Rear Panel Features And Connections - Extron electronics Quantum Ultra Series Setup Manual

Quantum Ultra Series • Setup Guide (Continued)
3. Connect the video inputs and outputs. Connect HDMI sources to connectors on the installed HDMI input cards. If
IN SMD 100 input cards are installed (Quantum Ultra and Quantum Ultra II only), connect the LAN connectors on the cards
to a network for streaming sources. Connect DTP receivers (Quantum Ultra and Quantum Ultra II only) or HDMI displays
to connectors on the output cards. Secure each HDMI device cable to the connector with a provided LockIt
Lacing Bracket.
4. Connect a control device — For remote control, connect a control device or a computer to:
•
The RJ-45 LAN A to enable configuration of the Quantum Ultra Series device via SIS commands, VCS, or EMS
•
(Optional) The USB mini B Config connector to enable configuration and control via SIS commands or VCS
•
(Optional) The 3-pole captive screw RS-232 connector to enable serial control via SIS commands
5. Connect power to the Quantum Ultra or Ultra II primary and redundant (optional) IEC connectors.
6. Power on the unit and all connected devices.
7. Download and install VCS on your computer.
8. Configure sources, displays, EDID, and presets for your videowall using VCS (see
VCS
on page 5).

Rear Panel Features and Connections

NOTE: Figure 1 shows the rear panel of a Quantum Ultra 610. The Quantum Ultra II 610 rear panel is identical except for IEC
C20 AC connectors and the product name in the upper-left corner. The Quantum Ultra and Ultra II 305, Ultra Connect 84,
and Ultra Connect 128 have similar rear panels except they are 3U high, have five card slots, and have no redundant power
connector.
Quantum Ultra 610
QUANTUM ULTRA 610
A A A
B B B
POWER
DISCONNECT POWER
CORD BEFORE
SERVICING
C C C
A Primary AC power connector
B Redundant power connector
C Power switch
D HDMI Out system output connector
E
USB system connectors
Figure 1.
Quantum Ultra 610 Rear Panel
A Primary AC power connector — Connect AC power to this IEC connector for the primary power supply.
2
INPUTS
INPUTS
INPUTS
INPUTS
INPUTS
INPUTS
OUTPUTS
OUTPUTS
OUTPUTS
OUTPUTS
SYSTEM REMOTE LAN
OUTPUTS
A B
RS-232
CONFIG
Tx Rx G
D D D E E E F F F G G G H H H
(Quantum Ultra and Ultra II 610 only)
LAN A
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
DTP POWER SIG LINK SIG LINK SIG LINK
OVER TP OVER TP
12V
4A MAX
Tx Rx G Tx Rx Tx Rx G Tx Rx
OUT 1 OUT 2 OUT 3
SIG LINK SIG LINK SIG LINK
DTP POWER OVER TP OVER TP
12V
4A MAX
Tx Rx G Tx Rx Tx Rx G Tx Rx
OUT 1 OUT 2 OUT 3
F USB Config control connector
G RS-232 control connector
H LAN connectors A and B
I Input and output card slots
HDMI Cable
®
Configuring the Videowall Using
QUANTUM IN SMD 100
LAN B
QUANTUM IN4HDMI
4
QUANTUM IN4HDMI
4
QUANTUM IN4HDMI
4
QUANTUM IN4HDMI QUANTUM IN4HDMI
4
4
QUANTUM OUT4HDMI
4
QUANTUM OUT4HDMI
4
QUANTUM OUT4HDMI
4
QUANTUM OUT4DTP
SIG LINK
OVER TP OVER TP
DTP
Tx Rx G Tx Rx Tx Rx G Tx Rx
OUT 4
QUANTUM OUT4DTP
SIG LINK
OVER TP OVER TP
DTP
Tx Rx G Tx Rx Tx Rx G Tx Rx
OUT 4
I I I