Table of Contents
Advertisement
„ In the event of malfunction during operation
If the indicator lamps on the unit indicator panel light up abnormally during operation due to a lightning strike etc., and operation becomes
impossible, remove the power supply plug, wait at least 5 seconds then reinsert the power supply plug and start operation again.
Phenomenon
The HUM monitor lamp always
indicates a high humidity level
The humidity level indicated on the
unit differs from other hygrometers
Ambient humidity does not rise
Room humidity is high but
Humidifying Operation does not stop
The water supply lamp is lit but
Humidifying Operation does not stop
(the humidifying filter unit continues
to rotate)
Water in the water tank is decreasing
even though Humidifying Operation
is not running
Water is coming out of the air outlet
The airflow rate does not reach the
set level during Humidifying
Operation
• Is the unit positioned next to a window or in a location exposed to
cold wind?
¼ There is a possibility that only the air surrounding the unit is of high humidity.
Try moving the unit to a different location.
• North facing rooms or rooms close to wet areas, such as the bathroom,
become humid easily, so these rooms tend to have a higher humidity.
• Immediately after starting operation, the humidity may be displayed higher
than it actually is, depending on the condition of the air inside the unit.
Let the unit operate for about 1 hour, then check again.
• This is because the flow of air causes temperature and humidity to vary
throughout the room.
Please consider the indications to be a rough estimate of ambient humidity.
• When the indoor or outdoor humidity is low, the walls and floor of the room
are dry, or the room has poor insulation against drafts, the target humidity
may not be readily achieved.
• Is the humidity set to "
Is the airflow rate setting set to "
¼ Set the humidification mode to "
setting.
►Page 17, 18
• Is the odor sensor lamp blinking?
¼ Attach the carbon filter and filter fixing unit properly.
• When indoor or outdoor humidity is high, the walls and floor of the room are
moist, or the room has good insulation against drafts, the target humidity
may be exceeded.
• Is the unit exposed to direct sunlight or warm air from a heating
appliance?
¼ Move the unit to a location without such direct exposure.
• Perform during Humidifying Operation as well as Air Purifying Operation.
If the set humidity is reached during Humidifying Operation, Humidifying
Operation will stop, but Air Purifying Operation will continue.
• Even if the water supply lamp lights up, the humidifying filter unit will
continue to rotate for about 90 minutes in order to reduce the amount of
water remaining in the humidifying tray. If you want to continue Humidifying
Operation, please add water to the water tank.
• Even when performing only Air Purifying Operation, if there is water in the
tank, the air will be slightly humidified due to natural evaporation because
of air flow, and the water in the water tank will be used up.
When performing only Air Purifying Operation, discard the water in the
water tank and humidifying tray.
• Are the pre-filter, dust collection filter, humidifying filters, and water
tank attached properly?
¼ Attach properly.
• When you removed the humidifying filters from the frame and
replaced them
• Did you shape the new filters properly before attaching them?
• Did you attach all 2 of them?
• Did you attach them so that the engraved pattern on the frame
matches the pattern on the humidifying filter?
►Page 30
¼ Attach properly.
• Even if you have selected an airflow rate that suits your preferences, if the
water supply lamp lights up, the airflow rate will change to "Quiet".
If you do not want the airflow rate to change to "Quiet", change the setting.
(Depending on the degree of odor and dust, the airflow rate may not
change to "Quiet".)
• When Humidifying Operation is started with the airflow rate set to "Turbo",
"Turbo" airflow rate is suppressed for about 10 minutes. After that, the
airflow rate changes to the set airflow rate, so the operating sound also
changes.
Check points
(Low)" or "
(Standard)"?
(Quiet)" or "
(High)" and increase the FAN
►Page 9, 14, 15, 27
►Page 15, 25, 28, 30, 31
Troubleshooting
(Low)"?
►Page 14
►Page 23, 24
38
Advertisement
Table of Contents
