Advertisement
Quick Links
Advertisement
Related Manuals for Harvest TEC 445Z
Summary of Contents for Harvest TEC 445Z
- Page 1 Installation Manual Model 445Z 55-Gallon Preservative Applicator Forage Harvester 445Z-21-INST 5-21...
- Page 2 European Parliment and the Council of 17 May 2006 and other applicable European Directives including Directive 2004/108/EC on the Electromagnetic compatability. The application of preservatives for hay Harvest Tec system will be turned on after being installed on a farm press has been declard in conformity with the Machinery Directive.
- Page 3 This applicator is designed to apply Harvest Tec buffered acid. The model 445Z Kit includes the following parts: tank, frame, pump, gauge, hose, electronic control box, and miscellaneous hardware. If you are unsure about your kit, contact your local dealer for specifications.
- Page 4 Installation of Applicator Installation of Mounting Brackets and Tank 1. Locate parts 001-4703ZR-A, 001-4703ZR-B, two 001-4703ZR-C and four ¾” x 4 ½” bolts, lock washers and nut. 2. Line up 001-4703ZR-A and 001-4703ZR-B about 18 inches apart on the ground. Slide part 001-4703ZR-C into square mounts and secure with ¾”...
- Page 5 Installation of Mounting Brackets and Tank (continued)
- Page 6 Mount Pump Plate Assembly Locate parts bag 8. Using two 3/8” x 1/4” bolts, locks, washers, and nuts. Mount the U-shaped pump plate mount 001-4647 (right) onto the tank saddle in the mounting holes located between the strap brackets on back of saddle (figure 7).
- Page 7 Installation of Gauge and Hose Manifold A. Drill two 3/8” holes and mount pressure gauge to sheet metal. Bend the gauge bracket to adjust the angle. B. Secure with two 5/16” x 1” flange bolts and flange nuts. Placement of Spray Nozzle Assembly The cross bar on the wind guard above the pick-up head provides a mounting point for the nozzle holders (001-4714J).
- Page 8 Installation of Plumbing A. Tank to Pump 1. Thread elbow (003-EL3412) into the bottom of the tank. 2. Route 1/2” hose from bottom of tank through gap in sheet metal surrounding the baler gauge down to valve on pump intake. 3.
- Page 9 Installation of Controls and Routing the Wire Harnesses A. Locate the control in an area that allows operation for adjusting or turning the controls while operating the baler. B. Route the wire to the starter solenoid on all 12V tractors. Connect the green lead marked + to the hot terminal on the starter.
- Page 10 Model 445Z Base Kit Description Part # Description Part # 50 Gallon Tank 005-9203SQ Side Rail Plate 001-4703ZR-E Tank Cap, Gasket, & Breather P05-9022HBG Front Mount Support 001-4703ZR-D2 Tank Saddle 001-4703X Front Mount Crossmember 001-4703ZR-D1 Tank Strap 001-4402 Long Side Rail...
- Page 11 Model 445Z Base Kit (continued) Description Part # Description Part # 50 Gallon Tank 005-9203SQ Side Rail Plate 001-4703ZR-E Tank Cap, Gasket, & Breather P05-9022HBG Front Mount Support 001-4703ZR-D2 Tank Saddle 001-4703X Front Mount Crossmember 001-4703ZR-D1 Tank Strap 001-4402 Long Side Rail...
- Page 12 Parts Breakdown for Control Box and Drain Fill Kit Model 457 Control Box Ref Description Part # Ref Description Part # Speed dial 006-2022A Power lead 006-4580C U-bracket 001-2012E Pre-Serial # 4549 Control box knob 008-0923 Control box enclosure 006-2015A Power lead 006-4580M Control box cover...
- Page 13 445Z Spray Shield Ref Description Part # Ref Description Part # U bolt 001-4714UBS Tip Strainer 004-1203-100 Tip – White Hose clamp 003-9002 004-XR11008VS Tip – Red 1/4" x 1/4" Fitting 003-A1414 004-XR11004VS 1/4" Sq Tee 003-TT14SQ Nozzle Body 004-4722 1/4"...
- Page 14 Harvest Tec, Inc. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion.
- Page 15 HARVEST TEC, INC. P.O. BOX 63 2821 HARVEY STREET HUDSON, WI 54016 PHONE: 715-386-9100 1-800-635-7468 FAX: 715-381-1792 Email: info@harvesttec.com...
Need help?
Do you have a question about the 445Z and is the answer not in the manual?
Questions and answers