Appendix; General Operation Troubleshooting; Administration Troubleshooting; Ap Windows Client Troubleshooting - Tripp Lite B064-016-02-IP Owner's Manual

Appendix

General Operation Troubleshooting

Problem
Erratic Operation
I can't access the B064-Series KVM
Switch, even though I have specified the
IP address and port number correctly.
Mouse and/or Keyboard not responding.
Sudden loss of network connection.
No video display on the remote console.
When logging in from a browser, the
following message appears: 404
Object Not Found.
When I log in, the browser generates a
CA Root certificate is not trusted, or a
Certificate Error response.
There are two mouse pointers after the
remote system is accessed.
The display on the remote console is
distorted and performing an Autosync
doesn't resolve the problem.
I can log in with my Username and
Password from a remote location, but
cannot log in from the Local Console.

Administration Troubleshooting

Problem
After upgrading the firmware and
logging back in, the B064-Series KVM
Switch appears to still be using the old
firmware version.

AP Windows Client Troubleshooting

Problem
Windows Client won't connect to the
B064-Series KVM Switch.
Remote mouse pointer is out of sync.
Part of remote window is off my monitor.
The remote screen is rotated 90 degrees.
I cannot run Net Meeting when the
Windows Client is running.
Action
Reset the unit by pressing and holding the Reset button on the front of the unit for longer than three
seconds.
If the B064-Series KVM Switch is behind a router, the router's Port Forwarding (also referred to as
Virtual Server) feature must be configured.
• If accessing the KVM via local console, unplug and replug the cable(s) from the console port(s).
• Turn the connected computer/server off and then back on. All connected devices need to be powered
off when connecting to the KVM.
Close your B064-Series KVM Switch connection. Wait approximately 30 seconds, and log in again.
• Make sure the resolution of the monitor being used to display the remote computer/server is higher
than that of the remote computer/server.
• Make sure the OSD toolbar is closed. Sometimes mouse movement is required to bring the screen out
of sleep mode. If the OSD toolbar is open, your mouse input is not being received by the remote
computer/server.
If a login string has been set, make sure to include the forward slash and correct login string when you
specify the B064-Series KVM Switch IP address.
The certificate can be trusted. (See Trusted Certificates page 15 for details)
The KVM automatically defaults to show both the local and remote mouse pointers. You can choose to
display both mouse pointers at the same time or only the remote mouse pointer. (See Mouse Pointer
Type on page 23 for details.)
• Switch ports to a port with a different resolution and then switch back.
• Lower the resolution and refresh rate for the computer/server connected to the port.
The Local Console only supports logins for usernames and passwords that contain the following
characters: A – Z, 0 – 9, and Space. If your Username or Password contains characters other than
these, you will not be able to log in from the Local Console.
Action
Clear your browser's cache. Delete all temporary internet files and cookies. Close the browser and
reopen it to log in with a new session.
Action
DirectX 7.0 or higher must be installed on your computer.
• Perform a Video Auto Sync. (See Video Settings on pages 20-21 for details) This will most often sync
the local and remote mouse pointers.
• Use the Adjust Mouse Hotkey command. (See Adjust mouse on page 19 for details)
• If this does not work, see Manual Mouse Synchronization on page 23.
• If Keep Screen Size is not enabled (see Screen Options on page 19), try performing a Video Auto
Sync (see Video Settings on pages 20-21) to sync the local and remote monitors. If this does not work,
you may have to manually adjust the Screen Position in the Video Settings screen.
• If Keep Screen Size is enabled, areas that are off the screen can be accessed by positioning the
mouse pointer on the far side of the area you want to scroll to.
Enable Keep Screen Size. (See Control Panel Configuration on page 19)
Enable Keep Screen Size. (See Control Panel Configuration on page 19)
68