Related Manuals for Car Solutions QCPASS1581
Summary of Contents for Car Solutions QCPASS1581
- Page 1 Installation Manual Multimedia Interface for Honda Accord/Odyssey 2018- car-solutions.com support@car-solutions.com...
-
Page 2: Specification
Specification Compatibility: Honda Accord/Odyssey 2018~ Interface Input / Output specifications Input: LVDS IN (Car System) *1 LVDS *1 HDMI *1 CVBS (Front Camera) *1 CVBS (Rear Camera) *1 Output: LVDS OUT (Car System) *1 AUDIO OUT*1 Power Spec: Input Power: 8VDC ~ 18VDC Consumption: 5WATT... - Page 3 Components Main Board Power Cable Accord J By J Cable QCPASS1581 HPOWER0267 HARETC0371 LCD Cable Multi Cable IR Cable HLCDCA0067 HARETC0363 HIRCAB0002 HLCDCA0068 Button Cable UART Cable Remote CTRL. HARETC0001 HTOUCH0015 REMOTE0001 car-solutions.com support@car-solutions.com...
- Page 4 Components with Options Odyssey Jack by Jack Cable Option OPTION Odyssey J By J Cable HARETC0372 car-solutions.com support@car-solutions.com...
-
Page 5: Dip Switch Settings
DIP Switch Settings * ON: DOWN / OFF: UP Please make sure to disconnect the power cable of interface and reconnect to apply dip switch setting whenever changing DIP switch. FUNCTION Dip S/W SELECT OFF : LVDS Mode LVDS ON : LVDS Mode Skip OFF : HDMI Mode HDMI ON : HDMI Mode Skip... -
Page 6: Remote Control
Remote Control FUNCTION POWER & PIP MENU Activating OSD menu Making a selection, changing image display ▲ Moving upward ▼ Moving downward Moving leftward ◀ (If you press this button 2 seconds long, you can access the factory mode) Moving rightward ▶... -
Page 7: Factory Settings
Factory Settings IMAGE BRIGHTNESS IMAGE Setting for image display CONTRAST PARK SATURATION FUNC UTIL INFO SHARPNESS PAS TYPE : PAS ON IMAGE PARK PAS SETUP FUNC REAR TYPE : CAN UTIL RADAR FUNC : OFF INFO PARK PAS TYPE: Select parking line type. NOT USED: Do not use parking line PAS ON: No Use PAS OFF: Use fixed parking line... - Page 8 Factory Settings FUNCTION CAR MODEL : Odyssey IMAGE CAR MODEL: AUTO FCAM : OFF PARK Auto detect (no selection) FUNC LVDS MODEL : QX-720P AUTO FCAM: UTIL HD1 MODEL : SUNE10 Front Camera Display Setting INFO LVDS MODEL: CarPlay, Navigation Model Setting HD1 MODEL: DTV, Navigation Model Setting UTIL...
-
Page 9: Installation Diagram
Installation Diagram Monitor Command OEM LCD Cable Supplied LCD Cable with Male Supplied LCD Cable Connector with Female Connector T/S OUT Pin#2 is UART-TX for UART Touch Power/CAN Rear Camera IN *1 HDMI IN *1 Front Camera IN *1 Audio OUT *1 CARPLAY Or Android * Please refer to the next page for Power/CAN Cable connection. - Page 10 LCD Cable Connection 1. Please unplug the below highlighted OEM LCD cable from monitor. 2. Connect provided LCD female connector with OEM LCD connector and Interface OEM IN port. 3. Connect provided LCD male connector to the monitor and interface OEM OUT port.
- Page 11 Power/CAN Cable Connection_ Accord 1. Please unplug above highlighted OEM Power/CAN cable from the head unit. 2. Plug in OEM Power/CAN connector to the provided Jack by Jack female connector. 3. Plug in provided Jack by Jack male connector to the head unit. car-solutions.com support@car-solutions.com...
- Page 12 Power/CAN Cable Connection_ Odyssey Please unplug above highlighted OEM Power/CAN cable from the Instrument monitor. Plug in OEM Power/CAN connector to the provided Jack by Jack female connector. 3. Plug in provided Jack by Jack male connector to the instrument monitor. car-solutions.com support@car-solutions.com...
- Page 13 OEM Button Activation_ Accord * Please long press below button for mode change. car-solutions.com support@car-solutions.com...
- Page 14 OEM Button Activation_ Odyssey * Please long press below button for mode change. car-solutions.com support@car-solutions.com...
- Page 15 Multi Cable Drawing car-solutions.com support@car-solutions.com...
- Page 16 Power Cable Drawing car-solutions.com support@car-solutions.com...
-
Page 17: Cautions Before Installation
Cautions Before Installation 1. Ignition key should be taken off before starting installation, interface power connection must be the last step in installation. 2. Power cable should be separated when connecting interface. 3. Should be no any electronic devices or magnetic pole around installation place. -
Page 18: Troubleshooting
Trouble Shooting Q. I cannot change mode A. Check connection of Ground cable and IR Cable. Check LED lamp is on, if not check connection of POWER cable. Q. All I got on the screen is black. A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well.