NEC MultiSync V554Q-R User Manual page 55

Mail Setting
Click on "MAIL" on the left column below HOME.
When the Mail settings are configured and enabled, the monitor sends email notifications when an error occurs or if the input
signal is lost. The monitor must be connected to a LAN for this feature to work.
ALERT MAIL When an error occurs, the monitor will send an error message to the email address(es) listed in the
Recipient's Address fields. Please see the "Alert error message list" table below.
Note that it is not an error when no input signal is detected. The monitor will only send a no signal
input notification email when Status Message is enabled.
Selecting [ENABLE] turns on the Alert Mail feature.
Selecting [DISABLE] turns off the Alert Mail feature.
STATUS MESSAGE When there is no input signal, the monitor will send a no signal detected notification to the email
address(es) listed in the Recipient's Address fields.
Note that this option does not send notifications of any errors that occur. The monitor will only send
error notifications when Alert Mail is enabled.
Selecting [ENABLE], Alert Mail send mails when the monitor is no signal or in alerting conditions.
Selecting [DISABLE], Alert Mail send mails when the monitor is in alerting conditions.
It doesn't send mail when the monitor is no signal.
SENDER'S ADDRESS Type in the sender's address. Up to 60 alphanumeric and symbols characters can be used.
SMTP SERVER Type in the SMTP server name to be connected with the monitor.
Up to 60 alphanumeric characters can be used.
RECIPIENT'S Type in your recipient's address. Up to 60 alphanumeric and symbols characters can be used.
ADDRESS 1 TO 3
AUTHENTICATION This selects the authentication method of the email transmission.
METHOD
POP3 SERVER This specifies the address of the POP3 server that is used in the authentication of the email.
USER NAME This sets the user name for logging into the authentication server when authentication is required
for the email transmission. Up to 60 alphanumeric characters can be used.
PASSWORD This sets the password for logging into the authentication server when authentication is required for
the email transmission. Up to 60 alphanumeric characters can be used.
TEST MAIL Click on this button to send a test email to check if your settings are correct.
NOTE:
• If an alert email isn't received when performing a Test Mail, check that the network, server settings and the
recipient's email address are correct.
• If you entered an incorrect address in a test, you may not receive an Alert email.
Should this happen, check that the Recipient's Address is correct.
HINT: For the control command diagram, please see the file "External_Control.pdf" on the CD-ROM supplied with this
monitor.
Alert error message list
Error number
Alert mail Message
* ErrorCode
The monitor's power supply is not
70h ~ 7Fh
functioning normally.
80h ~ Fh The cooling fan has stopped.
The monitor's backlight unit is not
90h ~ 9Fh
functioning normally.
A0h ~ AFh The monitor is overheated.
A2h
The monitor does not receive an input
B0h ~ BFh
signal.
The remaining capacity of the error log
D0h
decreased.
The battery for clocks is empty.
D1h
E0h ~ EFh A system error occurred in the monitor. System error.
Explanation
Standby power abnormal
Cooling fan abnormal
Backlight abnormal
Temperature abnormal
A Sensor reached the temperature limit
which was specified in the OSD.
*Condition: [DISPLAY PROTECTION]-[FAN
CONTROL]-[COOLING FAN] = [AUTO]
No signal
The Proof of Play log memory size is 1 more
hour.
The battery is empty.
English-53
Measure
Please contact your supplier.
Please contact your supplier.
Please contact your supplier.
Please contact your supplier.
Reconfirm the settings in the OSD
[DISPLAY PROTECTION]-[FAN
CONTROL] or please contact your
supplier.
Please check "No picture" in
"Troubleshooting".
Please get a log by using PD
external command. See page 59.
Please connect the monitor to the
power then recharge the battery.
Please set [DATE & TIME] in OSD.
Please contact your supplier.