Table of Contents
Advertisement
Quick Links
Vision™ OPLC™
This guide provides basic information for Unitronics' controllers V570-57-C30B and V570-57-T40B.
General Description
Vision OPLCs are programmable logic controllers that comprise an integral operating panel.
V570-57-C30B and V570-57-T40B comprise a color touchscreen, which displays a virtual keyboard
when the application requires the operator to enter data.
Communications
I/O Options
Information
Mode
Programming
Software,
& Utilities
1 Number of I/Os may vary according to I/O module selection.
Unitronics
2 isolated RS232/RS485 ports
Isolated CANbus port, CANopen & UniCAN
The user can order and install an Ethernet port
Communication Function Blocks include: SMS, GPRS, MODBUS serial/IP
Protocol FB enables PLC to communicate with almost any external device,
via serial or Ethernet communications
Vision supports up to 512
high-speed, and analog I/Os via:
Snap-in I/O Modules
Plug into the back of the
controller to provide an on-
board I/O configuration
I/O Expansion Modules
Via adaptor, local or remote I/Os
may be added via expansion port
or CANbus
Installation instructions and other data may be found in the module's technical
specification sheet.
This mode enables you to:
Calibrate the touchscreen
View & Edit operand values, COM port settings, RTC and screen
contrast/brightness settings
Stop, initialize, and reset the PLC
To enter Information Mode, press the touchscreen and maintain contact for
several seconds.
The Unitronics Setup CD contains VisiLogic software and other utilities
VisiLogic
Easily configure hardware and write both HMI and Ladder control
applications; the Function Block library simplifies complex tasks such
as PID. Write your application, and then download it to the controller
via the programming cable included in the kit.
Utilities
These include UniOPC server, Remote Access for remote
programming and diagnostics, and DataXport for run-time data
logging.
To learn how to use and program the controller, as well as use utilities such as
Remote Access, refer to the VisiLogic Help system.
Installation Guide
V570-57-C30B and V570-57-T40B (Color)
1
digital,
1
Advertisement
Table of Contents
Related Manuals for Unitronics Vision OPLC V570-57-C30B
Summary of Contents for Unitronics Vision OPLC V570-57-C30B
- Page 1 Vision™ OPLC™ Installation Guide V570-57-C30B and V570-57-T40B (Color) This guide provides basic information for Unitronics’ controllers V570-57-C30B and V570-57-T40B. General Description Vision OPLCs are programmable logic controllers that comprise an integral operating panel. V570-57-C30B and V570-57-T40B comprise a color touchscreen, which displays a virtual keyboard when the application requires the operator to enter data.
-
Page 2: Danger Symbols
All examples and diagrams are intended to aid understanding, and do not guarantee operation. Unitronics accepts no responsibility for actual use of this product based on these examples. Please dispose of this product according to local and national standards and regulations. -
Page 3: Inserting The Battery
1. Remove the battery cover shown on page 6. The polarity (+) is marked on the battery holder and on the battery. 2. Insert the battery, ensuring that the polarity symbol on the battery is: - facing up - aligned with the symbol on the holder 3. Replace the battery cover. Dimensions Unitronics... - Page 4 4. Tighten the bracket screws against the panel. Hold the bracket securely against the unit while tightening the screw. 5. When properly mounted, the controller is squarely situated in the panel cut-out as shown below. Unitronics...
-
Page 5: Wiring: General
Earthing the controller’s power supply: connect one end of a 14 AWG wire to the chassis signal; connect the other end to the panel. Note: The wire used to earth the power supply must not exceed 10 cm in length. If your conditions do not permit this, do not earth the power supply Unitronics... -
Page 6: Communication Ports
RS232/RS485: DIP Switch Settings The settings below are for each COM port. Switch Settings RS232* RS485 RS485 with termination** *Default factory setting **Causes the unit to function as an end unit in an RS485 network Unitronics... - Page 7 1. Line the circular guidelines on the controller up with the guidelines on the Snap-in I/O Module as shown below. 2 Apply even pressure on all 4 corners until you hear a distinct ‘click’. The module is now installed. Check that all sides and corners are correctly aligned. Unitronics...
- Page 8 CAN protocols: Circuit protection CANopen: 127 controllers or external device devices Unitronics’ proprietary UniCAN: 60 terminating controllers, (512 data bytes per scan) resistor The CANbus port is galvanically isolated. CANbus Wiring Use twisted-pair cable. DeviceNet® thick shielded twisted pair cable is recommended.