Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HGLRC FD413 Stack
Summary of Contents for HGLRC FD413 Stack
- Page 1 FD413 STACK Manual www.hglrc.com...
-
Page 2: Table Of Contents
Select ESC telemetry..........................8 Voltage parameters setting........................9 Setting up the receiver..........................10 VTX serial port use. VTX uses OSD smart audio................11 Check receiver signal..........................13 Select flight mode startup mode......................14 OSD settings..............................15 LED settings..............................16 Troubleshooting............................17 ..................Package IncIuded FD413 STACK*1 Accessory Bag*1 www.hglrc.com... -
Page 3: Product Specifications
1.Product Specifications Product parameters Model FD413 STACK Weight Usage for 65mm-120mm Frame Kit Flight Controller FDF411 FD13A 4in1 FD VTX Micro Firmware Betaflight HGLRC411 Support receiver SBUS .PPM..DSMX.i.BUS Input Voltage 2-4S Lipo 21X21mm Size 16*16mm mounting holes（M2） www.hglrc.com... -
Page 4: Interface Description
2.Interface Description 3.Check the flight control drive 1. Long Press BOOT buttons.connect USB.The system automatically install the driver www.hglrc.com... - Page 5 2.Driver cannot be installed, please download ImpulseRC_Driver_Fixer 3.Double-click on the run(Plug in the flight controller to automatically install the driver) 4.open betaflight configurator enter DFU mode ， Load firmware Waiting for 5.Click Select firmware version（HGLRCF411） completion 6.Click It will be prompted upon completion www.hglrc.com...
-
Page 6: Calibration Accelerometer
7.open betaflight configurator 。Controller plugged into the computer. Betaflight Automatically assigned port，click “Connect” Enter setup interface（Different computer COM） 4. Calibration accelerometer 1. Put the aircraft horizontal and click“Reset Z axis” Click again www.hglrc.com... -
Page 7: Urat Serial Port Use
5.URAT serial port use URAT1 uses VTX image transmission UART2 uses receiver telemetry 6.Select aircraft model Select model Click www.hglrc.com... -
Page 8: Choose Esc Protocol
I understand the risks 2.Click Click Push Master to check motor “ ” steering Master Steering can be changed at BLHeliSuite “ ” 7.Choose ESC protocol 1.Choose the right ESC protocol, the optional universal protocol DSHOT600. www.hglrc.com... -
Page 9: Voltage Parameters Setting
8.Voltage parameters setting 1.Click Setting parameters www.hglrc.com... -
Page 10: Setting Up The Receiver
9.Setting up the receiver 1.Receiver connection diagram 2.Click have found UART2 Open （SBUS） the receiver serial port “ ” www.hglrc.com... - Page 11 3.Open (i.BUS/DSMX) receiver serial port 4.Set the SBUS receiver 5.Set the i.BUS receiver 6.Set the DSMX receiver 7. .Set the receiver www.hglrc.com...
-
Page 12: Vtx Serial Port Use. Vtx Uses Osd Smart Audio
10.VTX serial port use. VTX uses OSD smart audio 1.VTX connection diagram www.hglrc.com... - Page 13 Roll-right will enter the sub-menu. For example, in the screen to the right, moving the cursor to “Features” and then moving the roll stick to the right will enter the “Features” sub-menu. www.hglrc.com...
- Page 14 The screen to the right shows the current vTX settings. From here, you can change the frequency band, channel, and power level of the video transmitter. After making the changes, move the cursor to “Set” and press roll-right to confirm the settings. www.hglrc.com...
-
Page 15: Check Receiver Signal
11.Check receiver signal Check the remote control output signal 1.Click 12.Select flight mode startup mode set up the function of remote control switch across the Click channel (below are for reference only) www.hglrc.com... -
Page 16: Osd Settings
13.OSD settings the OSD Settings, according to the need to choose, drag Click the OSD schematic diagram of the parameters can be adjusted. www.hglrc.com... -
Page 17: Led Settings
14.LED settings Click Turn on LED support 2.Click Click set according to need www.hglrc.com... -
Page 18: Troubleshooting
2. If the product is damaged due to improper operation, the repair service may be provided under the condition that the inspection can be repaired. 3. For domestic customers, please contact the after-sales service personnel. For overseas customers, please contact the official website for after-sales service. www.hglrc.com... - Page 19 "BBB" sound. There is only one sound. Please check if the ESC agreement is correct 3.The spin of the aircraft keeps spinning 1. Please check if the propeller is correct 2. Please check if the motor direction is correct www.hglrc.com...
Need help?
Do you have a question about the FD413 Stack and is the answer not in the manual?
Questions and answers