Ness D16 XCEL 4G User Manual
Hide thumbs
Also See for D16 XCEL 4G:
- Installation & programming manual (96 pages) ,
- User manual (28 pages) ,
- Owner's manual (24 pages)
Subscribe to Our Youtube Channel
Related Manuals for Ness D16 XCEL 4G
Summary of Contents for Ness D16 XCEL 4G
- Page 1 USER'S ManUaL ness SIM information, see page 36. D8XCEL & D16XCEL 4G panels with Document 890-497 1.11 KPX+ & Saturn+ LCD Keypads...
- Page 2 improvement.
-
Page 3: Table Of Contents
ContEntS features ......................4 operation ....................... 5 Keypads overview ..................6 Keypad Display in operating Mode ..............7 Keypad Beeps / Keypad Settings ..............8 oPERatIon arming ....................... 10 Disarming....................11 home Mode ....................12 Keypad Panic ..................... 13 Keypad Duress ..................13 Keypad fire alarm .................. -
Page 4: Features
• 3 Door Access Controller onboard with support for Weigand prox or fingerprint readers. • Control via internet using Ness iComms/aComms iOS and Android apps and optional ethernet adapter. • Voice alarm reports & Voice prompts for remote telephone operation. -
Page 5: Operation
See page 10. Mode. Any zone may be allocated to any area. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 6: Keypads Overview
KEyPaDS oVERVIEW the instructions in this manual relate to ness KPX+ and Saturn+ keypads. the KPX keypad is used in examples throughout this manual. Saturn keypad operation is identical. Refer to the ness navigator user's manual for operating instructions specific to the navigator touch Screen keypad. -
Page 7: Keypad Display In Operating Mode
'offline' without a SIM card. See page 16 for keypad indicators in Memory Mode. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 8: Keypad Beeps / Keypad Settings
LCD during adjustment. on the LCD during adjustment. mode or program mode. See Keypad Chime, page 17. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... - Page 9 Radio Interface (100-200) to be fitted support. Emergency alarms must be enabled in the control panel to be to the control panel.
-
Page 10: Operation Arming
If a zone is Unsealed at the end of exit time and the auto-exclude option is disabled, the siren will sound for the duration of siren time, (default is 5 minutes). Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 11: Disarming
If Entry Beeps are enabled. Memory Mode. In the event of an alarm, the strobe light will flash for 72 hours or until the panel is reset. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 12: Home Mode
(RK4 radio key note: home Mode arming when area2 is armed only). these options must be enabled by your cannot be done by Radio Key or by keyswitch. installer. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 13: Keypad Panic
User Code with one of the digits 5, 6, 8 or * THE DURESS ALARM CAN BE PROGRAMMED TO 9 when Disarming. SoUnD thE IntERnaL SIREn (RESEt oUtPUt). thIS oPtIon IS off By DEfaULt. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 14: Keypad Fire Alarm
SMS (if the option is enabled and monitoring is enabled and you have an active SIM card). Clear the alarm by entering a valid user code + E Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 15: Excluding Zones
E works only when the panel is Disarmed. • EXCLUDE [UserCode] E works in any state. Note that this method can only exclude the zones in the Area assigned to that code. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 16: View Memory
Radio Device tamper alarm (Device number is indicated by zone lights) RaDIo, hoME, ZonE Radio Supervision alarm (Device number is indicated by zone lights) hoME, ZonE Wired Zone Supervision alarm (Zone number is indicated by zone lights) Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 17: Temporary Day Zones
2 seconds. When Day Mode is disabled, an unsealed day zone will simply be indicated on the keypad as an unsealed zone. the hoME icon flashes continuously when temporary Day Mode is enabled. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 18: Autotime Features
- then your panel may have been programmed for autotime events. ask your install to check the installer-level programming settings and reprogram the system to suit your needs. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 19: Autotime Operation
(or off) of one of the aUX outputs in the same manner. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 20: Aux Outputs
2. Program a new user code, eg. P210E user code 10 = 9876 3. Remove user code 10 from area 1 4. to operate aux1 by SMS, send 9876E11on or 9876E11off Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 21: Sms Operation
If the valid user code is not the master user only when the command allows it. code, but the command requires the master code then the reply is “wrong message” Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 22: Summary Of Sms Commands
MEDICaL alarm triggers the strobe light if programmed and sends a medical report if programmed. the PanIC alarm triggers the sirens and strobe if programmed. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 23: Sms Text Output
Using the same method every word and phrase in the SMS message can be renamed. Refer to the text table on page 24 Refer to the Installation Manual for further detail. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... - Page 24 DooR 3 (D3) USER 17 (U17) USER 18 (U18) *Shortcut names are provided for simplified ... to User 56 (U56) programming by SMS. (omit the brackets). See page 23 Changing text output Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL...
