Rath 2100-CPL Installation & Operation Manual
36” emergency call station
Hide thumbs
Also See for 2100-CPL:
- Installation & operation manual (9 pages) ,
- Installation & operation manual (8 pages)
Table of Contents
Advertisement
Quick Links
Installation & Operations Manual
36" Emergency Call Station
36" Emergency Call Station
• 2100-CPL Landline 120v Call Station
• 2100-CPC Cellular 120v Call Station
• 2100-CPV VoIP 120v Call Station
• 2100-CPW Wi-Fi VoIP 120v Call Station
N56W24720 N. Corporate Circle
Sussex, WI 53089
RP8500CP
Made in the USA
Ver. 6
800-451-1460
www.rathcommunications.com
2 Year Warranty
04/21
Advertisement
Table of Contents
Related Manuals for Rath 2100-CPL
Summary of Contents for Rath 2100-CPL
- Page 1 Installation & Operations Manual 36” Emergency Call Station 36” Emergency Call Station • 2100-CPL Landline 120v Call Station • 2100-CPC Cellular 120v Call Station • 2100-CPV VoIP 120v Call Station • 2100-CPW Wi-Fi VoIP 120v Call Station N56W24720 N. Corporate Circle...
-
Page 2: Table Of Contents
Thank you for purchasing RATH’s Low Voltage Call Station. We are the largest Emergency Communication Manufacturer in North America and have been in business for over 35 years. We take great pride in our products, service, and support. Our Emergency Products are of the highest quality. -
Page 3: Description
Description Features: Figure 1: Front & Back View • ADA compliant (hands free operation) • LED call status indicator 8” 10” 1-9/16” • Powder coated aluminum construction 3” • NEMA 4 enclosure for electronics • Conduit holes for easy installation •... -
Page 4: Items Needed
Wall Mounting Hardware If Mounting to Wall Pole Mount Bracket (Part # RP7700098A) If Mounting to Pole #1 Phillips Screwdriver Voltage Meter Security Torx Bit Provided by RATH ® Adjustable Wrench 120v Power Source Analog Phone Line If Using Landline Phone Cable... - Page 5 LTE Cellular (Units Are Carrier Specific): 1. Open the Cellular Gateway by unscrewing the screw on the left side of the front cover with a Phillips screwdriver and gently pull up on the left side. 2. Insert standard size SIM card (25mm x 15mm) into J4 with the perforated edge first and the gold contact side facing downward.
-
Page 6: Phone Programming
Phone Programming 1. You can program the phone on-site or remotely. Note: Cellular applications cannot be remotely programmed. 2. If programming on-site, remove 12 security screws from unit, remove top cap, and pull front assembly away from back unit. 3. Remove the cover of the NEMA 4 enclosure by loosening the 4 corner screws. On-Site Programming: Step 1: To Begin Program Mode A. -
Page 7: Phone Testing
If you have answered YES to all questions, you have successfully installed and tested the phone. If you answer NO to any question, proceed to the Troubleshooting Section. *RATH recommends the Call Station be tested on a regular basis to ensure proper operation. -
Page 8: Troubleshooting
Troubleshooting Problem Possible Cause & Solutions No dial tone when the button is • Check to make sure the phone line is connected to SmartPhone board. pushed: • Verify dial tone and voltage on phone line going into unit. Audio is low from the speaker: •... -
Page 9: Wiring
Wiring Strobe FRONT COVER Strobe Constant Communication Phone line to 900 MHz, Radio, or Cellular Source LED for Panel Enter Note: If using landline, phone cable Record will just run out of the bottom of the Play / Pause NEMA 4 enclousre Stop LN G Wago Connector...