the skin and eyes. • OFF AFTER 1 HOUR N:B:: Use the descaler recommended by the manufac- • WATER HARDNESS 4 turer only. Use of other descalers invalidates the guarantee. •... -
Page 15: Changing Coffee Temperature
• Press the OK button (C5) and refill the water tank with from its packaging then dip it fully in the water for a few clean water. seconds, • The descale programme is now terminated and the appli- Then remove and wait about 30 seconds (until it changes ance is ready to make coffee again. -
Page 16: Technical Specification
N.B.: If the appliance is not used for an extended period, place the main switch (A19) on the back of the appliance in the 0 position. TECHNICAL SPECIFICATION Voltage: 220-240 V~ 50/60 Hz max. 10A Absorbed power: 1350W Pressure: 15 bars Water tank capacity: 1.7 litres / 57.48 oz Size LxHxD: 595 x 455 x 412 mm / 23.43 x 17.91 x 16.22 in Weight: 26 kg / 57.32 lb... -
Page 17: Displayed Messages
DISPLAYED MESSAGES DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY FILL TANK The water tank is empty or positioned Fill the tank with water and/or insert it incorrectly. correctly, pushing it as far as it will go. GROUND TOO FINE ADJUST MILL The grinding is too fine and the coffee is Turn the grinding adjustment knob one Insert water spout and press OK (C5) delivered too slowly. -
Page 18: Troubleshooting
TROUBLESHOOTING If the problem cannot be resolved as described, contact Custom- er Services. Below is a list of some of the possible malfunctions. PROBLEM POSSIBLE CAUSE REMEDY The coffee is not hot. The cups were not preheated. Heat the cups by rinsing them in hot wa- ter or leaving them to rest for at least 20 minutes on the cup warmer tray. -
Page 19: Recipes
PROBLEM POSSIBLE CAUSE REMEDY The milk contains bubbles or squirts out The milk is not cold enough or is not You should ideally use skimmed or semi- of the milk spout. semi-skimmed. skimmed milk at refrigerator tempera- ture (about 5°C / 41°F). If the result is still disappointing, try another brand of milk. - Page 20 C9 C10...
- Page 23 SMEG S.p.A. Via Leonardo Da Vinci, 442016 Guastalla (RE) Italia www.smeg.com...