Related Manuals for Car Solutions qpi-lvtx-astm
Summary of Contents for Car Solutions qpi-lvtx-astm
- Page 1 Updated date : 2015.11.10 Model : RGB-LE-V4.0 RGB-LE CONVERTER Specification & Installation...
-
Page 2: Table Of Contents
Contents 1. Before installation 1.1 Main specification 1.2 System diagram 1.3 Components 1.4 Exterior 2. Setup 2.1 DIP switch 2.2 Remote controller 2.3 Power cable wiring diagram 3. Installation 3.1 Cautions on installation 3.2 Installation diagram 4. Troubleshooting... -
Page 3: Main Specification
1.1 Main Specification 1. Input Spec. (MULTI VIDEO INTERFACE) -. 2 x CVBS Input (External video source). -. 1 x CVBS (REAR CAMERA) Input (Rear camera source) -. 1 x Analog RGB Input (Car commander original monitor output) -. 1 x Analog RGB Input (Navigation System output)-OPTION 2. -
Page 4: System Diagram
1.2 System Diagram Remote Control Switch for source toggle & REAR SENSE Navigation Input (Analog RGB) DISPLAY CAR Installation OEM LCD CVBS 1 CVBS 2 VIDEO CIRCUIT CVBS VIDEO MUX (Rear Camera) POWER CIRCUIT CAR SCREEN INPUT HEADREST CVBS (CAR MAIN BOARD) MONITOR DIP S/W Power Input... -
Page 5: Components
1.3 Components SEL cable * 1ea RGB OUT cable (8P) * 1ea (HSELCA0001) RGB OEM cable(5P) * 1ea (HRGBCA0002) (HRGBCA0003) RGB NAVI cable * 1ea (HNAVIC0002) REMOTE CONTROL * 1ea (REMOTE0001) IR cable * 1ea POWER cable * 1ea MODE cable * 1ea (HIRCAB0002) (HPOWER0001) (HARETC0001) -
Page 6: Exterior
1.4 Exterior ⑬ ⑫ ⑪ ⑩ ⑨ ⑧ Dimension Horizontal length 129mm Vertical length 75mm Height 21mm ⑬ ⑫ ⑪ ⑩ ⑨ ⑧ ① POWER ② MODE ③ IR ④ V1 ⑤ V2 ⑥ R/V ⑦ V-OUT ⑧ NAVI (IN) ⑨... -
Page 7: Dip Switch
2.1 DIP switch #PIN Function DIP S/W selection ON : Skipping RGB Mode RGB INPUT skip OFF : RGB Display ON : Skipping CVBS1 CVBS1 Skip OFF : CVBS1 Display ON : Skipping CVBS2 * Caution CVBS2 Skip - If the displayed screen vibrates, please try to OFF : CVBS2 Display operate Dip S/W No. -
Page 8: Remote Controller
2.2 Remote controller Function RESET – long press MENU Not for use Making a selection ▲ Display brightness higher ▼ Display brightness lower ◀ Chroma higher ▶ Chroma lower SIZE : 85 * 40 * 8 (mm) -
Page 9: Power Cable Wiring Diagram
2.3 Power cable wiring diagram ⑥ ⑤ ④ FILTER & FUSE BOX ③ ② ① ① GND (black) ② I-Drive use) ③ FMTX antenna ④ N.C ⑤ ACC(red) ⑥ REAR(gray) Blue FMTX Orange I - DRV Gray Black Blue 990mm Orange Black Grey... -
Page 10: Installation
Cautions on installation Ignition key should be taken off before starting installation, interface power connection must be the last step in installation. Power cable should be separated when connecting interface. Should be no any electronic devices or magnetic pole around installation place. ... -
Page 11: Installation Diagram
Installation diagram SEL-OUT DIP S/W RGB(OUT) OEM(IN) NAVI(IN) RGB CONVERTER(LE) LAMP-RV FMTX POWER MODE V-OUT I-DRV... -
Page 12: Troubleshooting
Troubleshooting Q. I can not switch A/V sources. A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable. Q. All I got on the screen is black. A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well. (Second lamp indicates AV sources connected works well.) Check interface connection has been done well.
Need help?
Do you have a question about the qpi-lvtx-astm and is the answer not in the manual?
Questions and answers