Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Basta Boatlifts Manuals
  4. Lifting Systems
  5. Over-Center 2k40
  6. Manual

Basta Boatlifts Over-Center 2k40 Manual

Hydraulic aluminum lift
Hide thumbs

Advertisement

Quick Links

Download this manual
Over-Center
2,000 lbs Capacity - Models 2k
ASSEMBLY
INSTALLATION
REPLACEMENT PARTS
2k
50
shown
1-866-GO BASTA
www.gobasta.com
Basta, Inc.
Bellevue, WA 98005 USA
TM
Hydraulic Aluminum Lift
READ complete manual CAREFULLY
BEFORE attempting assembly or operation
& 2k
40
50
©
Copyright 2020 Basta, Inc.
11/21
L392-0096C

Advertisement

loading
Need help?

Need help?

Do you have a question about the Over-Center 2k40 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Basta Boatlifts Over-Center 2k40

Summary of Contents for Basta Boatlifts Over-Center 2k40

  • Page 1 Over-Center Hydraulic Aluminum Lift 2,000 lbs Capacity - Models 2k & 2k ASSEMBLY READ complete manual CAREFULLY INSTALLATION BEFORE attempting assembly or operation REPLACEMENT PARTS shown 1-866-GO BASTA www.gobasta.com 11/21 © Basta, Inc. Bellevue, WA 98005 USA Copyright 2020 Basta, Inc. L392-0096C...

  • Page 2: Table Of Contents

    The lift should not be used for any other Use a mooring line for additional security. purpose besides the lifting of boats & watercraft. MAXIMUM CAPACITY Only use Basta Boatlifts biodegradable non-toxic 2,000 lb hydraulic fluid - part # Y354-0001. 900 kg...
  • Page 3 OIL INJECTED INTO THE SKIN FROM HIGH PRESSURE LEAKS IN HYDRAULIC SYSTEMS CAN CAUSE SEVERE INJURY. SEEK MEDICAL ATTENTION IMMEDIATELY. USE ONLY BASTA BOATLIFTS BIODEGRADABLE HYDRAULIC FLUID After the lift is assembled and installed, all fasteners should be checked for proper tightness and reinspected periodically.
  • Page 4 17&18 17&18 17&18 17&18 17&18 17&18 11&2 11&2 1&2 1&2 7&2 7&2 7&2 7&2 1&2 1&2 7&2 1&2 7&2 1&2 1&2 7&2 7&2...
  • Page 5 MECHANISM PARTS LIST SEE PAGES 13-14 FOR ELECTRICAL AND HYDRAULIC PARTS ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY. K200-0125 W102-0045 Inner Arm Weldment Foot Pad W117-0001 A427-0014 Bunk Rail Assembly, Left A427-0015 Bunk Rail Assembly, Right W105-0012 Side Rail W111-0012 Base Crossmember...
  • Page 6 ASSEMBLY INSTRUCTIONS NOTE: use a small amount of 'moly' lube on bolt threads NOTE: assemble lift on level ground and adjust legs so that lift base frame is level during lift assembly. NOTE: the 3 different holes shown can be used for pin “9” to allow fine height adjustment after installation DOWN...
  • Page 7 NOTE: DO NOT tighten bolts completely until the H-frames have been installed and squared up (see Step 6) NOTE: DO NOT tighten bolts completely until the H-frames have been installed and squared up (see Step 6) Assemble lift on level ground and adjust legs so that lift base frame is level during lift assembly.
  • Page 8 ASSEMBLY INSTRUCTIONS NOTE: use a small amount of 'moly' lube on bolt threads NOTE: orient flat faces toward lift center Assemble lift on level ground and adjust legs so that lift base frame is level during lift assembly.
  • Page 9 NOTE: forward H-frame BOTH is shown. Aft H-frame H-FRAMES installation is the same are installed with curved Bushings are pre-installed - side up remove cable ties used for shipping NOTE: adjust side rails so that pivot blocks are tight against the H-frames. Then tighten bolts installed in Steps 2 &...
  • Page 10 ASSEMBLY INSTRUCTIONS NOTE: use a small amount of 'moly' lube on bolt threads Install cylinder with lift in 'down' position 8+14 NOTE: install plastic washers here washers here NOTE: install cylinders with hose fittings facing down!
  • Page 11 port points down Important note: Install cylinder with hose fittings facing down! Model 2k only: 17+18...
  • Page 12 ASSEMBLY INSTRUCTIONS NOTE: use a small amount of 'moly' lube on bolt threads The angles and directions of bunk rail assemblies MUST face the directions shown below. LONG SHORT plate plate FORWARD AT AFT bushings are pre-installed Raise lift to install screws for pins. See step 12 for details.

  • Page 13: Parts List And Diagrams

    CONNECT POWER UNIT FEMALE QUICK COUPLER DO NOT SUBMERSE H700-0019 COMPLETE POWER PACKAGE Keep inside dry H653-0001 Prevent unauthorized use - KEEP BOX LOCKED up/down switch power NOTE: NOTE: switch REMOVE SHIPPING PLUG IN REMOVE SHIPPING PLUG IN solar RESERVOIR AND REPLACE RESERVOIR AND REPLACE controller WITH BREATHER PLUG...
  • Page 14 POWER SYSTEM COMPONENTS SOLAR PANEL ASSEMBLY R281-0004 Padlock not included ENCLOSURE C243-0003 NOTE: NOTE: REMOVE SHIPPING PLUG IN REMOVE SHIPPING PLUG IN RESERVOIR AND REPLACE RESERVOIR AND REPLACE WITH BREATHER PLUG WITH BREATHER PLUG BEFORE START-UP BEFORE START-UP CONTROL PANEL ASSEMBLY R815-0008 pre-wired...
  • Page 15 ASSEMBLY INSTRUCTIONS NOTE: use a small amount of 'moly' lube on bolt threads raise lift to install 1/4 x 1.75” bolts ("17") 17+18 17+18 17+18 17+18 Assemble lift on level ground and adjust legs so that lift base frame is level during lift assembly.
  • Page 16 Lower the lift completely, then raise it slightly. Disconnect the hydraulic hose quick couplers in the Power Unit box to separate it from the lift. Move the lift into its operational position Adjust the legs to provide enough water over the lift so that the boat will not have to be "driven"...

  • Page 17: First Use / Adjustments

    FIRST USE AND ADJUSTMENTS First test lift on dry ground for oil leaks, remote control function and correct operation. IMPORTANT: After installation, the legs MUST be adjusted so that the lift frame is level. Lift must move into Over-Center position when fully raised. H-frame arms should appear to be tilted slightly forward.

  • Page 18: Troubleshooting / Faq

    Always leave the boat in the fully raised, Over-Center™ for the environment. This fluid is different than food-grade oil. Only use Basta Boatlifts fluid in your hydraulic system. position with the power off. Q: WHAT IF I GET A NEW BOAT? A new lift Re-leveling the boat lift may be necessary.

  • Page 19: Maintenance

    The hydraulic fluid level should be about one inch below the top of the reservoir with the lift DOWN. DO NOT add fluid with the lift in the raised position! Use only Basta Boatlifts biodegradable hydraulic fluid. DATE: WHAT WAS DONE:...

  • Page 20: Warranty

    Products. on the water. Welcome to the Basta Boatlifts family and Boat Happy! Labor for warranty work to be provided by the Company’s Authorized dealer for a period of 3 years from Warranty Start Date, provided there is an active Authorized Basta Inc.

This manual is also suitable for:

Over-center 2k50