Subscribe to Our Youtube Channel
Related Manuals for Ness D8X DELUXE
Summary of Contents for Ness D8X DELUXE
- Page 1 D8x/D16x Deluxe User's ManUal Hardware & Firmware v8.x Document 890-016 for KPX & saturn lCD Keypads refer to document 890-402 navigator Manual for operation by ness navigator Touch screen keypad...
- Page 2 improvement.
-
Page 3: Table Of Contents
Telephone number programming ......23 real Time Clock programming ......24 Monitoring, Central station / audible ......25 remote operation by telephone ......26, 27 ness accessories ..........28, 29 Troubleshooting ............30 Installation record ............. 31 oPeraTIon sUMMary ..........32... -
Page 4: Features
• 3 Door Access Controller onboard with support for Weigand prox or fingerprint readers. • Control via internet using Ness iComms/aComms iOS and Android apps and optional ethernet adapter. • Voice alarm reports & Voice prompts for remote telephone operation. -
Page 5: Introduction
Cards/Fobs can reset the panel if during this allowed time. the D option has been isArm ccess enabled by your installer. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 6: Keypad
2 seconds. all the icons will be on while the button is held down. Display Test can be activated at any time either in operating mode or any program mode. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 7: Visual Indicators
User Program Mode. Installer Program Mode. PROG normal Dialler is on line. Phone line fault or LINE failure to communicate. see page 16 for keypad indicators in Memory Mode. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 8: Operation
24hr and Home zones are independent of the separate systems sharing only the siren outputs area operations. and dialler. note: area partitioning is in addition to Home Mode. Any zone may be allocated to any area. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... - Page 9 Keys and access cards and readers are optional and are not supplied with any ness control panel as standard. ness radio products require a ness radio Interface (100-200) to be fitted to the control panel.
-
Page 10: Arming
Mains Power is turned off or the backup battery is low. one long beep when you arm could mean the panel is already armed or the keypad code is wrong, (if not using shortcut arming). ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 11: Disarming
(if installed), reset the panel as 72 hours or until the panel is reset. above. To check the cause of the alarm, you can view the alarms in memory by entering Memory Mode. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 12: Home (Monitor) Mode
(rK4 radio key note: Home Mode arming when area2 is armed only). These options must be enabled by your cannot be done by radio Key or by keyswitch. installer. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 13: Keypad Panic
User Code with one of the digits 5, 6, 8 or * THe DUress alarM Can Be PrograMMeD To 9 when Disarming. soUnD THe InTernal sIren (reseT oUTPUT). THIs oPTIon Is oFF By DeFaUlT. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 14: Keypad Fire Alarm
(If Keypad Fire Alarm has been enabled by your installer). and sends a Fire alarm report by dialler. (If this option has been enabled by your installer and the system is monitored by a central station). ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 15: Excluding Zones
• EXCLUDE E works only when the panel is Disarmed. • EXCLUDE [User Code] E works in any state. • EXCLUDE [User Code] E can only exclude the zones in the Area assigned to that code. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 16: View Memory
Radio Device tamper alarm (Device number is indicated by zone lights) raDIo, HoMe, Zone Radio Supervision alarm (Device number is indicated by zone lights) HoMe, Zone Wired Zone Supervision alarm (Zone number is indicated by zone lights) ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 17: Temporary Day Zones
2 seconds. When Day Mode is disabled, an unsealed day zone will simply be indicated on the keypad as an unsealed zone. The MonITor icon flashes continuously when Temporary Day Mode is enabled. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 18: Autotime Features
- then your panel may have been programmed for autoTime events. ask your install to check the installer-level programming settings and reprogram the system to suit your needs. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 19: Autotime Operation
(and back on again) any time you wish. at the scheduled turn oFF time, if the output is still on it will be turned off. Whether an output "Pulses" or "Turns on" depends on the how that output has been programmed by your installer. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 20: Programming
Follow Me number is ignored. The factory default Master Code is 123. you For all other programming changes, talk to should re-program this code with a new code your installer. of your own choice. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 21: Programming Options Table
Delay Time 2 6 (60 sec) This option works in multiples of 10. (6 = 60 sec). P28e exit Delay Time 60 (60 sec) P00e Follow Me Phone no. blank ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 22: User Code Programming
3. When re-programming a Keypad Code, the old code does not need to be deleted first. The new code will overwrite the old code. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 23: Entry/Exit Timer Programming
The Follow Me telephone number is only used in audible Dialling mode. If the Follow Me number is programmed, then the primary & secondary numbers are ignored. ask your installer for further information. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 24: Real Time Clock Programming
Hours setting when Daylight savings starts and ends. Clock memory is retained on power down. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 25: Monitoring, Central Station / Audible
HasH and then hang up the phone. Press sTar then HasH to hang up. Press 2 then 2 to continue to the telephone remote control menu. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 26: Remote Operation By Telephone
To arm, Press 1. To disarm, Press 2. To return, Press sTar. The user presses 1 to arm and the voice prompt continues with either of these messages: ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... - Page 27 3. To listen to reports press 4. To hang up press sTar then press HasH. The user presses sTar then HasH (* then #) to hangup. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal...
-
Page 28: Ness Accessories
DVrs are available in 4, 8 or 16 channel models in The Ness Quantum™ Pet Aware PIR and Pet Aware standard definition or full 1080p HD for high definition Dual have a superior ability to discriminate between surveillance and recording. - Page 29 Panic alarm. Keys™ provide the benefits of separate ON, OFF and The ness radio Keypad is suitable for use as a portable PanIC buttons as well as optional control of auxiliary keypad or for adding an extra keypad in areas where it outputs - all in a slim, waterproof remote control.
-
Page 30: Troubleshooting
The panel re-arms itself a auto re-arm is enabled. enter the premises after disarming. short time after disarming. auto re-arm is designed to re-arm the panel if you don't enter the premises after disarming. ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 31: Installation Record
P230E P249E P212E P231E P250E P213E P232E P251E P214E P233E P252E P215E P234E P253E P216E P235E P254E P217E P236E P255E P218E P237E P256E P219E P238E © 2004 Ness Security Products ness D8X / D16X DelUXe ConTrol Panel – User's ManUal... -
Page 32: Operation Summary
KeyPad oPeration Summary operation by KeyPaD to arM Press The panel must initially be (If the arming shortcut is enabled) disarmed. or press + [u or press [u (If Code only arming has been enabled for that user code) to DIsarM Press [u To disarm and/or reset alarms.
Need help?
Do you have a question about the D8X DELUXE and is the answer not in the manual?
Questions and answers