Page 1
BA S TA B OATL IF T S OVER - CE NTE R G ALVA N I Z E D S TE EL LIF T 8,000 lb Capacity Boat Lift Models 8k 53 / 65 / 866-GoBasta GoBasta.com COPYRIGHT 2022 3/22 BASTA INC.
• Do not install the lift alone. • The lift should only be used for lifting boats & watercraft. • Passengers should stand clear of the lift when the lift is in operation. Basta Boatlifts are protected by one or more US Patents www.gobasta.com/patents PAGE 2...
TABLE OF CONTENTS SAFETY ....................P 2 PARTS LIST AND DIAGRAMS ..............P 4-5 ASSEMBLY INSTRUCTIONS ..............P 6-15 OPERATIONAL INSTRUCTIONS ............... P 16 REMOTE CONTROL FOB INFORMATION ........... P 17 TROUBLESHOOTING / FAQ ..............P 18 MAINTENANCE ..................P 19 WARRANTY ..................
PARTS LIST - BOAT LIFT ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY. W110-0025 Aft Crossmember A431-0046 Forward H-Frame (8k W110-0024 Forward Crossmember A431-0016 Forward H-Frame (8k W104-0020 Left Side Rail (8k & 8k A431-0028 Forward H-Frame (8k W104-0028 Left Side Rail (8k A428-0002...
Page 5
ITEM PART NO. DESCRIPTION QTY. R812-0011 Remote Control Master Unit R283-0002 Solar Controller R310-0001 On/Off Switch Up/Down Switch R310-0002 Solar Panel Assembly R281-0004 Power Box Unit, STD C243-0003 POWER PACKAGE #H653-0001 Symbol Glossary for the following pages: Tools needed for the job: •...
ASSEMBLY INSTRUCTIONS Pictured : Steps 1-3 Use a small amount of ‘moly’ lube on bolt threads through the assembly process. Do not tighten any hardware until step 8. Assemble lift on level ground and adjust legs so that lift base frame is level during lift assembly.
Page 8
ASSEMBLY INSTRUCTIONS Pictured : Steps 4-6 Use a small amount of ‘moly’ lube on bolt threads through the assembly process. Forward H-Frame 3/4 x 8 bolts QTY 2 : 3/4 flat washers QTY 2 : 3/4 lock nuts QTY 2 : PAGE 8...
Page 9
Stop Tubes 3/4 x 4-3/4 bolts QTY 2 : 3/8 flat washers QTY 4 : 3/8 lock nuts QTY 2 : - USE TOP HOLES - USE BOTTOM & 8K72 HOLES Aft H-Frame Bushings are pre- installed - remove cable ties used for shipping.
Page 10
ASSEMBLY INSTRUCTIONS Pictured: Steps 7-9 Use a small amount of ‘moly’ lube on bolt threads through the assembly process. Cylinder QTY 2 : 3/4x 3-1/2 clevis pins ring type cotter pins QTY 2 : IMPORTANT Install cylinder with hose fittings facing down! Install cylinders with lift in ‘down’...
Page 11
Bunk Rails After the bunks are installed, adjust the frame to be square and level, then tighten bolts. Install bunks with lift in ‘down’ position. 3/4 x 4 1/2 bolts QTY 4 : 3/4 flat washers QTY 4 : 3/4 lock nuts QTY 4 : Bunk Boards Install bolts toward center...
Page 12
CONNECT POWER UNIT Complete Power Unit Package FEMALE QUICK COUPLER NEGATIVE BATTERY CABLE (BLACK) ON/OFF SWITCH UP/DOWN BREATHER CAP SWITCH HOSE ASSEMBLY POSITIVE BATTERY CABLE (RED) MALE QUICK COUPLER Step 1 : Slide the Hydraulic Hose Assembly through the access hole in the side of the fiberglass enclosure and IMPORTANT attach the ends to their corresponding Quick Couplers.
Page 13
USE DIAGRAM TO HELP PLACE THE LIFT [DIMENSIONS] ARE FOR 8k53 ONLY (DIMENSIONS ARE FOR 8k72 ONLY) PAGE 13...
Page 14
IMPORTANT: The leveling process must be completed to ensure stability of the lift frame and Over-Center safety lock. Level the lift following these instructions while referencing image below: Step 1: Use a tape measure (reference image on right) to determine that the lower frame is level.
Page 15
Re-connect the Hydraulic Hose Quick Couplers inside the Power Unit box. Fully raise lift and finish adjusting the legs so that the base frame is level side-to-side and forward-to-aft. After the lift is assembled and installed, all fasteners should be checked for proper tightness and reinspected periodically.
• Service your lift according to recommended Maintenance (page 19). • Only use Basta Boatlifts approved fluid in lift. Contact Basta Boatlifts or authorized dealer for approved biodegradable hydraulic fluid. • When not in use, store the lift in the upright position to prevent it from being an unknown hazard underwater.
1. Turn off the ON/OFF switch. 2. Wait 20 seconds. in use. If you have questions, contact your local dealer or Basta Boatlifts. 3. Turn power back on, and within 5 seconds of power on, press both the UP and DOWN buttons...
CHANGE THE FLUID? necessary. A: Check the battery connections, clean and A: Basta Boatlifts’ hydraulic fluid lasts between 3-6 years re-secure if necessary. depending on usage. If you begin to hear an increased pitch in the sound of your pump motor, it is likely time to flush your Q : THE PUMP RUNS, BUT THE LIFT hydraulic fluid.
ONLY ADD FLUID WITH LIFT IN support/. DOWN POSITION Hydraulic fluid shown with lift Annual factory approved service is available. in the DOWN position Contact your local dealer or Basta Boatlifts for additional information. 1” inch PAGE 19...
Company’s Authorized dealer for a period of 3 years from Warranty Start Date, provided there is an active Authorized Dealer within 50 miles of the location of the Basta Inc. dba Basta Boatlifts (“Company”) warrants its Products (purchased Product. Labor will not be provided for direct purchases from Company or when an after November 1, 2021) for non-commercial use for a period of, active Authorized Dealer is not located within 50 miles of the location of the Product.