-
Page 25: Programming
28. the factory default Master Code is 123. you should re-program this code with a new code of your own choice. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 26: Programming By Sms
Master code. eXample 2 Program User Code 2 to be 5678. SMS SEnt to thE PanEL SMS REPLy M123E aCK P123E P202E 5678E 5678E M202E aCK 5678E aCK 5678E aCK ME aCK Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 27: Programming Options Table
2. the panel will respond to a valid command from any mobile phone number, not just the numbers programmed. however, “Unknown” phone numbers will not get replies to invalid messages. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 28: User Code Programming
3. When re-programming a Keypad Code, the old code does not need to be deleted first. the new code will overwrite the old code. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 29: Entry/Exit Timer Programming
D8XCEL & D16XCEL supports up to 3 user-programmable phone numbers for SMS reporting of alarm events and 2 phone numbers for open/close reports by SMS messaging. See page 27 for program option numbers. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 30: Real Time Clock Programming
'offline' without a SIM card If the clock is manually set you will need to adjust the hours setting for Daylight Savings. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 31: Monitoring, Central Station / Sms Self Monitoring
CEntRaL StatIon MonItoRInG ness XCEL control panels have an on-board cellular communicator which can send detailed alarm messages to a Central Monitoring Station via IP protocols. The digital messages can include information about the zone or zones which caused the alarm, tamper alarms, low battery or mains failure reports, and it can also (by user number) identify the users who arm and disarm the system. - Page 32 Z3 RUMPUS aREa 1 tue 7 aug 2018 4:07:22pm 1/1 SMS MESSaGE EXPLaInER nESS security report Identifies the message as a ness alarm panel report. MyPanEL identifies the premises. this ID can be programmed by SMS using the LoCatIon command. See page 23.
-
Page 33: Troubleshooting
... or displays noSC ... a valid SIM card is not fitted. fit a valid SIM card. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 34: Operation Summary
[SelectZones] KPX/SatURn naVIGatoR then press E to exit Exclude mode or press to exit. The Exclude icon flashes constantly while zones are excluded. Excluded zones are automatically included on disarming. Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 35: Installation Record
P228E P247E P210E P229E P248E P211E P230E P249E P212E P231E P250E P213E P232E P251E P214E P233E P252E P215E P234E P253E P216E P235E P254E P217E P236E P255E P218E P237E P256E P219E P238E Ness D8xCeL / D16xCeL CoNtroL PaNeL – User's MaNUaL... -
Page 36: Sim Activation Information
SIM. a ness SIM card is supplied for your convenience. you can choose to activate the ness SIM or Byo SIM on a network of your choice. Please activate the ness SIM to enjoy the advantages of remote access and monitoring via the cellular network.
Need help?
Do you have a question about the D16 XCEL 4G and is the answer not in the manual?
Questions and answers
What code do i enter to turn off alarm via SMS on Ness D16 4G
To turn off (disarm) the alarm via SMS on the Ness D16 XCEL 4G, send an SMS command to the panel using the appropriate format. The SMS command should be:
P[MasterCode]D
Replace [MasterCode] with your actual master code. This command disarms the alarm system remotely via SMS.
This answer is automatically generated