Table of Contents
Advertisement
The cooking time has elapsed
A signal sounds. The oven stops heating. The status bar shows
the cooking time as
0:00. You can cancel the signal early
x
by pressing the
button.
0
Cancelling the cooking time
Press the
button to open the menu. Move to the cooking
0
time using the
or
button and set the cooking time to 0:00
¿
¾
with the rotary selector. The type of heating and temperature
set are shown in the display. Press the
continues without a set cooking time.
Changing the cooking time
Press the
0
button to open the menu. Using the
button, move to the cooking time and set the cooking time
using the rotary selector. Press the
menu.
Setting a later end time
Please remember that easily spoiled foods must not be allowed
to remain in the cooking compartment for too long.
A later end time can be set for
all types of heating
■
a variety of programmes
■
and for self-cleaning
■
Example: you put the dish in the cooking compartment at 9.30 .
It takes 45 minutes to cook and will be ready at 10.15, but you
would like it to be ready at 12.45 instead.
Change the end time from 10.15 to 12.45. The oven goes into
standby. Cooking starts at 12.00 and finishes at 12.45.
This function is also available for self-cleaning. You can shift the
time of the cleaning operation so it is carried out at night, which
means that the oven is available at all times during the day.
Setting a later end time
Prerequisite: The selected operation has not already begun and
a cooking time has already been set. The time-setting options
menu
0
is open.
Move to the end time using the
1.
displayed.
7\SHV RI KHDWLQJ
&RRNLQJ WLPH
PLQ VHF
Using the rotary selector, set a later end time.
2.
7\SHV RI KHDWLQJ
&RRNLQJ WLPH
PLQ VHF
Childproof lock
The oven has a childproof lock to prevent children switching it
on accidentally.
The oven will not react to any settings. The timer and clock can
also be set when the childproof lock has been switched on.
10
button, operation
†
¿
or
¾
0
button to close the
button. The end time is
¿
(QG
(QG
Press the
0
button to close the time-setting options menu.
3.
Confirm by pressing the
4.
The setting is adopted. The oven is in standby, the
is displayed in the status bar. Operation starts at the
appropriate time. You can see the
down in the status bar.
The cooking time has elapsed
A signal sounds. The oven stops heating. The status bar shows
the cooking time as
0:00. You can cancel the signal early
x
by pressing the
0
button.
Correcting the end time
This is possible, providing the oven is on standby. To do this,
open the menu with the
0
the
¿
or
¾
button and adjust the end time using the rotary
selector. Press the
0
button to close the menu.
Cancelling the end time
This is possible, providing the oven is on standby. To do this,
open the menu with the
0
the
or
button and turn the rotary selector anti-clockwise
¿
¾
until the display disappears. The cooking time immediately
starts to count down.
Setting the clock
The oven must be switched off before you can set or change
the clock.
Following a power cut
"Set clock" appears in the status bar following a power cut.
Turn the rotary selector to set the current time.
1.
The display language set is displayed in the settings area on
the right-hand side. This does not change following a power
cut.
Press the
button.
0
2.
The time is applied.
Changing the clock
Example: changing from summer to winter time.
Press the
button.
0
1.
The time-setting options menu appears.
Use the
button to move to the
¿
2.
time using the rotary selector.
Press the
button.
0
3.
The time-setting options menu closes.
Changing the clock display
The clock appears in the display when the oven is switched off
and shows the current time. You can change the display to a
different clock appearance, to digital time or remove the clock
from the display. For more information, refer to the Basic
settings section.
Activating the childproof lock
Press and hold the
button until the
@
This takes about 4 seconds.
The control panel is locked.
†
button.
y
z
cooking time counting
button, move to the end time with
button, move to the end time using
clock, then change the
0
symbol appears.
@
end time
Advertisement
Table of Contents
