Table of Contents
Advertisement
Quick Links
TURBO HD
H1T Series Dome Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type
Type I
Camera
Type II
Camera
This manual may contain technical incorrect places or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or
update the products or procedures described in the
manual.
DS-2CE56H1T-(A)VPIT3Z(E)
DS-2CE56H1T-(A)ITZ(E)
Model
0300001070703
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CE56H1T-VPIT3Z
Summary of Contents for HIKVISION DS-2CE56H1T-VPIT3Z
- Page 1 TURBO HD H1T Series Dome Camera User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type Model Type I DS-2CE56H1T-(A)VPIT3Z(E) Camera Type II...
-
Page 2: Regulatory Information
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
- Page 4 Keep the camera away from liquid while in use for non-water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark Description DC Voltage AC Voltage...
-
Page 5: Installation
1 Introduction 1.1 Product Features The camera is applicable for both indoor and outdoor conditions, and the application scenarios include road, warehouse, underground parking lot, bar, etc.. The main features are as follows: High performance CMOS sensor Low illumination, 0.01 Lux@(F1.2, AGC ON), 0 Lux ... - Page 6 Check the specification of the products for the installation environment. Check whether the power supply is matched with your power output to avoid the damage. Make sure the wall is strong enough to withstand three times the weight of the camera and the bracket.
- Page 7 5. Route the cables through the cable hole, or the side opening. 6. Align the camera with the back box/base plate, and tighten the screws to secure the camera with the back box/base plate. Type I Camera Figure 2-3 Fix the camera to the Ceiling 7.
- Page 8 4. Refer to step 3 of 2.1 Ceiling Mounting to remove dome camera’s bubble and the black liner. 5. Attach the back box/base plate of the dome camera to the wall mounting bracket and secure them with supplied screws. Type II Camera Type I Camera Figure 2-6 Attach the Base Plate to the Bracket 6.
- Page 9 7. Connect the corresponding cables, such as power cord, and video cable. 8. Repeat steps 8 to 9 of the 2.1 Ceiling Mounting to complete the installation. 2.4 Mounting with Inclined Base of Type I Camera Before you start: You need to purchase an inclined base separately. Steps: 1.
-
Page 10: Menu Description
3 Menu Description Purpose: Call the menu by clicking the button on the PTZ Control interface, or call preset No.95. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. TVI DVR Camera Monitor Figure 3-1 Connection 2. - Page 11 Figure 3-3 OUTPUT MODE RESOLUTION Resolution refers to the number of the pixels contained in an image. You can set the resolution as 5 megapixels, 4 megapixels or 1080p. The higher the value, the finer the image is. FRAME RATE Frame rate refers to the number of image output in 1 second.
-
Page 12: Anti-Flicker
EXPOSURE MODE You can set the EXPOSURE MODE as GLOBAL, or BLC. GLOBAL GLOBAL refers to the normal exposure mode which performs exposure according to the whole image brightness. BLC (Backlight Compensation) BLC (Backlight Compensation) compensates light for the front object to make it clear, but this may cause the over-exposure of the background, where the light is strong. - Page 13 COLOR The image is colored in day mode all the time. The image is black and white all the time, and the IR LED turns on in the poor light conditions. AUTO Automatically switch COLOR or BW (Black and White) according to actual scene brightness You can turn on/off the INFRARED and set the value of SMART IR in this menu.
-
Page 14: Save And Exit
DNR (Digital Noise Reduction) The DNR function can decrease the noise effect, especially when capturing moving images in poor light conditions and delivering more accurate and sharp image quality. You can set the DNR value from 1 to 10. MIRROR DEFAULT, H, V, and HV are selectable for mirror.