Table of Contents
Advertisement
S
S
S
UPER
TORAGE
YSTEM 2028R-E1CR24L User's Manual
5-7
Serverboard Details
Figure 5-5. X10DRH-iT Layout
BMC
LAN CTRL
JIPMB1
BAR CODE
Battery
MAC CODE
BIOS
BIOS
LICENSE
PCH
LEDS6
LEDS5
JBT1
LSI 3108
SAS0-3
SAS4-7
SAS CTRL
JS39
SP1
FANA
JSTBY1
JD1
JOH1
Notes
Jumpers not indicated are for test purposes only.
Note that the PCI slots are enabled when their corresponding processors are in-
stalled. "CPU2 Slot 4" indicates that a second CPU must be installed in the CPU2
socket to enable this PCI slot.
" " indicates the position of pin 1.
The LSI 3108 onboard controller chip in the layout image above is not populated
on the X10DRH-iT.
The 2028R-E1CR24L comes pre-installed with a Hardware RAID controller installed
in PCI-E slot 2 and a JBOD expansion port installed in PCI-E slot 1.
LAN2
LAN1
UID
USB0/1
VGA
COM1
FAN6
USB4/5
(3.0)
FAN5
CPU2
CLOSE 1st
OPEN 1st
X10DRH-C/i(T)
Rev. 1.00
CPU1
CLOSE 1st
OPEN 1st
JF1
5-12
X10DRH-iT Quick Reference
Jumper
Description
JBT1
Clear CMOS/Reset BIOS Configuration
JI
C1/JI
C2 SMB to PCI-E Slots
2
2
JPB1
BMC Enable/Disable
JPG1
VGA Enable/Disable
JPL1
TLAN1/TLAN2 Enable/Disable
JPME2
Manufacture (ME) Mode Select
JWD1
Watch Dog Timer
Connector
Description
COM1/COM2
Backplane COM Port1/Front accessible COM2 header
FAN1-6,A, B
Fan Headers
J24
24-pin ATX Main Power Connector
JD1
Speaker/Power LED Header
JF1
Front Control Panel Header
JIPMB1
4-pin External BMC I
JL1
Chassis Intrusion Header
JPI
C1
Power Supply SMBbus I
2
JPWR1/JPWR2
12V 8-pin Power Connectors
JSTBY1
Standby Power Connector
JTPM1
TPM (Trusted Platform Module)/Port 80 Header
LAN1/LAN2
10G-bit Ethernet (TLAN) Ports
IPMI_LAN
Dedicated IPMI LAN (supported by the ASpeed controller)
I-SATA 0-5
SATA 3.0 Ports (supported by Intel PCH)
S-SATA
SATA 3.0 4-port Vertical Connector (supported by Intel SCU)
(I-)SGPIO1/2
Serial Link General Purpose I/O Headers
UID
UID (Unit Identification) Button
USB 0/1 (2.0)
USB 2.0 Ports (rear I/O)
USB 2/3 (2.0)
USB 2.0 Headers
USB 4/5 (3.0)
USB 3.0 Ports (rear I/O)
USB 7/8 (3.0)
USB 3.0 Header
USB 6 (3.0)
Type A USB 3.0 Connector
LED
Description
LE1
Rear UID LED
LE2
Onboard PWR LED
LEDM1
BMC Heartbeat LED
5-13
Chapter 5: Advanced Serverboard Setup
Default Setting
See Section 5-9
Pins 2-3 (Disabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Normal)
Pins 1-2 (Reset)
C Header (for an IPMI card)
2
C Header
2
State
Status
Blue: On
Unit Identified
On
Power On
Green: Blinking
BMC Normal
Advertisement
Table of Contents
