Related Manuals for XAC CL AT-170-R Series
Summary of Contents for XAC CL AT-170-R Series
- Page 1 ESKTOP OBILE AYMENT ERMINAL CL AT-170-R SERIES INSTALLATION GUIDE xCL_AT-170 series: Before using the device, please full charge the battery xCL_AT-170-R-18W To keep the device in good condition...
-
Page 2: Package Content
This symbol is intended to alert the user before starting using the POS. 1. PACKAGE CONTENT USB cable Paper Roll Hand Strap AT-170 Power adaptor (Optional) (Optional) (Optional) 2. DEVICE OVERVIEW AT-170 Key Buttons & Interface Ports (Figure 1) FRONT REAR Right... -
Page 3: Power On/Off The Device
Input: 100 ~240 Vac Output: 5V DC, 2A Caution: Use only the AC adapter approved and provided by XAC Automation Corporation for use with this device. Use of any other AC adapter may cause a risk of fire or explosion. -
Page 4: Using The Magnetic Card Reader
NOTE: When device is in idle or suspend mode, short press power button will wake up the device. When device require to forced shut down, press and hold the power button for 10 seconds 4. USING THE MAGNETIC CARD READER Swipe the card through the slot with magnetic stripe at the back side of the card. -
Page 5: Using The Keypad
6. USING THE KEY PAD After inserting the chip card, press the numeric keys of virtual keypad (Figure 5, as reference) shown on the display to enter the password. Press Cancel (X) key to terminate any current function and press the Enter (O) key to confirm a value or an option. - Page 6 Figure 7 Figure 8 Bottom Cover Removal Warning When removing the bottom cover and screws for the purposes of changing battery, remember to put back the cover and screws before power on the POS. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
-
Page 7: Loading The Paper
10. LOADING THE PAPER STEP 1: Gently pop the printer cover’s latch; then pull the cover upward to open the paper roll cover (Figure 10). STEP 2: Load a roll of thermal paper into the printer. Please ensure the printing-side of the paper will feed out facing the operator. - Page 8 Figure 11-2 Figure 11-3 Finished look of the strap assembly is as Figure 11-4. Figure 11-4...
- Page 9 Federal Communication Commission Interference Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 10 These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when used close to the body is 0.515 W/kg. Industry Canada statement: This device complies with Industry Canada license-exempt RSSs.
- Page 11 Avertissement: 1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; 2) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à...
- Page 12 XAC Automation Corporation. XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or errors made herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of his material.