Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ACME Ellipsoidal E-300 D2550
Summary of Contents for ACME Ellipsoidal E-300 D2550
-
Page 2: Table Of Contents
Contents 1. Safety Instruction ................... 2 2. Technical Specifications ................. 3 3. The Unit Construction ................6 4. Installation ..................... 6 5. Control Panel ..................7 6. Main Function ..................8 7. How to Control the Unit ............... 14 7.1 DMX Connection ................14 7.2 DMX Address Setting .............. -
Page 3: Safety Instruction
1. Safety Instruction Please read this instruction carefully which includes important information about the installation, usage and maintenance. WARNING Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. ... -
Page 4: Technical Specifications
Warning: To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. DO NOT open the unit within five minutes after switching off. The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged. ◆... - Page 5 Input Voltage: AC 100 ~240V, 50/60Hz Power Consumption: 335W Light Sources： 1 × 280W WW LED (E-300 WW) 1 × 280W CW LED (E-300 CW) CCT： 3200K ± 100K 5600K ± 150K IP Grade： IP22 ...
-
Page 7: The Unit Construction
3. The Unit Construction 1. Lens Module； 2. Framing System； 3. Bracket； 4. Main Body; 5. Clip for Gel Holder 6. Gobo Slot 4. Installation Loosen the two screws on the Main Body (MB) and put the Framing System into the MB, then turn the Framing System right .Tighten the two screws to fix the Framing System. -
Page 8: Control Panel
Put the Lens Module into the Framing System and tighten the Lens Module into the Framing System with two screws. 5. Control Panel 1．Display: To show the various menus and the selected functions. 2．Dimmer Adjust Knob：Adjust the lightness for the unit；... -
Page 9: Main Function
3．LED: MASTER Master Mode SLAVE Slave Mode DMX input present 4．MAINS OUT: PowerCon loop connection for main power supply to the next unit; 5．MAINS IN: PowerCon connection from main power supply; 6．DMX IN: For DMX512 link, use 5-pin XLR cable to link the unit and the DMX controlle 7．DMX IN: For DMX512 link, use 3-pin XLR cable to link the unit and the DMX controlle ；... - Page 10 1 ch 2D ch 2 ch...
- Page 11 DMX Address To select the DMX Address, press the ENTER button to show DMX ADDRESS on the display. Use the DOWN/UP button to adjust the address from 1 to 512. Once the address has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again.
- Page 12 Mode 1(Optically Linear): The increase in light intensity appears to be linear as DMX value is increased. Mode 2(Square Law): Light intensity control is finer at low levels and coarser at high levels. Mode 3(Inverse Square Law): Light intensity control is coarser at low levels and finger at high levels. Mode 4(S-cure): Light intensity control is finger at low levels and high levels and coarser at medium levels.
- Page 13 To select the Display Setting, press the ENTER button to confirm. Use the DOWN/UP button to select Backlight Intensity , Contrast Ratio, Backlight Auto Off, Display Inverse or Language. Backlight Intensity Select Backlight Intensity, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to adjust backlight intensity from 1 (dark) to 10 (bright), press ENTER button to store.
- Page 14 Auto Test To select the Auto Test, press the ENTER button to show AUTO TEST on the display .Use the DOWN/UP button to select the Strobe or Dimmer Value mode. To go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode.
-
Page 15: How To Control The Unit
use the DOWN/UP button to select No (keep the present setting) or Yes (the fixture will reset to factory settings and exit menu mode). To go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. -
Page 16: Dmx Address Setting
can easily distort the signal and shut down the system. 3. The DMX output and input connectors are pass-through to maintain the DMX circuit, when one of the units’ power is disconnected. 4. Each lighting unit needs to have a DMX address to receive the data by the controller. The address number is between 0-511 (usually 0 &... -
Page 17: Dmx Configuration
7.3 DMX Configuration 1 Channel Mode： CHANNEL VALUE FUNCTION DIMMER 0 – 255 Close Open（0% ~ 100%） 2D Channel Mode： CHANNEL VALUE FUNCTION DIMMER 0 – 255 Close Open（0% ~ 100%） DIMMER FINE 0 – 255 Close Open（0% ~ 100%） 2 Channel Mode：... -
Page 18: Troubleshooting
190 – 231 Strobe：Fast Open Slow Close，Slow Fast 232 – 239 Open 240 – 247 Random Strobe 248 – 255 Full On 8. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. -
Page 19: Fixture Cleaning
9. Fixture Cleaning The cleaning of external must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics. ... - Page 20 Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55103-1: 2009 ; EN55103-2: 2009; EN62471: 2008; EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008. &...